High-Fidelity Measurement of a Superconducting Qubit Using an On-Chip Microwave Photon Counter
A. Opremcak, C. H. Liu, C. Wilen, K. Okubo, B. G. Christensen, D. Sank, T. C. White, A. Vainsencher, M. Giustina, A. Megrant, B. Burkett, B. L. T. Plourde, R. McDermott
We describe an approach to the high-fidelity measurement of a superconducting qubit using an on-chip microwave photon counter.The protocol relies on the transient response of a dispersively coupled measurement resonator to map the state of the qubit to "bright" and "dark" cavity pointer states that are characterized by a large differential photon occupation.Following this mapping, we photodetect the resonator using the Josephson photomultiplier, which transitions between classically distinguishable flux states when cavity photon occupation exceeds a certain threshold.Our technique provides access to the binary outcome of projective quantum measurement at the millikelvin stage without the need for quantumlimited preamplification and thresholding at room temperature.We achieve raw single-shot measurement fidelity in excess of 98% across multiple samples using this approach in total measurement times under 500 ns.In addition, we show that the backaction and crosstalk associated with our measurement protocol can be mitigated by exploiting the intrinsic damping of the Josephson photomultiplier itself.
We describe an approach to the high-fidelity measurement of a superconducting qubit using an on-chip microwave photon counter.The protocol relies on the transient response of a dispersively coupled measurement resonator to map the state of the qubit to "bright" and "dark" cavity pointer states that are characterized by a large differential photon occupation.Following this mapping, we photodetect the resonator using the Josephson photomultiplier, which transitions between classically distinguishable flux states when cavity photon occupation exceeds a certain threshold.Our technique provides access to the binary outcome of projective quantum measurement at the millikelvin stage without the need for quantumlimited preamplification and thresholding at room temperature.We achieve raw single-shot measurement fidelity in excess of 98% across multiple samples using this approach in total measurement times under 500 ns.In addition, we show that the backaction and crosstalk associated with our measurement protocol can be mitigated by exploiting the intrinsic damping of the Josephson photomultiplier itself.
High-fidelity, efficient quantum nondemolition readout of quantum bits is integral to the goal of quantum computation. As superconducting circuits approach the requirements of scalable, universal fault tolerance, qubit readout must also meet the demand of simplicity to scale with growing system size. Here we propose a fast, high-fidelity, scalable measurement scheme based on the state-selective ring-up of a cavity followed by photodetection with the recently introduced Josephson photomultiplier (JPM), a current-biased Josephson junction. This scheme maps qubit state information to the binary digital output of the JPM, circumventing the need for room-temperature heterodyne detection and offering the possibility of a cryogenic interface to superconducting digital control circuitry. Numerics show that measurement contrast in excess of 95% is achievable in a measurement time of 140 ns. We discuss perspectives to scale this scheme to enable readout of multiple qubit channels with a single JPM.
Fast, high-fidelity measurement is a key ingredient for quantum error correction. Conventional approaches to the measurement of superconducting qubits, involving linear amplification of a microwave probe tone followed by heterodyne detection at room temperature, do not scale well to large system sizes. We introduce an approach to measurement based on a microwave photon counter demonstrating raw single-shot measurement fidelity of 92%. Moreover, the intrinsic damping of the photon counter is used to extract the energy released by the measurement process, allowing repeated high-fidelity quantum nondemolition measurements. Our scheme provides access to the classical outcome of projective quantum measurement at the millikelvin stage and could form the basis for a scalable quantum-to-classical interface.
Superconducting circuits have recently become a major contender for the implementation of quantum computers owing to their compatibility with existing microchip fabrication technologies. Their utility stems largely from their ability to be coupled with resonant cavities for the purposes of trapping and relaying microwave radiation. Because of this feature, scientists are able to transmit quantum information from a variety of qubits. Though quantum-limited amplifiers exist, unfortunately there currently exists no microwave photon counter capable of single shot quantum detection. Hence, we use superconducting circuits with Josephson junctions to design a microwave photon detector based on a modified phase qubit that exhibits a bandwidth of 4GHz, and a detection fidelity of 98%. We use metastable barrier transition (driven by incident photons) to create an avalanche effect analogous to current photo-diodes. Linear coupling of the junction flux with the radiation permits photodetection from an arbitrary quantum source in the GHz range. We show the device to be robust to changes in drive frequency, temporal photon width, and resonator quality factor, and we optimize our device with respect to these parameters. We show the device to be stable over the necessary time scales, and yet sensitive enough to accurately measure photons on demand.
In the quest to build a fault-tolerant quantum computer, superconducting circuits based on Josephson junctions have emerged as a leading architecture. Coherence times have increased significantly over the last two decades, and processors with ∼ 50 qubits have been experimentally demonstrated. These systems traditionally utilize microwave frequency control signals, and heterodyne based detection schemes for measurement. Both of these techniques rely heavily on room temperature microwave generators, high-bandwidth lines from room temperature to millikelvin temperatures, and bulky non-reciprocal elements such as cryogenic microwave isolators. Reliance on these elements makes it impractical to scale existing devices up a single order of magnitude, let alone the 5-6 orders of magnitude needed for performing fault-tolerant quantum algorithms. Here, I present results that suggesting superconducting digital logic, namely Single Flux Quantum (SFQ) logic, can replace analog control and measurement techniques, avoiding the significant overhead involved. I describe a scheme for measuring qubits with a device known as a Josephson Photomultiplier (JPM), which crucially stores the result of a qubit measurement in a classical circulating supercurrent within the device and allows for integration with SFQ detection circuitry. This technique is experimentally demonstrated, with single-shot measurement fidelity of 92%. Two methods for accessing this measurement result are presented, one utilizing ballistic fluxons, and another utilizing flux comparison. Initial experimental results of the latter are presented. In addition, I describe a scheme for controlling qubits with sequences of digital SFQ pulses. This method is then used to control a qubit without a microwave signal generator, with results of an average single-qubit gate fidelity of around 95%. When combined, these techniques form a nearly fully digital interface to superconducting qubits, which could allow these systems to scale much more easily.
We present a method for measuring the internal state of a superconducting qubit inside an on-chip microwave resonator. We show that one qubit state can be associated with the generation of an increasingly large cavity coherent field, while the other remains associated with the vacuum. By measuring the outgoing resonator field with conventional devices, an efficient single-shot QND-like qubit readout can be achieved, enabling a high-fidelity measurement in the spirit of the electron-shelving technique for trapped ions. We expect that the proposed ideas can be adapted to different superconducting qubit designs and contribute to the further improvement of qubit readout fidelity.
As superconducting quantum processors increase in size and complexity, the scalability of standard techniques for qubit control and readout becomes a limiting factor. Replacing room temperature analog components with cryogenic digital components could allow for the realization of systems well beyond the current state-of-the-art qubit arrays with tens of qubits. The standard technique for performing a qubit measurement with heterodyne readout uses a quantum-limited cryogenic amplifier chain and requires bulky microwave components inside the refrigerator with multiple control lines and pump signals. Additionally, the result is only accessible in software at room temperature. An alternative method for measuring qubits involves mapping the qubit state onto the photon occupation in a microwave cavity, followed by subsequent photon detection using a Josephson photomultiplier (JPM). The JPM measures the qubit and stores the result in a classical circulating current. To make use of this result, we can leverage existing single flux quantum (SFQ) circuitry. An underdamped Josephson transmission line (JTL) can be coupled to the JPM and fluxons traveling along the JTL are accelerated or delayed, depending on the circulating current state of the JPM. This fluxon delay can then be converted to an SFQ logic signal resulting in a digital qubit readout with a proximal microfabricated device, paving the way for cryogenic digital feedback necessary for error-correcting codes.