We present a comprehensive study of internal quality factors in superconducting stub-geometry three-dimensional cavities made of aluminum. We use wet etching, annealing, and electrochemical polishing to improve the as machined quality factor. We find that the dominant loss channel is split between the two-level system loss and an unknown source with a 40:60 proportion. A total of 17 cavities of different purity, resonance frequency, and size were studied. Our treatment results in reproducible cavities, with 10 of them showing internal quality factors above 80 × 106 at a power corresponding to an average of a single photon in the cavity. The best cavity has an internal quality factor of 115 × 106 at a single photon level.
We present a comprehensive study of internal quality factors in superconducting stub-geometry three-dimensional cavities made of aluminum. We use wet etching, annealing, and electrochemical polishing to improve the as machined quality factor. We find that the dominant loss channel is split between the two-level system loss and an unknown source with a 40:60 proportion. A total of 17 cavities of different purity, resonance frequency, and size were studied. Our treatment results in reproducible cavities, with 10 of them showing internal quality factors above 80 × 106 at a power corresponding to an average of a single photon in the cavity. The best cavity has an internal quality factor of 115 × 106 at a single photon level.
Three-dimensional microwave cavities have recently been combined with superconducting qubits in the circuit quantum electrodynamics architecture. These cavities should have less sensitivity to dielectric and conductor losses at surfaces and interfaces, which currently limit the performance of planar resonators. We expect that significantly (>103) higher quality factors and longer lifetimes should be achievable for 3D structures. Motivated by this principle, we have reached internal quality factors greater than 0.5 × 109 and intrinsic lifetimes of 0.01 s for multiple aluminum superconducting cavity resonators at single photon energies and millikelvin temperatures. These improvements could enable long lived quantum memories with submicrosecond access times when strongly coupled to superconducting qubits.
Abstract Dielectric losses are one of the key factors limiting the coherence of superconducting qubits. The impact of materials and fabrication steps on dielectric losses can be evaluated using coplanar waveguide (CPW) microwave resonators. Here, we report on superconducting CPW microwave resonators with internal quality factors systematically exceeding 5 × 106 at high powers and 2 × 106 (with the best value of 4.4 × 106) at low power. Such performance is demonstrated for 100-nm-thick aluminum resonators with 7–10.5 um center trace on high-resistivity silicon substrates commonly used in Josephson-junction based quantum circuit. We investigate internal quality factors of the resonators with both dry and wet aluminum etching, as well as deep and isotropic reactive ion etching of silicon substrate. Josephson junction compatible CPW resonators fabrication process with both airbridges and silicon substrate etching is proposed. Finally, we demonstrate the effect of airbridges’ positions and extra process steps on the overall dielectric losses. The best quality factors are obtained for the wet etched aluminum resonators and isotropically removed substrate with the proposed ultrasonic metal edge microcutting.
We describe the fabrication and measurement of microwave coplanar waveguide resonators with internal quality factors above 107 at high microwave powers and over 106 at low powers, with the best low power results approaching 2×106, corresponding to ∼1 photon in the resonator. These quality factors are achieved by controllably producing very smooth and clean interfaces between the resonators’ aluminum metallization and the underlying single crystal sapphire substrate. Additionally, we describe a method for analyzing the resonator microwave response, with which we can directly determine the internal quality factor and frequency of a resonator embedded in an imperfect measurement circuit.
In this master's thesis, I present the design, fabrication, and characterisation of superconducting microwave resonators. These resonators are quarter-wavelength coplanar waveguide resonators, operating at resonance frequencies between 4 GHz and 8 GHz. This kind of resonator is a key component in several applications, ranging from quantum computation devices to parametric amplifiers. Minimising the losses (achieving high internal quality factors) in these resonators is important to maximise performance of the applications they are used for. During the thesis work, we have studied several possible changes to improve the resonator quality.\n\nFabrication of the resonators was done in the Nanofabrication Laboratory at Chalmers University of Technology, and consist of the following steps: cleaning a sapphire or silicon wafer, depositing a layer of superconducting niobium, photolithography, and etching the waveguide. We then measured the resonators in a cryogen-free dilution refrigerator, at a temperature of 10 mK. The measurements consisted of a power sweep, in order to quantify the quality factor at high and low excitation powers. As an example, the first resonator we fabricated had a quality factor of 4.3 x 10^4 at high power (about 10^5 photons in the resonator), and quality factor of 3.7 x 10^4 at the single-photon level.\n\nWe then investigated different loss mechanisms that we expect to negatively affect the quality factor, and how to reduce this loss. Firstly, to reduce radiation losses and magnetic vortex losses, we reduced the lateral dimensions of the resonator. Secondly, as two-level system (TLS) losses are believed to mainly reside at the surfaces of the materials and interfaces between them, we etched into the substrate to selectively move a part of the TLS away from the resonator. We also studied the effect of the meandering of the resonator on the quality factor, as well as using two different etching gasses.\n\nBy gathering all this data, we were then able to compare the different combinations to see the effect of the changing parameters. In conclusion, the reduced lateral dimensions and the removal of part of the substrate indeed reduce the losses, as expected from the theory. We also found interesting behaviour with regards to the meandering, namely that having a meandered structure negatively affects the quality factor.\n\nCombining all results, we can give a guideline for the fabrication of resonators in the future, which gave us a quality factor up to 4.9 x 10^5 at high excitation power, and 3.0 x 10^5 at the single photon level.
Abstract Quantum bits (qubits) with long coherence times are an important element for the implementation of medium- and large-scale quantum computers. In the case of superconducting planar qubits, understanding and improving qubits’ quality can be achieved by studying superconducting planar resonators. In this paper, we fabricate and characterize coplanar waveguide resonators made from aluminum thin films deposited on silicon substrates. We perform three different substrate surface treatments prior to aluminum deposition: one chemical treatment based on a hydrofluoric acid clean; one physical treatment consisting of a thermal annealing at 880 °C in high vacuum; and one combined treatment comprising both the chemical and the physical treatments. The aim of these treatments is to remove the two-level state (TLS) defects hosted by the native oxides residing at the various samples’ interfaces. We first characterize the fabricated samples through cross-sectional tunneling electron microscopy, acquiring electron energy loss spectroscopy maps of the samples’ cross sections. These measurements show that both the chemical and the physical treatments almost entirely remove native silicon oxide from the substrate surface and that their combination results in the cleanest interface. Additionally, we analyze the effects of the various substrate treatments on the roughness of the silicon surface by means of atomic force microscopy surface morphology mapping. We then study the quality of the resonators by means of microwave measurements in the ‘quantum regime’, i.e., at a temperature T ∼ 10 mK and at a mean microwave photon number 〈 n ph 〉 ∼ 1 . In this regime, we find that both surface treatments independently improve the resonator’s intrinsic quality factor by ≈172%. The highest quality factor is obtained for the combined treatment, Q i ≈ 0.82 million, corresponding to an improvement by ≈256%. Finally, we find that the TLS quality factor averaged over a time period of 3 h is ∼3 million at 〈 n ph 〉 ∼ 10 , indicating that substrate surface engineering can potentially reduce the TLS loss below other losses such as quasiparticle loss and flux noise.
The recent implementation of three-dimensional microwave cavities coupled to superconducting transmon qubits has led to dramatic improvements in qubit coherence times [1]. Besides the superconducting aluminum cavities that have been used in many such measurements, other recent experiments have utilized copper cavities [2] with coherence times now approaching 0.1 ms. We are investigating the effects on the quality factor for three-dimensional copper cavities that have the cavity-wall surfaces electropolished and coated with a superconducting tin layer. The copper base provides a good path for thermalizing the cavity walls and qubit chip, while the surface treatment reduces the microwave loss. We have measured a superconducting transmon qubit in such a cavity and we report our low-temperature coherence results on the same qubit and cavity measured in two different labs.