Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2003.10241 · Applied Physics Letters

Suppression of radiation loss in high kinetic inductance superconducting co-planar waveguides

Sebastian Hähnle, N. v. Marrewijk, Akira Endo, K. Karatsu, David Johannes Thoen, Vignesh Murugesan, J. J. A. Baselmans

Published May 4, 2020• 26 citations
arXivHTMLPDF

Abstract

We present a lab-on-chip technique to measure the very low losses in superconducting transmission lines at (sub-) mm wavelengths. The chips consist of a 100 nm-thick NbTiN Co-planar Waveguide (CPW) Fabry–Pérot (FP) resonator, coupled, on one side, to an antenna and, on the other side, to a Microwave Kinetic Inductance detector. Using a single frequency radiation source allows us to measure the frequency response of the FP around 350 GHz and deduce its losses. We show that the loss is dominated by radiation loss inside the CPW line that forms the FP and that it decreases with the decreasing linewidth and increasing kinetic inductance as expected. The results can be quantitatively understood using SONNET simulations. The lowest loss is observed for a CPW with a total width of 6 μm and corresponds to a Q-factor of ≈15 000.

DOI
10.1063/5.0005047

Related papers

Antenna-coupled Microwave Kinetic Inductance detectors (MKIDs) for mm and submm imaging arrays

Anastasios Vayonakis, James A. Schlaerth, S. Kumar +9 more

We present results from completely lithographic antenna-coupled Microwave Kinetic Inductance detectors (MKIDs). MKIDs are superconducting resonators with resonant frequency and quality-factor which are highly sensitive to changes in the density of the quasiparticle population which occurs when photons above the superconducting gap energy are absorbed. The resonators are coupled to submm light through on-chip phased-array slot antennas. Each planar antenna consists of an array of N long slots which are fed along their length at M points. The resulting N*M feed points are combined in-phase using a binary summing tree made of low-loss superconducting microstrip lines. Due to its large size, the resulting planar antenna produces a narrow beam pattern and can therefore be used without additional optical coupling elements such as feedhorns or substrate lenses. The output of the antenna is a single superconducting thin-film microstrip line which can be efficiently coupled to one (or more) kinetic inductance coplanar waveguide resonators to produce a single (or multi-color) pixel in an imaging focal plane array, using in-line lumped element lithographic band-pass filters. Such highly integrated architectures can be easily fabricated on a single substrate, and many detectors can be frequency multiplexed through coupling to a single feedline. Microwave readout provides a lot of bandwidth per detector, allowing a large number of pixels to be read using a single cryogenic microwave amplifier and warm readout electronics.

Softwaretechnik-Trends•Apr 1, 2008•1 citation

Performance of a KID: On the influence of the resonator geometry on the noise and Q-factor of a kinetic inductance detector

Kee Scholten

Space-based astronomy is in need of a photon-noise limited detector with multiplexing opportunities. The kinetic inductance detector (KID) is capable of both properties. An incoming photon breaks Cooper pairs in the superconducting layer of the KID, which leads to a change in inductance, which can be detected with phase- and amplitude read-out. Photon noise, generation-recombination noise are inevitable noise sources, but two-level system noise can be minimized by adjusting the resonator and its geometry. To gain insight in the noise and loss sources this thesis investigates the difference between microstrip and co-planar waveguide resonators; and the difference between a silicon substrate and a silicon-on-insulator substrate. Numerical analysis shows that: noise in all types of resonators are dielectric bulk dominated; an Al superconducting layer shows has different losses in terms of Q-factor, compared to a NbTiN superconducting layer, but quantitatively the same internal Q-factor in the order of 105 is achieved; an Al superconducting layer in a microstrip has 5dBc/Hz and 2dBc/Hz higher noise in the metal-air and metal-edge interfaces, respectively, compared to a NbTiN superconducting layer; an Al on Si CPW and microstrip have the same Q-factor performance; an Al on Si CPW has a 2-8dBc/Hz more noise at all interfaces compared to an Al on Si microstrip; a buried oxide layer has no influence on the loss in terms of the Q-factor for 100nm Al on Si substrate CPWs; and that the noise of an Al on SOI CPW is bulk dominated, and the dielectric bulk contributes 10dBc/Hz more to the noise, compared to an Al on Si CPW. Experimental analysis shows that a gapwidth of wgap ? 10?m for Al on SOI CPWs shows no response, due to high two-level system noise. Low Q-factors in the order of 104 have been measured for Al on SOI CPWs, which is low compared to literature. A high set-up noise of -85dBc/Hz and divergent relationships with the internal power indicate that TLS-noise does not dominate the measurements, and set-up negatively influences the measurements. In conclusion, the resonator geometry is an important factor for the performance of a KID in terms of noise and Q-factors. A buried oxide layer has no consequence for the Q-factor, and negatively affects the noise of a CPW.

•Sep 24, 2015•0 citations

Ultra high quality factor resonators for kinetic inductance detectors

G. Hammer, S. Wünsch, K. Ilin +1 more

The sensitivity of a kinetic inductance detector is determined by the performance of the cavity circuit and therefore a high quality factor and low phase noise are required. We developed superconducting niobium coplanar waveguide resonators for kinetic inductance detectors at a resonance frequency of 6 GHz. The length of the resonators is adjusted to a quarter of a wavelength which corresponds to ≈ 5.3 mm in our geometry. Different layouts with coplanar waveguide transmission line topology for the resonator were designed and simulated. Some parameters of the device fabrication process were varied. The niobium thin films were deposited by magnetron sputtering on sapphire substrates kept at ambient temperature. The resonators were patterned by photolithography and reactive ion etching and measured at helium temperatures. Because of the quarter wave geometry with one shorted end the reflection parameter was measured. We have studied the influence of the coupling capacitances on quality factor. The optimization includes microwave simulations and implementation in different resonator structures. The measurements of optimized devices showed a very high quality factor above one million (10 6 ). The obtained results and perspective on further development of resonators will be discussed.

Journal of Physics Conference Series•Feb 1, 2008•12 citations

Design and measurement of superconducting microwave kinetic inductance detectors

Florian Blauth

Microwave kinetic inductance detectors (MKID) are superconducting broadband direct detectors. If a superconducting thin film patterned into a resonator is illuminated with photons, Cooper pairs break up and the kinetic inductance of the film changes. This shifts the resonance frequency downwards and the dissipation of the resonator increases, which can be detected in the phase and amplitude of a transmitted signal. \n \nIn this thesis, a waveguide coupled MKID is designed and simulated. 350 GHz radiation is coupled into a copper waveguide via a horn antenna. A waveguide probe leads the signal onto a 9 µm silicon membrane where it is absorbed in a 40 nm superconducting aluminum film which is the inductive part of a superconducting resonator. The capacitor of the resonator is made of niobium. Two versions of the device are developed, a transmission line resonator and a lumped element resonator design. The new design will enable an accurate understanding of the optical sensitivity of MKIDs and allow comparison of different resonator materials. Since two different resonator types are used, the direct comparison of transmission line and lumped resonators will also be possible. \n \nA measurement setup is developed including an ADR cryostat to cool MKID devices down to below 40 mK. An analog readout system using either a vector network analyzer or an IQ mixer is designed and built. The necessary software to control the ADR, the temperature monitoring, the readout signal generation and detection and the signal acquisition of the setup is also developed. \n \nThe waveguide coupled MKID design is fabricated in our in-house microfabrication laboratory and measured in the new setup. In my measurements, the devices do not show a resonance feature. The VNA and DC measurements are analyzed to determine a plausible hypothesis of the failure. The devices are diagnosed for critical issues during fabrication which will be addressed in a future iteration. \n \nTo verify the measurement setup, a test device of the IRAM NIKA 2 MKID camera is measured and the complete analysis pipeline is exercised. The quasi-particle lifetime in the aluminum thin films is measured and a dark and optical noise equivalent power are determined. The results are within the uncertainty comparable to measurements of IRAM themselves. \n \nA test chip designed in my master thesis that contains eight NbTiN resonators is measured in the new setup and non-linear effects under strong readout power are studied. Parametric amplification and oscillation of a resonator are shown qualitatively.

•Oct 1, 2019•0 citations

Measurement of loss in superconducting microstrip at millimeter-wave frequencies

Jiansong Gao, Anastasios Vayonakis, Omid Noroozian +6 more

We have developed a new technique for accurate measurement of the loss of superconducting microstrips at mm‐wave frequencies. In this technique, we optically couple power to slot antenna, which is connected to one port of a hybrid coupler. One of the output ports of the hybrid delivers power to a series of mm‐wave microstrip resonators which are capacitively coupled to a feedline followed by an MKID (microwave kinetic inductance detector) that measures the transmitted power. Two other MKIDs are connected to the remaining ports of the hybrid to measure the total incident optical power and the power reflected from the mm‐wave resonators, allowing |S21|2 and |S11|2 to be accurately determined and resonance frequency fr and quality factor Q to be retrieved. We have fabricated such a Nb/SiO2/Nb microstrip loss test device which contains several mm‐ wave resonators with fr∼100 GHz and measured it at 30 mK. All the resonators have shown internal quality factor Qi∼500–2000, suggesting a loss tangent of ∼5×10−4−2×10−3 for the SiO2 in use. For comparison, we have also fabricated a 5 GHz microstrip resonator on the same chip and measured it with a network analyzer. The loss tangent at 5 GHz derived from fitting the f0 and Q data to the two‐level system (TLS) model is 6×10−4, about the same as from the mm‐wave measurement. This suggests that the loss at both microwave and mm‐wave frequencies is probably dominated by the TLS in SiO2. Our results are of direct interest to mm/submm direct detection applications which use microstrip transmission lines (such as antenna‐coupled MKIDs and transition‐edge sensors), and other applications (such as on‐chip filters). Our measurement technique is applicable up to approximately 1 THz and can be used to investigate a range of dielectrics.

AIP conference proceedings•Jan 1, 2009•14 citations

Characterization of NB and TiN superconducting CPW lines with thru-line calibration method

Wei-Tao Lv, Jie Hu, Jing-Pin Yang +2 more

Microwave kinetic inductance detectors (MKIDs) are playing an increasingly role in THz astronomy. Superconducting coplanar waveguide (CPW) lines are commonly adopted in MKIDs for the resonators as well as the readout through line. It is therefore of particular interest to characterize the transmission properities of superconducting CPW lines at low temperatures. A cryogenic through-line method based on two cryogenic RF switches is proposed to characterize Nb and TiN superconducting CPW lines. On-chip calibration has been successfully carried out. Detailed results and analysis will be presented.

Infrared, Millimeter-Wave, and Terahertz Technologies•Nov 9, 2018•0 citations
We present a lab-on-chip technique to measure the very low losses in superconducting transmission lines at (sub-) mm wavelengths. The chips consist of a 100 nm-thick NbTiN Co-planar Waveguide (CPW) Fabry–Pérot (FP) resonator, coupled, on one side, to an antenna and, on the other side, to a Microwave Kinetic Inductance detector. Using a single frequency radiation source allows us to measure the frequency response of the FP around 350 GHz and deduce its losses. We show that the loss is dominated by radiation loss inside the CPW line that forms the FP and that it decreases with the decreasing linewidth and increasing kinetic inductance as expected. The results can be quantitatively understood using SONNET simulations. The lowest loss is observed for a CPW with a total width of 6 μm and corresponds to a Q-factor of ≈15 000.
We present results from completely lithographic antenna-coupled Microwave Kinetic Inductance detectors (MKIDs). MKIDs are superconducting resonators with resonant frequency and quality-factor which are highly sensitive to changes in the density of the quasiparticle population which occurs when photons above the superconducting gap energy are absorbed. The resonators are coupled to submm light through on-chip phased-array slot antennas. Each planar antenna consists of an array of N long slots which are fed along their length at M points. The resulting N*M feed points are combined in-phase using a binary summing tree made of low-loss superconducting microstrip lines. Due to its large size, the resulting planar antenna produces a narrow beam pattern and can therefore be used without additional optical coupling elements such as feedhorns or substrate lenses. The output of the antenna is a single superconducting thin-film microstrip line which can be efficiently coupled to one (or more) kinetic inductance coplanar waveguide resonators to produce a single (or multi-color) pixel in an imaging focal plane array, using in-line lumped element lithographic band-pass filters. Such highly integrated architectures can be easily fabricated on a single substrate, and many detectors can be frequency multiplexed through coupling to a single feedline. Microwave readout provides a lot of bandwidth per detector, allowing a large number of pixels to be read using a single cryogenic microwave amplifier and warm readout electronics.
Space-based astronomy is in need of a photon-noise limited detector with multiplexing opportunities. The kinetic inductance detector (KID) is capable of both properties. An incoming photon breaks Cooper pairs in the superconducting layer of the KID, which leads to a change in inductance, which can be detected with phase- and amplitude read-out. Photon noise, generation-recombination noise are inevitable noise sources, but two-level system noise can be minimized by adjusting the resonator and its geometry. To gain insight in the noise and loss sources this thesis investigates the difference between microstrip and co-planar waveguide resonators; and the difference between a silicon substrate and a silicon-on-insulator substrate. Numerical analysis shows that: noise in all types of resonators are dielectric bulk dominated; an Al superconducting layer shows has different losses in terms of Q-factor, compared to a NbTiN superconducting layer, but quantitatively the same internal Q-factor in the order of 105 is achieved; an Al superconducting layer in a microstrip has 5dBc/Hz and 2dBc/Hz higher noise in the metal-air and metal-edge interfaces, respectively, compared to a NbTiN superconducting layer; an Al on Si CPW and microstrip have the same Q-factor performance; an Al on Si CPW has a 2-8dBc/Hz more noise at all interfaces compared to an Al on Si microstrip; a buried oxide layer has no influence on the loss in terms of the Q-factor for 100nm Al on Si substrate CPWs; and that the noise of an Al on SOI CPW is bulk dominated, and the dielectric bulk contributes 10dBc/Hz more to the noise, compared to an Al on Si CPW. Experimental analysis shows that a gapwidth of wgap ? 10?m for Al on SOI CPWs shows no response, due to high two-level system noise. Low Q-factors in the order of 104 have been measured for Al on SOI CPWs, which is low compared to literature. A high set-up noise of -85dBc/Hz and divergent relationships with the internal power indicate that TLS-noise does not dominate the measurements, and set-up negatively influences the measurements. In conclusion, the resonator geometry is an important factor for the performance of a KID in terms of noise and Q-factors. A buried oxide layer has no consequence for the Q-factor, and negatively affects the noise of a CPW.
The sensitivity of a kinetic inductance detector is determined by the performance of the cavity circuit and therefore a high quality factor and low phase noise are required. We developed superconducting niobium coplanar waveguide resonators for kinetic inductance detectors at a resonance frequency of 6 GHz. The length of the resonators is adjusted to a quarter of a wavelength which corresponds to ≈ 5.3 mm in our geometry. Different layouts with coplanar waveguide transmission line topology for the resonator were designed and simulated. Some parameters of the device fabrication process were varied. The niobium thin films were deposited by magnetron sputtering on sapphire substrates kept at ambient temperature. The resonators were patterned by photolithography and reactive ion etching and measured at helium temperatures. Because of the quarter wave geometry with one shorted end the reflection parameter was measured. We have studied the influence of the coupling capacitances on quality factor. The optimization includes microwave simulations and implementation in different resonator structures. The measurements of optimized devices showed a very high quality factor above one million (10 6 ). The obtained results and perspective on further development of resonators will be discussed.
Microwave kinetic inductance detectors (MKID) are superconducting broadband direct detectors. If a superconducting thin film patterned into a resonator is illuminated with photons, Cooper pairs break up and the kinetic inductance of the film changes. This shifts the resonance frequency downwards and the dissipation of the resonator increases, which can be detected in the phase and amplitude of a transmitted signal. \n \nIn this thesis, a waveguide coupled MKID is designed and simulated. 350 GHz radiation is coupled into a copper waveguide via a horn antenna. A waveguide probe leads the signal onto a 9 µm silicon membrane where it is absorbed in a 40 nm superconducting aluminum film which is the inductive part of a superconducting resonator. The capacitor of the resonator is made of niobium. Two versions of the device are developed, a transmission line resonator and a lumped element resonator design. The new design will enable an accurate understanding of the optical sensitivity of MKIDs and allow comparison of different resonator materials. Since two different resonator types are used, the direct comparison of transmission line and lumped resonators will also be possible. \n \nA measurement setup is developed including an ADR cryostat to cool MKID devices down to below 40 mK. An analog readout system using either a vector network analyzer or an IQ mixer is designed and built. The necessary software to control the ADR, the temperature monitoring, the readout signal generation and detection and the signal acquisition of the setup is also developed. \n \nThe waveguide coupled MKID design is fabricated in our in-house microfabrication laboratory and measured in the new setup. In my measurements, the devices do not show a resonance feature. The VNA and DC measurements are analyzed to determine a plausible hypothesis of the failure. The devices are diagnosed for critical issues during fabrication which will be addressed in a future iteration. \n \nTo verify the measurement setup, a test device of the IRAM NIKA 2 MKID camera is measured and the complete analysis pipeline is exercised. The quasi-particle lifetime in the aluminum thin films is measured and a dark and optical noise equivalent power are determined. The results are within the uncertainty comparable to measurements of IRAM themselves. \n \nA test chip designed in my master thesis that contains eight NbTiN resonators is measured in the new setup and non-linear effects under strong readout power are studied. Parametric amplification and oscillation of a resonator are shown qualitatively.
We have developed a new technique for accurate measurement of the loss of superconducting microstrips at mm‐wave frequencies. In this technique, we optically couple power to slot antenna, which is connected to one port of a hybrid coupler. One of the output ports of the hybrid delivers power to a series of mm‐wave microstrip resonators which are capacitively coupled to a feedline followed by an MKID (microwave kinetic inductance detector) that measures the transmitted power. Two other MKIDs are connected to the remaining ports of the hybrid to measure the total incident optical power and the power reflected from the mm‐wave resonators, allowing |S21|2 and |S11|2 to be accurately determined and resonance frequency fr and quality factor Q to be retrieved. We have fabricated such a Nb/SiO2/Nb microstrip loss test device which contains several mm‐ wave resonators with fr∼100 GHz and measured it at 30 mK. All the resonators have shown internal quality factor Qi∼500–2000, suggesting a loss tangent of ∼5×10−4−2×10−3 for the SiO2 in use. For comparison, we have also fabricated a 5 GHz microstrip resonator on the same chip and measured it with a network analyzer. The loss tangent at 5 GHz derived from fitting the f0 and Q data to the two‐level system (TLS) model is 6×10−4, about the same as from the mm‐wave measurement. This suggests that the loss at both microwave and mm‐wave frequencies is probably dominated by the TLS in SiO2. Our results are of direct interest to mm/submm direct detection applications which use microstrip transmission lines (such as antenna‐coupled MKIDs and transition‐edge sensors), and other applications (such as on‐chip filters). Our measurement technique is applicable up to approximately 1 THz and can be used to investigate a range of dielectrics.
Microwave kinetic inductance detectors (MKIDs) are playing an increasingly role in THz astronomy. Superconducting coplanar waveguide (CPW) lines are commonly adopted in MKIDs for the resonators as well as the readout through line. It is therefore of particular interest to characterize the transmission properities of superconducting CPW lines at low temperatures. A cryogenic through-line method based on two cryogenic RF switches is proposed to characterize Nb and TiN superconducting CPW lines. On-chip calibration has been successfully carried out. Detailed results and analysis will be presented.