Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1910.09614 · Applied Physics Letters

Demonstration of a superconducting nanowire microwave switch

A. Wagner, Leonardo Ranzani, G. Ribeill, T. A. Ohki

Published Oct 21, 2019• 23 citations
arXivHTMLPDF

Abstract

The functionality of a nanowire integrated into a superconducting transmission line acting as a single pole single throw switch is demonstrated. The switch has an instantaneous bandwidth from 2 to 8 GHz with more than 10 dB of isolation between the open and closed states. The switch consumes no power in the closed state and ≈15 nW in the open state. The rise and fall response time between open and closed states is approximately 370 ps.

DOI
10.1063/1.5120009

Related papers

On-chip Josephson junction microwave switch

Ofer Naaman, Mohamed Abutaleb, Christopher F. Kirby +1 more

The authors report on the design and measurement of a reflective single-pole single-throw microwave switch with no internal power dissipation, based on a superconducting circuit containing a single Josephson junction. The data demonstrate the switch operation with 2 GHz instantaneous bandwidth centered at 10 GHz, low insertion loss, and better than 20 dB on/off ratio. The switch's measured performance agrees well with simulations for input powers up to −100 dBm. An extension of the demonstrated circuit to implement a single-pole double-throw switch is shown in simulation.

arXiv:1512.01484•Applied Physics Letters•Mar 14, 2016•50 citations

A superconducting microwave switch

G.D. Poulin, Frank A. Hegmann, Jean Lachapelle +2 more

We describe a superconducting microwave switch. The switch comprises a tapering microwave transmission line which can he switched from a very low loss ON state to a high impedance OFF state with a DC voltage applied to the transmission line through a bias-tee. Switching is essentially thermal in nature, occurring due to the formation of a 'hot spot' in the transmission line. Thermal runaway is avoided through the use of voltage rather than current biasing. Once switched, the transmission line attenuates the applied microwave signal. An isolation of 20 dB is readily achievable. The intrinsic response time of the hot spot to applied microwave fields was estimated to be approximately 1 /spl mu/s by measuring the frequency dependence of the transmitted signal.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•5 citations

Superconducting Switch for Fast On-Chip Routing of Quantum Microwave Fields

Marek Pechal, Jean-Claude Besse, Mintu Mondal +3 more

For a quantum computer, switching a signal carried by single microwave photons is desirable in scaling up superconducting circuitry. The authors design and build such a switch, integrate it on a chip with a single-photon source, and prove that it works with nonclassical microwave input. Their device offers negligible heating, relatively large bandwidth, low nonlinearity, and single-pole double-throw switching in mere nanoseconds. It is well suited for applications where signal routing must be controlled by real-time feedback, as in multiplexing qubit control and readout, or distributing entanglement in quantum networks.

arXiv:1606.01031•Physical Review Applied•Aug 11, 2016•80 citations

Demonstration of Microwave Multiplexed Readout of DC-Biased Superconducting Nanowire Detectors

A. K. Sinclair, E. Schroeder, Di Zhu +5 more

Superconducting nanowires are widely used as sensitive single photon detectors with wide spectral coverage and high timing resolution. We describe a demonstration of an array of dc-biased superconducting nanowire single photon detectors read out with a microwave multiplexing circuit. In this design, each individual nanowire is part of a resonant LC circuit where the inductance is dominated by the kinetic inductance of the nanowire. The circuit also contains two parallel plate capacitors, one of them is in parallel with the inductor and the other is coupled to a microwave transmission line that carries the signals to a cryogenic low-noise amplifier. All of the nanowires are connected via resistors to a single dc bias line that enables the nanowires to be current biased close to their critical current. When a photon hits a nanowire, it creates a normal hotspot that produces a voltage pulse across the LC circuit. This pulse rings down at the resonant frequency of the LC circuit over a time period that is fixed by the quality factor. We present measurements of an array of these devices and an evaluation of their performance in terms of frequency and time response.

arXiv:1905.06880•IEEE Transactions on Applied Superconductivity•Mar 8, 2019•26 citations

Demonstration of Microwave Multiplexed Readout of DC-Biased Superconducting Nanowire Detectors

Sinclair, AK, Schroeder, E, Di Zhu +5 more

© 2002-2011 IEEE. Superconducting nanowires are widely used as sensitive single photon detectors with wide spectral coverage and high timing resolution. We describe a demonstration of an array of dc-biased superconducting nanowire single photon detectors read out with a microwave multiplexing circuit. In this design, each individual nanowire is part of a resonant LC circuit where the inductance is dominated by the kinetic inductance of the nanowire. The circuit also contains two parallel plate capacitors, one of them is in parallel with the inductor and the other is coupled to a microwave transmission line that carries the signals to a cryogenic low-noise amplifier. All of the nanowires are connected via resistors to a single dc bias line that enables the nanowires to be current biased close to their critical current. When a photon hits a nanowire, it creates a normal hotspot that produces a voltage pulse across the LC circuit. This pulse rings down at the resonant frequency of the LC circuit over a time period that is fixed by the quality factor. We present measurements of an array of these devices and an evaluation of their performance in terms of frequency and time response.

•Jan 1, 2019•14 citations

Microwave Switch Architecture for Superconducting Integrated Circuits Using Magnetic Field-Tunable Josephson Junctions

A. L. Graninger, J. M. Cochran, Aaron A. Pesetski +5 more

We report on the design, fabrication, and measurement of a low-temperature microwave switch architecture that can be fully integrated on chip using single Josephson junctions and superconducting bias lines. The basic switching element used is a reflective single-pole-single-throw switch that is realized by tuning the critical current of a single Josephson junction by way of a local flux bias. A single-pole-single-throw switch is demonstrated at 4.2 K to have anon/offratio in excess of 20 dB up to 12 GHz. This element is then incorporated into the design of a single-pole-double-throw switch that exhibits anon/offratio above 20 dB up to 10 GHz. The switches require no intrinsic power dissipation in either state, and their performance was verified for input powers of$-$100 to$-$60 dBm. S-parameter simulations using a simple lumped element model are in good agreement with the experimental data, allowing for the design to be extended to larger switch architectures.

IEEE Transactions on Applied Superconductivity•Apr 20, 2023•6 citations
The functionality of a nanowire integrated into a superconducting transmission line acting as a single pole single throw switch is demonstrated. The switch has an instantaneous bandwidth from 2 to 8 GHz with more than 10 dB of isolation between the open and closed states. The switch consumes no power in the closed state and ≈15 nW in the open state. The rise and fall response time between open and closed states is approximately 370 ps.
The authors report on the design and measurement of a reflective single-pole single-throw microwave switch with no internal power dissipation, based on a superconducting circuit containing a single Josephson junction. The data demonstrate the switch operation with 2 GHz instantaneous bandwidth centered at 10 GHz, low insertion loss, and better than 20 dB on/off ratio. The switch's measured performance agrees well with simulations for input powers up to −100 dBm. An extension of the demonstrated circuit to implement a single-pole double-throw switch is shown in simulation.
We describe a superconducting microwave switch. The switch comprises a tapering microwave transmission line which can he switched from a very low loss ON state to a high impedance OFF state with a DC voltage applied to the transmission line through a bias-tee. Switching is essentially thermal in nature, occurring due to the formation of a 'hot spot' in the transmission line. Thermal runaway is avoided through the use of voltage rather than current biasing. Once switched, the transmission line attenuates the applied microwave signal. An isolation of 20 dB is readily achievable. The intrinsic response time of the hot spot to applied microwave fields was estimated to be approximately 1 /spl mu/s by measuring the frequency dependence of the transmitted signal.>
For a quantum computer, switching a signal carried by single microwave photons is desirable in scaling up superconducting circuitry. The authors design and build such a switch, integrate it on a chip with a single-photon source, and prove that it works with nonclassical microwave input. Their device offers negligible heating, relatively large bandwidth, low nonlinearity, and single-pole double-throw switching in mere nanoseconds. It is well suited for applications where signal routing must be controlled by real-time feedback, as in multiplexing qubit control and readout, or distributing entanglement in quantum networks.
Superconducting nanowires are widely used as sensitive single photon detectors with wide spectral coverage and high timing resolution. We describe a demonstration of an array of dc-biased superconducting nanowire single photon detectors read out with a microwave multiplexing circuit. In this design, each individual nanowire is part of a resonant LC circuit where the inductance is dominated by the kinetic inductance of the nanowire. The circuit also contains two parallel plate capacitors, one of them is in parallel with the inductor and the other is coupled to a microwave transmission line that carries the signals to a cryogenic low-noise amplifier. All of the nanowires are connected via resistors to a single dc bias line that enables the nanowires to be current biased close to their critical current. When a photon hits a nanowire, it creates a normal hotspot that produces a voltage pulse across the LC circuit. This pulse rings down at the resonant frequency of the LC circuit over a time period that is fixed by the quality factor. We present measurements of an array of these devices and an evaluation of their performance in terms of frequency and time response.
© 2002-2011 IEEE. Superconducting nanowires are widely used as sensitive single photon detectors with wide spectral coverage and high timing resolution. We describe a demonstration of an array of dc-biased superconducting nanowire single photon detectors read out with a microwave multiplexing circuit. In this design, each individual nanowire is part of a resonant LC circuit where the inductance is dominated by the kinetic inductance of the nanowire. The circuit also contains two parallel plate capacitors, one of them is in parallel with the inductor and the other is coupled to a microwave transmission line that carries the signals to a cryogenic low-noise amplifier. All of the nanowires are connected via resistors to a single dc bias line that enables the nanowires to be current biased close to their critical current. When a photon hits a nanowire, it creates a normal hotspot that produces a voltage pulse across the LC circuit. This pulse rings down at the resonant frequency of the LC circuit over a time period that is fixed by the quality factor. We present measurements of an array of these devices and an evaluation of their performance in terms of frequency and time response.
We report on the design, fabrication, and measurement of a low-temperature microwave switch architecture that can be fully integrated on chip using single Josephson junctions and superconducting bias lines. The basic switching element used is a reflective single-pole-single-throw switch that is realized by tuning the critical current of a single Josephson junction by way of a local flux bias. A single-pole-single-throw switch is demonstrated at 4.2 K to have anon/offratio in excess of 20 dB up to 12 GHz. This element is then incorporated into the design of a single-pole-double-throw switch that exhibits anon/offratio above 20 dB up to 10 GHz. The switches require no intrinsic power dissipation in either state, and their performance was verified for input powers of$-100to100 to100to-$60 dBm. S-parameter simulations using a simple lumped element model are in good agreement with the experimental data, allowing for the design to be extended to larger switch architectures.