Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1801.06265 · Journal of Low Temperature Physics

Design and Performance of the Antenna-Coupled Lumped-Element Kinetic Inductance Detector

Peter S. Barry, S. Doyle, Amber L. Hornsby, Anna M. Kofman, E. Mayer, A. Nadolski, Q. Y. Tang, J. Vieira, Erik D. Shirokoff

Published May 11, 2018• 10 citations
arXivHTMLPDF

Abstract

Focal plane arrays consisting of low-noise, polarisation-sensitive detectors have made possible the pioneering advances in the study of the cosmic microwave background (CMB). To make further progress, the next generation of CMB experiments (e.g. CMB-S4) will require a substantial increase in the number of detectors compared to current instruments. Arrays of kinetic inductance detectors (KIDs) provide a possible path to realising such large-format arrays owing to their intrinsic multiplexing advantage and relative cryogenic simplicity. In this paper, we report on the design of a variant of the traditional KID design: the antenna-coupled lumped-element KID. A polarisation-sensitive twin-slot antenna placed behind an optimised hemispherical lens couples power onto a thin-film superconducting microstrip line. The power is then guided into the inductive section of an aluminium KID, where it is absorbed and modifies both the resonant frequency and quality factor of the KID. We present the various aspects of the design and preliminary results from the first set of seven-element prototype arrays and compare to the expected modelled performance.

DOI
10.1007/s10909-018-1943-y

Related papers

Antenna-coupled lumped-element ALD titanium nitride KIDs for CMB instruments (Conference Presentation)

Erik D. Shirokoff, Peter S. Barry, Q. Y. Tang +1 more

Future ground-based cosmic microwave background (CMB) experiments will require more than $10^5$ polarization sensitive pixels covering multiple atmospheric bands. The scientific potential for such an experiment is impressive; however, the technical challenges are daunting: such an instrument will require square meters of focal plane covered in background limited cryogenic detectors and a dramatic increase in readout capability. We are developing novel kinetic inductance detectors (KIDs) optimized for this purpose. These devices use a twin-slot microwave antenna, superconducting Nb transmission line, and a novel coupling scheme that deposits mm-wavelength power onto a high-resistivity meander deposited as the first layer on a bare Si wafer. This architecture allows us to independently adjust the detector and antenna properties and to pursue multi-band designs. We have fabricated superconducting resonators made from atomic layer deposited (ALD) titanium nitride (TiN), with thicknesses ranging from 3 to 40 nm. We find a strong dependence of transition temperature on thickness, from 0.6 to 4.2 K for our thinnest and thickest films, respectively. In dark measurements, we find internal quality factors that range from $10^4$ to $7\times 10^5$ depending on film thickness, and kinetic inductance as high as 8 nH/square. The very small volumes and high kinetic inductance make it possible to engineer extremely sensitive detectors with inductor volumes approaching a few cubic microns that operate at readout frequencies of tens to hundreds of MHz. By taking advantage of the large fractional bandwidth available at low frequencies, we expect to achieve multiplexing densities that exceed that of state of the art TES arrays even without further improvements in film quality factor. We will present the characterization of film properties and dark devices, as well as well as initial optical results for antenna coupled single-band and single-pol devices. We will also discuss designs and sensitivity projections for future dual-pol and multi-band arrays ready for deployment in near-future CMB instruments.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Jul 10, 2018•0 citations

Kinetic inductance detectors for measuring the polarization of the cosmic microwave background

D. Flanigan

Kinetic inductance detectors (KIDs) are superconducting thin-film microresonators that are sensitive photon detectors. These detectors are a candidate for the next generation of experiments designed to measure the polarization of the cosmic microwave background (CMB). I discuss the basic theory needed to understand the response of a KID to light, focusing on the dynamics of the quasiparticle system. I derive an equation that describes the dynamics of the quasiparticle number, solve it in a simplified form not previously published, and show that it can describe the dynamic response of a detector. Magnetic flux vortices in a superconducting thin film can be a significant source of dissipation, and I demonstrate some techniques to prevent their formation. Based on the presented theory, I derive a corrected version of a widely-used equation for the quasiparticle recombination noise in a KID. I show that a KID consisting of a lumped-element resonator can be sensitive enough to be limited by photon noise, which is the fundamental limit for photometry, at a level of optical loading below levels in ground-based CMB experiments. Finally, I describe an ongoing project to develop multichroic KID pixels that are each sensitive to two linear polarization states in two spectral bands, intended for the next generation of CMB experiments. I show that a prototype 23-pixel array can detect millimeter-wave light, and present characterization measurements of the detectors.

•Jan 1, 2018•1 citation

A Lumped Element Kinetic Inductance device for detection of THz radiation

Simon M. Doyle, Philip D. Mauskopf, C. Dunscombe +2 more

Kinetic inductance detectors (KIDs) provide a promising solution to the problem of producing large format arrays of ultra sensitive detectors for astronomy. Traditionally KIDs have been constructed from superconducting quarter-wavelength or half-wavelength resonator elements capacitively coupled to a co-planar feed line. Photons are detected by measuring the change in quasi-particle density caused by the splitting of Cooper pairs in the superconducting resonant element. This change in quasi-particle density alters the kinetic inductance, and hence the resonant frequency of the resonant element. This arrangement requires the quasi-particles generated by photon absorption to be concentrated at positions of high current density in the resonator. This is usually achieved through antenna coupling or quasi-particle trapping. For these detectors to work at wavelengths shorter than around 500 mum where antenna coupling can introduce a significant loss of efficiency, then a direct absorption method needs to be considered [3]. One solution to this problem is the Lumped Element KID (LEKID), which shows no current variation along its length and can be arranged into a photon absorbing area coupled to free space and therefore requiring no antennas or quasi-particle trapping. This paper outlines the basic concept of the LEKID, along with theoretical performance and experimental data for these devices.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Sep 1, 2007•6 citations

Antenna-coupled Microwave Kinetic Inductance detectors (MKIDs) for mm and submm imaging arrays

Anastasios Vayonakis, James A. Schlaerth, S. Kumar +9 more

We present results from completely lithographic antenna-coupled Microwave Kinetic Inductance detectors (MKIDs). MKIDs are superconducting resonators with resonant frequency and quality-factor which are highly sensitive to changes in the density of the quasiparticle population which occurs when photons above the superconducting gap energy are absorbed. The resonators are coupled to submm light through on-chip phased-array slot antennas. Each planar antenna consists of an array of N long slots which are fed along their length at M points. The resulting N*M feed points are combined in-phase using a binary summing tree made of low-loss superconducting microstrip lines. Due to its large size, the resulting planar antenna produces a narrow beam pattern and can therefore be used without additional optical coupling elements such as feedhorns or substrate lenses. The output of the antenna is a single superconducting thin-film microstrip line which can be efficiently coupled to one (or more) kinetic inductance coplanar waveguide resonators to produce a single (or multi-color) pixel in an imaging focal plane array, using in-line lumped element lithographic band-pass filters. Such highly integrated architectures can be easily fabricated on a single substrate, and many detectors can be frequency multiplexed through coupling to a single feedline. Microwave readout provides a lot of bandwidth per detector, allowing a large number of pixels to be read using a single cryogenic microwave amplifier and warm readout electronics.

Softwaretechnik-Trends•Apr 1, 2008•1 citation

Kinetic inductance detectors for 200μm astronomy

Simon M. Doyle, Jack Alexander Naylon, James Cox +2 more

Kinetic inductance detectors (KIDs) provide an attractive solution to the production of large detector arrays for use in ground and space based 200μm astronomy. KIDs work by measuring the change in quasi-particle density upon photon absorption in a high Q superconducting resonator. A change in quasi-particle density is measured by a shift in phase of a microwave probe signal of frequency equal to that of the resonant frequency of the KID. Such detectors have a fundamental noise limit owing to the quasi-particle recombination rate, which, in a KID fabricated from a high quality Niobium film can give sensitivities of 10-18W√Hz at 1K. Constructing KIDs of varying resonant frequencies coupled to a single transmission line provides a multiplexed detector array with simple low temperature electronics. Here we discuss the theoretical requirements for both ground and space based 200μm cameras with various radiation coupling schemes for this wavelength range using distributed and lumped element high Q resonators.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 14, 2006•4 citations

Characterization of distributed and lumped-element THz MKIDs

Wei-Tao Lv, Liang-si Zhou, Jing Li +2 more

Microwave Kinetic Inductance Detectors (MKIDs), just like a planar resonance cavity resonating at a microwave frequency, are emerging as a kind of high-sensitivity detector suitable for large format arrays at terahertz (THz) wavelengths. There are two types of MKIDs, namely distributed (or antenna-coupled) MKIDs and lumped-element MKIDs (aka LeKIDs). Various superconducting thin films (such as Al, TiN, NbTiN, NbN, and Nb) have been investigated for MKIDs. They do work so long as the detected photon energy exceeds their energy gap, but their response and noise behaviors are yet to be fully understood. Here we report on the design, fabrication, and characterization of distributed and lumped-element MKIDs made of NbTiN superconducting film. Detailed simulation and measurement results will be presented.

•Nov 24, 2021•0 citations
Focal plane arrays consisting of low-noise, polarisation-sensitive detectors have made possible the pioneering advances in the study of the cosmic microwave background (CMB). To make further progress, the next generation of CMB experiments (e.g. CMB-S4) will require a substantial increase in the number of detectors compared to current instruments. Arrays of kinetic inductance detectors (KIDs) provide a possible path to realising such large-format arrays owing to their intrinsic multiplexing advantage and relative cryogenic simplicity. In this paper, we report on the design of a variant of the traditional KID design: the antenna-coupled lumped-element KID. A polarisation-sensitive twin-slot antenna placed behind an optimised hemispherical lens couples power onto a thin-film superconducting microstrip line. The power is then guided into the inductive section of an aluminium KID, where it is absorbed and modifies both the resonant frequency and quality factor of the KID. We present the various aspects of the design and preliminary results from the first set of seven-element prototype arrays and compare to the expected modelled performance.
Future ground-based cosmic microwave background (CMB) experiments will require more than 10510^5105 polarization sensitive pixels covering multiple atmospheric bands. The scientific potential for such an experiment is impressive; however, the technical challenges are daunting: such an instrument will require square meters of focal plane covered in background limited cryogenic detectors and a dramatic increase in readout capability. We are developing novel kinetic inductance detectors (KIDs) optimized for this purpose. These devices use a twin-slot microwave antenna, superconducting Nb transmission line, and a novel coupling scheme that deposits mm-wavelength power onto a high-resistivity meander deposited as the first layer on a bare Si wafer. This architecture allows us to independently adjust the detector and antenna properties and to pursue multi-band designs. We have fabricated superconducting resonators made from atomic layer deposited (ALD) titanium nitride (TiN), with thicknesses ranging from 3 to 40 nm. We find a strong dependence of transition temperature on thickness, from 0.6 to 4.2 K for our thinnest and thickest films, respectively. In dark measurements, we find internal quality factors that range from 10410^4104 to 7×1057\times 10^57×105 depending on film thickness, and kinetic inductance as high as 8 nH/square. The very small volumes and high kinetic inductance make it possible to engineer extremely sensitive detectors with inductor volumes approaching a few cubic microns that operate at readout frequencies of tens to hundreds of MHz. By taking advantage of the large fractional bandwidth available at low frequencies, we expect to achieve multiplexing densities that exceed that of state of the art TES arrays even without further improvements in film quality factor. We will present the characterization of film properties and dark devices, as well as well as initial optical results for antenna coupled single-band and single-pol devices. We will also discuss designs and sensitivity projections for future dual-pol and multi-band arrays ready for deployment in near-future CMB instruments.
Kinetic inductance detectors (KIDs) are superconducting thin-film microresonators that are sensitive photon detectors. These detectors are a candidate for the next generation of experiments designed to measure the polarization of the cosmic microwave background (CMB). I discuss the basic theory needed to understand the response of a KID to light, focusing on the dynamics of the quasiparticle system. I derive an equation that describes the dynamics of the quasiparticle number, solve it in a simplified form not previously published, and show that it can describe the dynamic response of a detector. Magnetic flux vortices in a superconducting thin film can be a significant source of dissipation, and I demonstrate some techniques to prevent their formation. Based on the presented theory, I derive a corrected version of a widely-used equation for the quasiparticle recombination noise in a KID. I show that a KID consisting of a lumped-element resonator can be sensitive enough to be limited by photon noise, which is the fundamental limit for photometry, at a level of optical loading below levels in ground-based CMB experiments. Finally, I describe an ongoing project to develop multichroic KID pixels that are each sensitive to two linear polarization states in two spectral bands, intended for the next generation of CMB experiments. I show that a prototype 23-pixel array can detect millimeter-wave light, and present characterization measurements of the detectors.
Kinetic inductance detectors (KIDs) provide a promising solution to the problem of producing large format arrays of ultra sensitive detectors for astronomy. Traditionally KIDs have been constructed from superconducting quarter-wavelength or half-wavelength resonator elements capacitively coupled to a co-planar feed line. Photons are detected by measuring the change in quasi-particle density caused by the splitting of Cooper pairs in the superconducting resonant element. This change in quasi-particle density alters the kinetic inductance, and hence the resonant frequency of the resonant element. This arrangement requires the quasi-particles generated by photon absorption to be concentrated at positions of high current density in the resonator. This is usually achieved through antenna coupling or quasi-particle trapping. For these detectors to work at wavelengths shorter than around 500 mum where antenna coupling can introduce a significant loss of efficiency, then a direct absorption method needs to be considered [3]. One solution to this problem is the Lumped Element KID (LEKID), which shows no current variation along its length and can be arranged into a photon absorbing area coupled to free space and therefore requiring no antennas or quasi-particle trapping. This paper outlines the basic concept of the LEKID, along with theoretical performance and experimental data for these devices.
We present results from completely lithographic antenna-coupled Microwave Kinetic Inductance detectors (MKIDs). MKIDs are superconducting resonators with resonant frequency and quality-factor which are highly sensitive to changes in the density of the quasiparticle population which occurs when photons above the superconducting gap energy are absorbed. The resonators are coupled to submm light through on-chip phased-array slot antennas. Each planar antenna consists of an array of N long slots which are fed along their length at M points. The resulting N*M feed points are combined in-phase using a binary summing tree made of low-loss superconducting microstrip lines. Due to its large size, the resulting planar antenna produces a narrow beam pattern and can therefore be used without additional optical coupling elements such as feedhorns or substrate lenses. The output of the antenna is a single superconducting thin-film microstrip line which can be efficiently coupled to one (or more) kinetic inductance coplanar waveguide resonators to produce a single (or multi-color) pixel in an imaging focal plane array, using in-line lumped element lithographic band-pass filters. Such highly integrated architectures can be easily fabricated on a single substrate, and many detectors can be frequency multiplexed through coupling to a single feedline. Microwave readout provides a lot of bandwidth per detector, allowing a large number of pixels to be read using a single cryogenic microwave amplifier and warm readout electronics.
Kinetic inductance detectors (KIDs) provide an attractive solution to the production of large detector arrays for use in ground and space based 200μm astronomy. KIDs work by measuring the change in quasi-particle density upon photon absorption in a high Q superconducting resonator. A change in quasi-particle density is measured by a shift in phase of a microwave probe signal of frequency equal to that of the resonant frequency of the KID. Such detectors have a fundamental noise limit owing to the quasi-particle recombination rate, which, in a KID fabricated from a high quality Niobium film can give sensitivities of 10-18W√Hz at 1K. Constructing KIDs of varying resonant frequencies coupled to a single transmission line provides a multiplexed detector array with simple low temperature electronics. Here we discuss the theoretical requirements for both ground and space based 200μm cameras with various radiation coupling schemes for this wavelength range using distributed and lumped element high Q resonators.
Microwave Kinetic Inductance Detectors (MKIDs), just like a planar resonance cavity resonating at a microwave frequency, are emerging as a kind of high-sensitivity detector suitable for large format arrays at terahertz (THz) wavelengths. There are two types of MKIDs, namely distributed (or antenna-coupled) MKIDs and lumped-element MKIDs (aka LeKIDs). Various superconducting thin films (such as Al, TiN, NbTiN, NbN, and Nb) have been investigated for MKIDs. They do work so long as the detected photon energy exceeds their energy gap, but their response and noise behaviors are yet to be fully understood. Here we report on the design, fabrication, and characterization of distributed and lumped-element MKIDs made of NbTiN superconducting film. Detailed simulation and measurement results will be presented.