Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1707.03339 · Physical Review Letters

Spatially Adiabatic Frequency Conversion in Optoelectromechanical Arrays

Ondřej Černotík, Sahand Mahmoodian, Klemens Hammerer

Published Sep 14, 2018• 30 citations
arXivHTMLPDF

Abstract

Faithful conversion of quantum signals between microwave and optical frequency domains is crucial for building quantum networks based on superconducting circuits. Optoelectromechanical systems, in which microwave and optical cavity modes are coupled to a common mechanical oscillator, are a promising route towards this goal. In these systems, efficient, low-noise conversion is possible using a mechanically dark mode of the fields, but the conversion bandwidth is limited to a fraction of the cavity linewidth. Here, we show that an array of optoelectromechanical transducers can overcome this limitation and reach a bandwidth that is larger than the cavity linewidth. The coupling rates are varied in space throughout the array so that the mechanically dark mode of the propagating fields adiabatically changes from microwave to optical or vice versa. This strategy also leads to significantly reduced thermal noise with the collective optomechanical cooperativity being the relevant figure of merit. Finally, we demonstrate that the bandwidth enhancement is, surprisingly, largest for small arrays; this feature makes our scheme particularly attractive for state-of-the-art experimental setups.

DOI
10.1103/physrevlett.121.110506

Related papers

Microwave-to-optical transduction using coupled piezoelectric and optomechanical resonators

Marcelo Wu, Emil Zeuthen, Krishna C. Balram +1 more

The successes of superconducting quantum circuits at local manipulation of quantum information and photonics technology at long-distance transmission of the same have spurred interest in the development of quantum transducers for efficient, low-noise, and bidirectional frequency conversion of photons between the microwave and optical domains. We propose to realize such functionality through the coupling of electrical, piezoelectric, and optomechanical resonators. The coupling of the mechanical subsystems enables formation of a resonant mechanical supermode that provides a mechanically-mediated, efficient single interface to both the microwave and optical domains. The conversion process is analyzed by applying an equivalent circuit model that relates device-level parameters to overall figures of merit for conversion efficiency $\eta$ and added noise $N$. These can be further enhanced by proper impedance matching of the transducer to an input microwave transmission line. The performance of potential transducers is assessed through finite-element simulations, with a focus on geometries in GaAs, followed by considerations of the AlN, LiNbO$_3$, and AlN-on-Si platforms. We present strategies for maximizing $\eta$ and minimizing $N$, and find that simultaneously achieving $\eta>50~\%$ and $N < 0.5$ should be possible with current technology. Our comprehensive analysis of the full transduction chain enables us to outline a development path for the realization of high-performance quantum transducers that will constitute a new resource for quantum information science.

•Jul 10, 2019•1 citation

Enhanced Microwave-Optical Conversion Via Ancillary Electro-Mechanical Coupling

Tianli Wei, Dewei Wu, Qiang Miao +1 more

Converting signals from the microwave to the optical domain has attracted great attention due to its potential applications in the field of quantum networks. Achieving efficient transduction is a significant yet challenging task, where a high efficiency at single photon level and low added noise are required. Electro-opto-mechanics have been proven to be efficient to convert microwave and optical photons bidirectionally. In this work, we propose and demonstrate an enhanced microwave-optical conversion in an electro-opto-mechanical system by introducing a mechanical ancilla attached the microwave resonator. Based on the ancillary electromechanical coupling, the damping rate of the microwave resonator is controlled and further leads to significant enhancement in conversion, such as the increase of conversion efficiency, broadening of conversion bandwidth and reduction of added noise. It provides a feasible approach to realize a broadband microwave-optical conversion with high efficiency. Moreover, the reduced added noise may break the limitation of quantum transduction due to the ancillary electromechanical coupling. Our scheme is also applicable and feasible for opto-mechanics and other systems to achieve practical quantum interface.

Results in Physics•Jan 1, 2021•1 citation

Nonreciprocal quantum-state conversion between microwave and optical photons

Lin Tian, Zhen Li

Optoelectromechanical quantum interfaces can be utilized to connect systems with distinctively different frequencies in hybrid quantum networks. Here we present a scheme of nonreciprocal quantum-state conversion between microwave and optical photons via an optoelectromechanical interface. By introducing an auxiliary cavity and manipulating the phase differences between the linearized light-matter couplings, unidirectional state transmission that is immune to mechanical noise can be achieved. This interface can function as an isolator, a circulator, and a two-way switch that routes the input state to a designated output channel. We show that under a generalized impedance matching condition the state conversion can prevent thermal fluctuations of the mechanical mode from propagating to the cavity outputs and reach high fidelity. The realization of this scheme is also discussed.

arXiv:1610.09556•Physical Review A•Jul 7, 2017•71 citations

Microwave-to-Optical Transduction Using a Mechanical Supermode for Coupling Piezoelectric and Optomechanical Resonators

Marcelo Wu, Emil Zeuthen, Krishna C. Balram +1 more

The successes of superconducting quantum circuits at local manipulation of quantum information and photonics technology at long-distance transmission of the same have spurred interest in the development of quantum transducers for efficient, low-noise, and bidirectional frequency conversion of photons between the microwave and optical domains. We propose to realize such functionality through the coupling of electrical, piezoelectric, and optomechanical resonators. The coupling of the mechanical subsystems enables formation of a resonant mechanical supermode that provides a mechanically mediated, efficient single interface to both the microwave and optical domains. The conversion process is analyzed by applying an equivalent circuit model that relates device-level parameters to overall figures of merit for conversion efficiency $\ensuremath{\eta}$ and added noise $N$. These can be further enhanced by proper impedance matching of the transducer to an input microwave transmission line. The performance of potential transducers is assessed through finite-element simulations, with a focus on geometries in $\mathrm{Ga}\mathrm{As}$, followed by considerations of the $\mathrm{Al}\mathrm{N}$, ${\mathrm{Li}\mathrm{Nb}\mathrm{O}}_{3}$, and $\mathrm{Al}\mathrm{N}$-on-$\mathrm{Si}$ platforms. We present strategies for maximizing $\ensuremath{\eta}$ and minimizing $N$, and find that simultaneously achieving $\ensuremath{\eta}>50\mathrm{%}$ and $N<0.5$ should be possible with current technology. We find that the use of a mechanical supermode for mediating transduction is a key enabler for high-efficiency operation, particularly when paired with an appropriate microwave impedance-matching network. Our comprehensive analysis of the full transduction chain enables us to outline a development path for the realization of high-performance quantum transducers that will constitute a valuable resource for quantum information science.

arXiv:1907.04830•Physical Review Applied•Jan 16, 2020•74 citations

Enhanced Cooperativity in a Near-Quantum Microwave-To-Optical Transducer

Mittal, Sarang

One of the main thrusts of quantum science over the past few decades has been the developmentof quantum networks for the purposes of secure communication, enhanced detector sensitivity, and advanced computing. Realizing such a network of superconducting quantum processors that communicate via optical fibers would leverage the high-fidelity quantum signal processing of superconducting circuits and the thermal robustness of infrared light but requires a transducer capable of connecting these two sections of the electromagnetic spectrum separated by five orders of magnitude in energy. This thesis explores the optimization of a transducer architecture where the mechanical mode of a Si3N4 membrane mediates the coupling of a superconducting lumped element circuit and a Fabry-Perot optical cavity. We aim to maximize the coupling of these three harmonic oscillator to each other while shielding them from noisy processes that would decohere quantum signals. This architecture has led to transducers with unparalleled efficiency and continuous operation. Enhanced cooperativity between the optical cavity and mechanical oscillator enabled optically-detected readout of a superconducting qubit and optomechanical ground state cooling with negligible laser-induced heating of the superconducting qubit and microwave circuit. To surpass the threshold for quantum-enabled operation, we subsequently improved the cooperativity between the microwave circuit and mechanical oscillator by reducing the microwave loss and noise from two-level-system-like defects in the Si3N4 dielectric. When combined with enhanced coupling between the circuit and membrane or improved mechanical isolation, we project that this architecture will be capable of transducing quantum signals between the microwave and optical regimes with a signal-to-noise greater than one.

•Nov 20, 2024•0 citations

Nonreciprocal conversion between radio-frequency and optical photons with an optoelectromechanical system

Najmeh Eshaqi-Sani, Stefano Zippilli, David Vitali

Nonreciprocal systems breaking time-reversal symmetry are essential tools in modern quantum technologies enabling the suppression of unwanted reflected signals or extraneous noise entering through detection ports. Here we propose a scheme enabling nonreciprocal conversion between optical and radio-frequency (rf) photons using exclusively optomechanical and electromechanical interactions. The nonreciprocal transmission is obtained by interference of two dissipative pathways of transmission between the two electromagnetic modes established through two distinct intermediate mechanical modes. In our protocol, we apply a bichromatic drive to the cavity mode and a single-tone drive to the rf resonator, and use the relative phase between the drive tones to obtain nonreciprocity. We show that perfect nonreciprocal transduction can be obtained in the limit of large cooperativity in both directions, from optical to rf and vice versa. We also study the transducer noise and show that mechanical thermal noise is always reflected back onto the isolated port. In the limit of large cooperativity, the input noise is instead transmitted in an unaltered way in the allowed direction; in particular one has only vacuum noise in the output rf port in the case of optical-to-rf conversion.

arXiv:2202.13231•Physical Review A•Sep 7, 2022•17 citations
Faithful conversion of quantum signals between microwave and optical frequency domains is crucial for building quantum networks based on superconducting circuits. Optoelectromechanical systems, in which microwave and optical cavity modes are coupled to a common mechanical oscillator, are a promising route towards this goal. In these systems, efficient, low-noise conversion is possible using a mechanically dark mode of the fields, but the conversion bandwidth is limited to a fraction of the cavity linewidth. Here, we show that an array of optoelectromechanical transducers can overcome this limitation and reach a bandwidth that is larger than the cavity linewidth. The coupling rates are varied in space throughout the array so that the mechanically dark mode of the propagating fields adiabatically changes from microwave to optical or vice versa. This strategy also leads to significantly reduced thermal noise with the collective optomechanical cooperativity being the relevant figure of merit. Finally, we demonstrate that the bandwidth enhancement is, surprisingly, largest for small arrays; this feature makes our scheme particularly attractive for state-of-the-art experimental setups.
The successes of superconducting quantum circuits at local manipulation of quantum information and photonics technology at long-distance transmission of the same have spurred interest in the development of quantum transducers for efficient, low-noise, and bidirectional frequency conversion of photons between the microwave and optical domains. We propose to realize such functionality through the coupling of electrical, piezoelectric, and optomechanical resonators. The coupling of the mechanical subsystems enables formation of a resonant mechanical supermode that provides a mechanically-mediated, efficient single interface to both the microwave and optical domains. The conversion process is analyzed by applying an equivalent circuit model that relates device-level parameters to overall figures of merit for conversion efficiency η\etaη and added noise NNN. These can be further enhanced by proper impedance matching of the transducer to an input microwave transmission line. The performance of potential transducers is assessed through finite-element simulations, with a focus on geometries in GaAs, followed by considerations of the AlN, LiNbO3_33​, and AlN-on-Si platforms. We present strategies for maximizing η\etaη and minimizing NNN, and find that simultaneously achieving η>50 %\eta>50~\%η>50 % and N<0.5N < 0.5N<0.5 should be possible with current technology. Our comprehensive analysis of the full transduction chain enables us to outline a development path for the realization of high-performance quantum transducers that will constitute a new resource for quantum information science.
Converting signals from the microwave to the optical domain has attracted great attention due to its potential applications in the field of quantum networks. Achieving efficient transduction is a significant yet challenging task, where a high efficiency at single photon level and low added noise are required. Electro-opto-mechanics have been proven to be efficient to convert microwave and optical photons bidirectionally. In this work, we propose and demonstrate an enhanced microwave-optical conversion in an electro-opto-mechanical system by introducing a mechanical ancilla attached the microwave resonator. Based on the ancillary electromechanical coupling, the damping rate of the microwave resonator is controlled and further leads to significant enhancement in conversion, such as the increase of conversion efficiency, broadening of conversion bandwidth and reduction of added noise. It provides a feasible approach to realize a broadband microwave-optical conversion with high efficiency. Moreover, the reduced added noise may break the limitation of quantum transduction due to the ancillary electromechanical coupling. Our scheme is also applicable and feasible for opto-mechanics and other systems to achieve practical quantum interface.
Optoelectromechanical quantum interfaces can be utilized to connect systems with distinctively different frequencies in hybrid quantum networks. Here we present a scheme of nonreciprocal quantum-state conversion between microwave and optical photons via an optoelectromechanical interface. By introducing an auxiliary cavity and manipulating the phase differences between the linearized light-matter couplings, unidirectional state transmission that is immune to mechanical noise can be achieved. This interface can function as an isolator, a circulator, and a two-way switch that routes the input state to a designated output channel. We show that under a generalized impedance matching condition the state conversion can prevent thermal fluctuations of the mechanical mode from propagating to the cavity outputs and reach high fidelity. The realization of this scheme is also discussed.
The successes of superconducting quantum circuits at local manipulation of quantum information and photonics technology at long-distance transmission of the same have spurred interest in the development of quantum transducers for efficient, low-noise, and bidirectional frequency conversion of photons between the microwave and optical domains. We propose to realize such functionality through the coupling of electrical, piezoelectric, and optomechanical resonators. The coupling of the mechanical subsystems enables formation of a resonant mechanical supermode that provides a mechanically mediated, efficient single interface to both the microwave and optical domains. The conversion process is analyzed by applying an equivalent circuit model that relates device-level parameters to overall figures of merit for conversion efficiency $\ensuremath{\eta}$ and added noise NNN. These can be further enhanced by proper impedance matching of the transducer to an input microwave transmission line. The performance of potential transducers is assessed through finite-element simulations, with a focus on geometries in GaAs\mathrm{Ga}\mathrm{As}GaAs, followed by considerations of the AlN\mathrm{Al}\mathrm{N}AlN, LiNbO3{\mathrm{Li}\mathrm{Nb}\mathrm{O}}_{3}LiNbO3​, and AlN\mathrm{Al}\mathrm{N}AlN-on-Si\mathrm{Si}Si platforms. We present strategies for maximizing $\ensuremath{\eta}$ and minimizing NNN, and find that simultaneously achieving $\ensuremath{\eta}>50\mathrm{%}$ and N<0.5N<0.5N<0.5 should be possible with current technology. We find that the use of a mechanical supermode for mediating transduction is a key enabler for high-efficiency operation, particularly when paired with an appropriate microwave impedance-matching network. Our comprehensive analysis of the full transduction chain enables us to outline a development path for the realization of high-performance quantum transducers that will constitute a valuable resource for quantum information science.
One of the main thrusts of quantum science over the past few decades has been the developmentof quantum networks for the purposes of secure communication, enhanced detector sensitivity, and advanced computing. Realizing such a network of superconducting quantum processors that communicate via optical fibers would leverage the high-fidelity quantum signal processing of superconducting circuits and the thermal robustness of infrared light but requires a transducer capable of connecting these two sections of the electromagnetic spectrum separated by five orders of magnitude in energy. This thesis explores the optimization of a transducer architecture where the mechanical mode of a Si3N4 membrane mediates the coupling of a superconducting lumped element circuit and a Fabry-Perot optical cavity. We aim to maximize the coupling of these three harmonic oscillator to each other while shielding them from noisy processes that would decohere quantum signals. This architecture has led to transducers with unparalleled efficiency and continuous operation. Enhanced cooperativity between the optical cavity and mechanical oscillator enabled optically-detected readout of a superconducting qubit and optomechanical ground state cooling with negligible laser-induced heating of the superconducting qubit and microwave circuit. To surpass the threshold for quantum-enabled operation, we subsequently improved the cooperativity between the microwave circuit and mechanical oscillator by reducing the microwave loss and noise from two-level-system-like defects in the Si3N4 dielectric. When combined with enhanced coupling between the circuit and membrane or improved mechanical isolation, we project that this architecture will be capable of transducing quantum signals between the microwave and optical regimes with a signal-to-noise greater than one.
Nonreciprocal systems breaking time-reversal symmetry are essential tools in modern quantum technologies enabling the suppression of unwanted reflected signals or extraneous noise entering through detection ports. Here we propose a scheme enabling nonreciprocal conversion between optical and radio-frequency (rf) photons using exclusively optomechanical and electromechanical interactions. The nonreciprocal transmission is obtained by interference of two dissipative pathways of transmission between the two electromagnetic modes established through two distinct intermediate mechanical modes. In our protocol, we apply a bichromatic drive to the cavity mode and a single-tone drive to the rf resonator, and use the relative phase between the drive tones to obtain nonreciprocity. We show that perfect nonreciprocal transduction can be obtained in the limit of large cooperativity in both directions, from optical to rf and vice versa. We also study the transducer noise and show that mechanical thermal noise is always reflected back onto the isolated port. In the limit of large cooperativity, the input noise is instead transmitted in an unaltered way in the allowed direction; in particular one has only vacuum noise in the output rf port in the case of optical-to-rf conversion.