Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1705.05608 · Superconductor Science and Technology

A self-aligned nano-fabrication process for vertical NbN–MgO–NbN Josephson junctions

A Grimm, S Jebari, Dibyendu Hazra, F Blanchet, F Gustavo, J-L Thomassin, M. Hofheinz

Published Jul 17, 2017• 7 citations
arXivHTMLPDF

Abstract

Abstract We present a new process for fabricating vertical NbN–MgO–NbN Josephson junctions using self-aligned silicon nitride spacers. It allows for a wide range of junction areas from 0.02 to several 100 μ m 2 . At the same time, it is suited for the implementation of complex microwave circuits with transmission line impedances ranging from < 1 Ω to > 1 k Ω . The constituent thin films and the finished junctions are characterized. The latter are shown to have high gap voltages ( > 4 mV ) and low sub-gap leakage currents.

DOI
10.1088/1361-6668/aa8007

Related papers

Fabrication of all-NbN Josephson tunnel junctions using single crystal NbN films for the base electrodes

Alexandre Shoji

All-NbN Josephson tunnel junctions with sputter-deposited magnesium oxide barriers have been fabricated using single-crystal NbN films for the base electrodes. Fabricated Josephson junctions have shown good tunneling characteristics with large gap voltages (5.6-5.8 mV), narrow gap widths (0.1-0.2 mV, from 30 to 70%), and small subgap leakage currents (V/sub m/=20-30 mV, measured at 3 mV). The results of a measurement of a subgap structure for a fabricated junction suggest that the excess leakage currents of fabricated junctions are due to multiparticle tunneling through locally thin areas in the MgO barriers.

IEEE Transactions on Magnetics•Mar 1, 1991•25 citations

Niobium nitride Josephson tunnel junctions with magnesium oxide barriers

Akira Shoji, Masahiro Aoyagi, S. Kosaka +2 more

Niobium nitride-niobium nitride Josephson tunnel junctions have been fabricated using amorphous magnesium oxide (a-MgO) films as barriers. These junctions have excellent tunneling characteristics. For example, a large gap voltage (Vg=5.1 mV), a large product of the maximum critical current and the normal tunneling resistance (IcRn=3.25 mV), and a small subgap leakage current (Vm=45 mV, measured at 3 mV) have been obtained for a NbN/a-MgO/NbN junction. The critical current of this junction remains finite up to 14.5 K.

Applied Physics Letters•Jun 1, 1985•137 citations

Development of NbN Josephson Junction technology

Masoud Radparvar

A novel process suitable for fabrication superconducting circuitry based on the all refactory material NbN is described. In this process, and in-situ trilayer film composed of NbN/MgO/NbN is used to fabricate Josephson tunnel junctions. Reactive ion etching processes are used to delineate devices and pattern insulators and metallizations. Fabricated junctions have yielded good tunneling characteristics with reasonable current density uniformity and reproducibility. Devices with gap voltages close to 3mV have been achieved for high quality junctions (Vm 20 mV). In addition to the trilayer, there are two wiring layers, two resistor depositions, and two insulation layers, constituting a full NbN based fabrication technology. Using this process, we fabricated and successfully tested thin film DC SQUID and time domain reflectometer (TDR) circuits. Preliminary measurements suggest that the critical temperature of these circuits is well within the operating temperature of commercial two-stage closed cycle refrigerators. (Author)

Final Report•Jul 24, 1986•0 citations

Sidewall spacer passivated epitaxial NbN/AlN/NbN Josephson junctions for superconducting qubit applications

Koki Honda, Daiki Kurihara, Hiroki Kutsuma +2 more

Epitaxial NbN/AlN/NbN Josephson junctions are promising alternatives to conventional Al/AlO$_x$/Al junctions for superconducting qubits due to their crystalline tunnel barriers and the high transition temperature of NbN. However, their integration into quantum circuits typically requires complex fabrication processes involving amorphous interlayer dielectrics, which can degrade qubit coherence times. To address these issues, we developed sidewall spacer passivated epitaxial NbN/AlN/NbN junctions using a fabrication process that reduces both the volume of amorphous dielectric material and fabrication complexity. The fabricated junctions exhibited a large gap voltage of approximately 5.6 mV and low subgap leakage currents. By varying the thickness of the AlN tunnel barrier, high-quality junctions were fabricated over a wide range of critical current densities ${\it J}_c$, from 0.3 to 10$^4$ A/cm$^2$. In addition, the comparison of the current-voltage characteristics before and after buffered hydrofluoric acid treatment indicated that the wet etching process did not degrade the electrical characteristics of the junctions. These results establish a scalable fabrication process for epitaxial Josephson junctions and provide a promising platform for high-coherence nitride-based superconducting qubits.

quant-pharXiv:2610.04820•Oct 6, 2026•0 citations

Fabrication and performance of all NbN Josephson junction circuits

Masoud Radparvar, M. Berry, R.E. Drake +3 more

A novel process suitable for fabricating superconducting circuitry based on the all refractory material NbN is described. In this process, an in-situ trilayer film composed of NbN/MgO/NbN is used to fabricate Josephson tunnel junctions. Reactive ion etching processes are used to delineate devices and pattern insulators and metallizations. Fabricated junctions have yielded good tunneling characteristics with reasonable current density uniformity and reproducibility. Devices with gap voltages close to 5mV have been achieved for high quality junctions. In addition to the trilayer, there are two wiring layers, two resistor depositions, and two insulation layers, constituting a full NbN based fabrication technology. Using this process, we fabricated and successfully tested thin film DC SQUID and time domain reflectometer (TDR) circuits. Preliminary measurements suggest that the critical temperature of these circuits is well within the operating temperature of commercial two-stage closed cycle refrigerators.

IEEE Transactions on Magnetics•Mar 1, 1987•32 citations

Low-loss epitaxial NbN/MgO/NbN trilayers for THz applications

Akira Kawakami, Zhen Wang, Shigehito Miki

To improve the performance of Josephson oscillators and SIS mixers over 700 GHz, we have developed a fabrication process to grow epitaxial NbN/MgO/NbN trilayers by reactive dc-sputtering. Trilayers were fabricated on a single-crystal MgO substrate at ambient temperature. NbN and MgO films were deposited by reactive dc-sputtering with an Nb and Mg target, respectively. The MgO inter-layer thickness was changed up to 480 nm, but, T/sub C/ and 20-K resistivity of the NbN upper-layer showed no remarkable dependency and they were 15.7 K and about 60 /spl mu//spl Omega/cm, respectively. To evaluate the RF performance of the epitaxial NbN films, we fabricated Josephson junctions with a microstrip resonator constructed from an epitaxial NbN/MgO/NbN trilayer. The I-V characteristics of the junction exhibited resonance steps up to 2.5 mV, which suggests that the epitaxial NbN films have low loss up to 1.2 THz.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•30 citations
Abstract We present a new process for fabricating vertical NbN–MgO–NbN Josephson junctions using self-aligned silicon nitride spacers. It allows for a wide range of junction areas from 0.02 to several 100 μ m 2 . At the same time, it is suited for the implementation of complex microwave circuits with transmission line impedances ranging from < 1 Ω to > 1 k Ω . The constituent thin films and the finished junctions are characterized. The latter are shown to have high gap voltages ( > 4 mV ) and low sub-gap leakage currents.
All-NbN Josephson tunnel junctions with sputter-deposited magnesium oxide barriers have been fabricated using single-crystal NbN films for the base electrodes. Fabricated Josephson junctions have shown good tunneling characteristics with large gap voltages (5.6-5.8 mV), narrow gap widths (0.1-0.2 mV, from 30 to 70%), and small subgap leakage currents (V/sub m/=20-30 mV, measured at 3 mV). The results of a measurement of a subgap structure for a fabricated junction suggest that the excess leakage currents of fabricated junctions are due to multiparticle tunneling through locally thin areas in the MgO barriers.
Niobium nitride-niobium nitride Josephson tunnel junctions have been fabricated using amorphous magnesium oxide (a-MgO) films as barriers. These junctions have excellent tunneling characteristics. For example, a large gap voltage (Vg=5.1 mV), a large product of the maximum critical current and the normal tunneling resistance (IcRn=3.25 mV), and a small subgap leakage current (Vm=45 mV, measured at 3 mV) have been obtained for a NbN/a-MgO/NbN junction. The critical current of this junction remains finite up to 14.5 K.
A novel process suitable for fabrication superconducting circuitry based on the all refactory material NbN is described. In this process, and in-situ trilayer film composed of NbN/MgO/NbN is used to fabricate Josephson tunnel junctions. Reactive ion etching processes are used to delineate devices and pattern insulators and metallizations. Fabricated junctions have yielded good tunneling characteristics with reasonable current density uniformity and reproducibility. Devices with gap voltages close to 3mV have been achieved for high quality junctions (Vm 20 mV). In addition to the trilayer, there are two wiring layers, two resistor depositions, and two insulation layers, constituting a full NbN based fabrication technology. Using this process, we fabricated and successfully tested thin film DC SQUID and time domain reflectometer (TDR) circuits. Preliminary measurements suggest that the critical temperature of these circuits is well within the operating temperature of commercial two-stage closed cycle refrigerators. (Author)
Epitaxial NbN/AlN/NbN Josephson junctions are promising alternatives to conventional Al/AlOx_xx​/Al junctions for superconducting qubits due to their crystalline tunnel barriers and the high transition temperature of NbN. However, their integration into quantum circuits typically requires complex fabrication processes involving amorphous interlayer dielectrics, which can degrade qubit coherence times. To address these issues, we developed sidewall spacer passivated epitaxial NbN/AlN/NbN junctions using a fabrication process that reduces both the volume of amorphous dielectric material and fabrication complexity. The fabricated junctions exhibited a large gap voltage of approximately 5.6 mV and low subgap leakage currents. By varying the thickness of the AlN tunnel barrier, high-quality junctions were fabricated over a wide range of critical current densities Jc{\it J}_cJc​, from 0.3 to 104^44 A/cm2^22. In addition, the comparison of the current-voltage characteristics before and after buffered hydrofluoric acid treatment indicated that the wet etching process did not degrade the electrical characteristics of the junctions. These results establish a scalable fabrication process for epitaxial Josephson junctions and provide a promising platform for high-coherence nitride-based superconducting qubits.
A novel process suitable for fabricating superconducting circuitry based on the all refractory material NbN is described. In this process, an in-situ trilayer film composed of NbN/MgO/NbN is used to fabricate Josephson tunnel junctions. Reactive ion etching processes are used to delineate devices and pattern insulators and metallizations. Fabricated junctions have yielded good tunneling characteristics with reasonable current density uniformity and reproducibility. Devices with gap voltages close to 5mV have been achieved for high quality junctions. In addition to the trilayer, there are two wiring layers, two resistor depositions, and two insulation layers, constituting a full NbN based fabrication technology. Using this process, we fabricated and successfully tested thin film DC SQUID and time domain reflectometer (TDR) circuits. Preliminary measurements suggest that the critical temperature of these circuits is well within the operating temperature of commercial two-stage closed cycle refrigerators.
To improve the performance of Josephson oscillators and SIS mixers over 700 GHz, we have developed a fabrication process to grow epitaxial NbN/MgO/NbN trilayers by reactive dc-sputtering. Trilayers were fabricated on a single-crystal MgO substrate at ambient temperature. NbN and MgO films were deposited by reactive dc-sputtering with an Nb and Mg target, respectively. The MgO inter-layer thickness was changed up to 480 nm, but, T/sub C/ and 20-K resistivity of the NbN upper-layer showed no remarkable dependency and they were 15.7 K and about 60 /spl mu//spl Omega/cm, respectively. To evaluate the RF performance of the epitaxial NbN films, we fabricated Josephson junctions with a microstrip resonator constructed from an epitaxial NbN/MgO/NbN trilayer. The I-V characteristics of the junction exhibited resonance steps up to 2.5 mV, which suggests that the epitaxial NbN films have low loss up to 1.2 THz.