Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1005.1110 · Applied Physics Letters

Approaching ideal weak link behavior with three dimensional aluminum nanobridges

R. Vijay, Eli M. Levenson-Falk, D. H. Slichter, I. Siddiqi

Published May 31, 2010• 76 citations
arXivHTMLPDF

Abstract

We investigate unshunted dc superconducting quantum interference devices (SQUIDs) consisting of aluminum nanobridges of varying length L contacted with (two dimensional, or 2D) and (three dimensional, or 3D) banks. 3D nanobridge SQUIDs with L≤150 nm (approximately four times the superconducting coherence length) exhibit ≈70% critical current modulation with applied magnetic field, approaching the theoretical limit for an ideal short metallic weak link. In contrast, 2D nanobridge SQUIDs exhibit significantly lower critical current modulation. This enhanced nonlinearity makes 3D nanobridge Josephson junctions well suited to optimize sensitivity in weak link SQUID magnetometers as well as realize ultralow-noise amplifiers and qubits.

DOI
10.1063/1.3443716

Related papers

Nonlinear microwave response of aluminum weak-link Josephson oscillators

Eli M. Levenson-Falk, R. Vijay, I. Siddiqi

We present the driven response at T=30 mK of 6 GHz superconducting resonators constructed from capacitively-shunted three-dimensional (3D) aluminum nanobridge superconducting quantum interference devices (nanoSQUIDs). We observe flux modulation of the resonant frequency in quantitative agreement with numerical calculation and characteristic of near-ideal short weak-link junctions. Under strong microwave excitation, we observe stable bifurcation in devices with coupled quality factor (Q) ranging from 30–3500. Near this bias point, parametric amplification with >20 dB gain, 40 MHz bandwidth, and near quantum-limited noise performance is observed. Our results indicate that 3D nanobridge junctions are attractive circuit elements to realize quantum bits.

arXiv:1101.4672•Applied Physics Letters•Mar 21, 2011•37 citations

Nanobridge superconducting quantum interference devices: Beyond the Josephson limit

Dibyendu Hazra

Nanoscale superconducting quantum interference devices (nano-SQUIDS) where the weak links are made from nanobridges, i.e., nanobridge SQUIDs (NBSs), are one of the most sensitive magnetometers for nanoscale magnetometry. Because of very strong nonlinearity in the nanobridge-electrode joints, the applied magnetic flux (${\mathrm{\ensuremath{\Phi}}}_{a}$)--critical current (${I}_{c}$) characteristics of NBSs differ very significantly from conventional tunnel-junction SQUIDs, especially when the nanobridges are long and/or the screening parameter is large. However, in most of the theoretical descriptions, NBSs have been treated as the conventional tunnel-junction SQUIDs, which are based on the dc Josephson effect. Here, I present a model demonstrating that for long nanobridges and/or large screening parameters the ${I}_{c}({\mathrm{\ensuremath{\Phi}}}_{a})$ of a NBS can be explained by merely considering the fluxoid quantization in the NBS loop and the energy of the NBS; it is not necessary to take the Josephson effect into consideration. I also demonstrate that using the model, one can derive useful expressions such as the modulation depth and transfer function. I discuss the role of the kinetic inductance fraction ($\ensuremath{\kappa}$) in determining ${I}_{c}({\mathrm{\ensuremath{\Phi}}}_{a})$. I compare the predictions of the present model with the experimental data already published by several groups.

arXiv:1809.09510•Physical review. B./Physical review. B•Apr 5, 2019•11 citations

Optimizing Anharmonicity in Nanoscale Weak Link Josephson Junction Oscillators

Rajamani Vijay, Jay Deep Sau, Marvin L. Cohen +1 more

We compute the current phase relation for superconducting weak links, with dimensions comparable to the zero temperature coherence length, connected to two and three dimensional superconducting electrodes. Our results indicate that 50-100 nm long aluminum nanobridges with three dimensional banks have sufficient anharmonicity for realizing low noise amplifiers and quantum bits. Such weak link junctions thus present a practical new route for realizing sensitive quantum circuits with potentially higher quality factor than tunnel junction devices due to the absence of a lossy oxide layer.

arXiv:0905.2217•Physical Review Letters•Aug 19, 2009•49 citations

Niobium Quantum Interference Microwave Circuits with Monolithic Three-Dimensional (3D) Nanobridge Junctions

Kevin Uhl, Daniel Hackenbeck, Janis Peter +3 more

Nonlinear microwave circuits are key elements for many groundbreaking research directions and technologies, such as quantum computation and quantum sensing. The majority of microwave circuits with Josephson nonlinearities to date is based on aluminum thin films, and therefore they are severely restricted in their operation range regarding temperatures and external magnetic fields. Here, we present the realization of superconducting niobium microwave resonators with integrated, three-dimensional (3D) nanobridge-based superconducting quantum interference devices. The 3D nanobridges (constriction weak links) are monolithically patterned into pre-fabricated microwave LC circuits using neon ion beam milling, and the resulting quantum interference circuits show frequency tunabilities, flux responsivities and Kerr nonlinearities on par with comparable aluminum nanobridge devices, but with the perspective of a much larger operation parameter regime. Our results reveal great potential for application of these circuits in hybrid systems with e.g. magnons and spin ensembles or in flux-mediated optomechanics.

arXiv:2305.16276•May 25, 2023•0 citations

Fabrication and Characterization of Miniaturized NbN Superconducting Quantum Interference Devices With Nanobridge Junctions

Hao Wang, Lei Chen, Xiaoyu Liu +4 more

Reduction of the size of the superconducting quantum interference device (SQUID) ring structure improves its sensitivity to magnetic moments. Nanobridge junctions are advantageous for SQUID miniaturization. However, many planar SQUIDs with nanobridge junctions have shallow flux modulation depths because of their nonideal Josephson current-phase relationships. Here, we fabricated a three-dimensional niobium nitride (NbN) miniaturized SQUID in which the nanobridge junction structures are much thinner than the superconducting ring. We grew a thick superconducting NbN film on a silicon wafer and embedded an insulating slit in the middle of the film. By setting two thin nanobridge junctions across this insulating slit, we were able to manufacture NbN miniaturized SQUIDs that, in principle, can become nano-SQUIDs. The flux modulation depths of these devices reached 36% at 4.2 K. In addition, the fabricated devices show reversible current-voltage characteristics in the absence of any shunting resistance.

IEEE Transactions on Applied Superconductivity•Jan 18, 2017•10 citations

Static and Microwave Transport Properties of Aluminum Nanobridge Josephson Junctions

Eli M. Levenson-Falk

Josephson junctions are the basis of superconducting qubits, amplifiers, and magnetometers. Historically, tunnel-style junctions have been most common. However, for some applications--those requiring a small, highly transparent, all-superconducting junction--nanobridge weak link junctions may be preferable. This thesis presents extensive characterization of aluminum nanobridge Josephson junctions. The junction behavior is simulated by numerically solving the Usadel equations. These simulations are then tested and confirmed via low- and microwave-frequency transport measurements. The data confirm that nanobridge junctions approach the ideal weak-link Josephson limit.Such a near-ideal junction can be used in a superconducting quantum interference device (SQUID) to form an ultra sensitive magnetometer. This thesis presents the first nanobridge-based dispersive SQUID magnetometer. The devices show near-zero dissipation, with bandwidth and sensitivity on par with the best reported results for any SQUID-based magnetometer. These magnetometers have several flexible modes of operation, allowing for optimization of sensitivity, bandwidth, or backaction. They also provide insight into the internal dynamics of dispersive measurement with nonlinear cavities, as the magnetometer backaction depends on the bias point and can readily be measured.Nanobridge junctions also provide a useful tool for diagnosing sources of decoherence in superconducting qubits. By replacing the usual tunnel junction with a nanobridge, the contribution of the junction to decoherence processes may be probed. In particular, the interaction of nanobridge junctions with quasiparticles provides information both about the junctions themselves and about quasiparticle generation and relaxation mechanisms. This thesis reports measurements of nonequilibrium quasiparticles trapping in phase-biased nanobridge junctions. By probing the quasiparticle-induced changes in resonant frequency of a high-Q nanoSQUID oscillator, one may measure the mean distribution of trapped quasiparticles and study its temperature dependence. These measurements also provide spectroscopy of the junctions' internal Andreev states and the dynamics of quasiparticle excitation and retrapping. The work presented here demonstrates the utility of nanobridge junctions as a tool for quantifying the population and distribution of quasiparticles in a superconducting circuit.

•Jan 1, 2013•0 citations
We investigate unshunted dc superconducting quantum interference devices (SQUIDs) consisting of aluminum nanobridges of varying length L contacted with (two dimensional, or 2D) and (three dimensional, or 3D) banks. 3D nanobridge SQUIDs with L≤150 nm (approximately four times the superconducting coherence length) exhibit ≈70% critical current modulation with applied magnetic field, approaching the theoretical limit for an ideal short metallic weak link. In contrast, 2D nanobridge SQUIDs exhibit significantly lower critical current modulation. This enhanced nonlinearity makes 3D nanobridge Josephson junctions well suited to optimize sensitivity in weak link SQUID magnetometers as well as realize ultralow-noise amplifiers and qubits.
We present the driven response at T=30 mK of 6 GHz superconducting resonators constructed from capacitively-shunted three-dimensional (3D) aluminum nanobridge superconducting quantum interference devices (nanoSQUIDs). We observe flux modulation of the resonant frequency in quantitative agreement with numerical calculation and characteristic of near-ideal short weak-link junctions. Under strong microwave excitation, we observe stable bifurcation in devices with coupled quality factor (Q) ranging from 30–3500. Near this bias point, parametric amplification with >20 dB gain, 40 MHz bandwidth, and near quantum-limited noise performance is observed. Our results indicate that 3D nanobridge junctions are attractive circuit elements to realize quantum bits.
Nanoscale superconducting quantum interference devices (nano-SQUIDS) where the weak links are made from nanobridges, i.e., nanobridge SQUIDs (NBSs), are one of the most sensitive magnetometers for nanoscale magnetometry. Because of very strong nonlinearity in the nanobridge-electrode joints, the applied magnetic flux (${\mathrm{\ensuremath{\Phi}}}_{a}$)--critical current (Ic{I}_{c}Ic​) characteristics of NBSs differ very significantly from conventional tunnel-junction SQUIDs, especially when the nanobridges are long and/or the screening parameter is large. However, in most of the theoretical descriptions, NBSs have been treated as the conventional tunnel-junction SQUIDs, which are based on the dc Josephson effect. Here, I present a model demonstrating that for long nanobridges and/or large screening parameters the ${I}_{c}({\mathrm{\ensuremath{\Phi}}}_{a})$ of a NBS can be explained by merely considering the fluxoid quantization in the NBS loop and the energy of the NBS; it is not necessary to take the Josephson effect into consideration. I also demonstrate that using the model, one can derive useful expressions such as the modulation depth and transfer function. I discuss the role of the kinetic inductance fraction ($\ensuremath{\kappa}$) in determining ${I}_{c}({\mathrm{\ensuremath{\Phi}}}_{a})$. I compare the predictions of the present model with the experimental data already published by several groups.
We compute the current phase relation for superconducting weak links, with dimensions comparable to the zero temperature coherence length, connected to two and three dimensional superconducting electrodes. Our results indicate that 50-100 nm long aluminum nanobridges with three dimensional banks have sufficient anharmonicity for realizing low noise amplifiers and quantum bits. Such weak link junctions thus present a practical new route for realizing sensitive quantum circuits with potentially higher quality factor than tunnel junction devices due to the absence of a lossy oxide layer.
Nonlinear microwave circuits are key elements for many groundbreaking research directions and technologies, such as quantum computation and quantum sensing. The majority of microwave circuits with Josephson nonlinearities to date is based on aluminum thin films, and therefore they are severely restricted in their operation range regarding temperatures and external magnetic fields. Here, we present the realization of superconducting niobium microwave resonators with integrated, three-dimensional (3D) nanobridge-based superconducting quantum interference devices. The 3D nanobridges (constriction weak links) are monolithically patterned into pre-fabricated microwave LC circuits using neon ion beam milling, and the resulting quantum interference circuits show frequency tunabilities, flux responsivities and Kerr nonlinearities on par with comparable aluminum nanobridge devices, but with the perspective of a much larger operation parameter regime. Our results reveal great potential for application of these circuits in hybrid systems with e.g. magnons and spin ensembles or in flux-mediated optomechanics.
Reduction of the size of the superconducting quantum interference device (SQUID) ring structure improves its sensitivity to magnetic moments. Nanobridge junctions are advantageous for SQUID miniaturization. However, many planar SQUIDs with nanobridge junctions have shallow flux modulation depths because of their nonideal Josephson current-phase relationships. Here, we fabricated a three-dimensional niobium nitride (NbN) miniaturized SQUID in which the nanobridge junction structures are much thinner than the superconducting ring. We grew a thick superconducting NbN film on a silicon wafer and embedded an insulating slit in the middle of the film. By setting two thin nanobridge junctions across this insulating slit, we were able to manufacture NbN miniaturized SQUIDs that, in principle, can become nano-SQUIDs. The flux modulation depths of these devices reached 36% at 4.2 K. In addition, the fabricated devices show reversible current-voltage characteristics in the absence of any shunting resistance.
Josephson junctions are the basis of superconducting qubits, amplifiers, and magnetometers. Historically, tunnel-style junctions have been most common. However, for some applications--those requiring a small, highly transparent, all-superconducting junction--nanobridge weak link junctions may be preferable. This thesis presents extensive characterization of aluminum nanobridge Josephson junctions. The junction behavior is simulated by numerically solving the Usadel equations. These simulations are then tested and confirmed via low- and microwave-frequency transport measurements. The data confirm that nanobridge junctions approach the ideal weak-link Josephson limit.Such a near-ideal junction can be used in a superconducting quantum interference device (SQUID) to form an ultra sensitive magnetometer. This thesis presents the first nanobridge-based dispersive SQUID magnetometer. The devices show near-zero dissipation, with bandwidth and sensitivity on par with the best reported results for any SQUID-based magnetometer. These magnetometers have several flexible modes of operation, allowing for optimization of sensitivity, bandwidth, or backaction. They also provide insight into the internal dynamics of dispersive measurement with nonlinear cavities, as the magnetometer backaction depends on the bias point and can readily be measured.Nanobridge junctions also provide a useful tool for diagnosing sources of decoherence in superconducting qubits. By replacing the usual tunnel junction with a nanobridge, the contribution of the junction to decoherence processes may be probed. In particular, the interaction of nanobridge junctions with quasiparticles provides information both about the junctions themselves and about quasiparticle generation and relaxation mechanisms. This thesis reports measurements of nonequilibrium quasiparticles trapping in phase-biased nanobridge junctions. By probing the quasiparticle-induced changes in resonant frequency of a high-Q nanoSQUID oscillator, one may measure the mean distribution of trapped quasiparticles and study its temperature dependence. These measurements also provide spectroscopy of the junctions' internal Andreev states and the dynamics of quasiparticle excitation and retrapping. The work presented here demonstrates the utility of nanobridge junctions as a tool for quantifying the population and distribution of quasiparticles in a superconducting circuit.