Noise performance is one of the most crucial aspects of any detector. Superconducting Microwave Kinetic Inductance Detectors (MKIDs) have an “excess” frequency noise that shows up as a small time dependent jitter of the resonance frequency characterized by the frequency noise power spectrum measured in units of Hz2/Hz. Recent studies have shown that this noise almost certainly originates from a surface layer of two‐level system (TLS) defects on the metallization or substrate. Fluctuation of these TLSs introduces noise in the resonator due to coupling of the TLS electric dipole moments to the resonator’s electric field. Motivated by a semi‐empirical quantitative theory of this noise mechanism, we have designed and tested new resonator geometries in which the high‐field “capacitive” portion of the CPW resonator is replaced by an interdigitated capacitor (IDC) structure with 10–20 μm electrode spacing, as compared to the 2 μm spacing used for our more conventional CPW resonators. Measurements show that this new IDC design has dramatically lower TLS noise, currently by about a factor of ∼29 in terms of the frequency noise power spectrum, corresponding to an improvement of about a factor of 29 in NEP. These new devices are replacing the CPW resonators in our next design iteration in progress for MKIDCam. Opportunities and prospects for future reduction of the TLS noise will be discussed.
Noise performance is one of the most crucial aspects of any detector. Superconducting Microwave Kinetic Inductance Detectors (MKIDs) have an “excess” frequency noise that shows up as a small time dependent jitter of the resonance frequency characterized by the frequency noise power spectrum measured in units of Hz2/Hz. Recent studies have shown that this noise almost certainly originates from a surface layer of two‐level system (TLS) defects on the metallization or substrate. Fluctuation of these TLSs introduces noise in the resonator due to coupling of the TLS electric dipole moments to the resonator’s electric field. Motivated by a semi‐empirical quantitative theory of this noise mechanism, we have designed and tested new resonator geometries in which the high‐field “capacitive” portion of the CPW resonator is replaced by an interdigitated capacitor (IDC) structure with 10–20 μm electrode spacing, as compared to the 2 μm spacing used for our more conventional CPW resonators. Measurements show that this new IDC design has dramatically lower TLS noise, currently by about a factor of ∼29 in terms of the frequency noise power spectrum, corresponding to an improvement of about a factor of 29 in NEP. These new devices are replacing the CPW resonators in our next design iteration in progress for MKIDCam. Opportunities and prospects for future reduction of the TLS noise will be discussed.
The separation and optimization of noise components is critical to microwave-kinetic inductance detector (MKID) development. We analyze the effect of several changes to the lumped-element inductor and interdigitated capacitor geometry on the noise performance of a series of MKIDs intended for millimeter-wavelength experiments. We extract the contributions from two-level system noise in the dielectric layer, the generation-recombination noise intrinsic to the superconducting thin-film, and system white noise from each detector noise power spectrum and characterize how these noise components depend on detector geometry, material, and measurement conditions such as driving power and temperature. We observe a reduction in the amplitude of two-level system noise with both an elevated sample temperature and an increased gap between the fingers within the interdigitated capacitors for both aluminum and niobium detectors. We also verify the expected reduction of the generation-recombination noise and associated quasiparticle lifetime with reduced inductor volume. This study also iterates over different materials, including aluminum, niobium, and aluminum manganese, and compares the results with an underlying physical model.
Microwave Kinetic Inductance Detectors (MKIDs) are extremely sensitive radiation detectors based on superconducting resonators that can be combined in large arrays on a single readout line within a limited frequency bandwidth. This makes MKIDs ideal detectors for the ultimate far-infrared observatory: a future space-based actively cooled telescope with its performance solely limited by the low universe background radiation. However, to reach these detector requirements, state-of-the-art MKIDs still need a order of magnitude improvement in device sensitivity. In this work, the MKID sensitivity is improved by reducing the aluminium volume that absorbs pair-breaking radiation into quasiparticle excitations, while making sure all radiation is still absorbed. Furthermore, a key requirement is sufficient reduction of excess noise as to keep the device intrinsically limited by thermally driven random fluctuations in the number of quasiparticles in absence of radiation, or Generation-Recombination (G-R) noise. To this end, a model is developed that describes the noise contributions as function of device geometry, readout power, material properties and radiation power. Subsequently, a realistic MKID design is presented and tested that reduces excess noise and maximises the sensitivity, expressed as Noise Equivalent Power (NEP). At high temperatures, good overall agreement is found between the measured noise spectra and the model. At low temperature T = 120 mK, the measurement results give an optical NEP similar to current state-of-the-art MKIDs. The NEP is not as low as expected due to short quasiparticle lifetimes, an unexpected decrease in the G-R noise level and a very high excess noise attributed to Two-Level Systems (TLS) noise that starts to dominate the already low G-R noise spectrum at low temperatures. Possibly, the quick quasiparticle lifetime saturation and noise level drop are caused by a strong readout power effect, as the readout power is known to create excess quasiparticles and to cause a strongly non-thermal electron energy distribution in the aluminium strip of the MKID. However, the exact microscopic details of these effects are unknown and not studied in this project. Based on the current chip design, a straightforward way to improve device performance and study the readout power effect in more detail is a reduction of the high TLS noise levels, which is possibly fabrication related. This would allow an unobstructed view of the G-R noise spectrum at low temperatures, thereby allowing both a study of the readout power effect on the quasiparticle system, and ultimately achieving the improvement in NEP needed reach the detector requirements for the ultimate space-based far-infrared observatory.
Over the past two decades, microwave kinetic inductance detectors (MKIDs) have gained exceptional importance in millimeter and sub-millimeter astronomy. MKIDs consist of thin strip resonators capable of detecting changes in the surface impedance of superconductor strips, which result from variations in resonance circuit properties. The principal noise in MKIDs comprises excess frequency noise and two-level system noise. In this paper, we propose a technique to mitigate the effect of two-level system (TLS) noise in MKIDs using a parallel plate capacitor with three layers of high ε dielectrics. To achieve this, we employ three layers of Al2O3, HfO2, and TiO2 with equal thickness between the capacitor plates. The experimental results demonstrate a nearly 30% reduction in TLS power spectral density.
Abstract A microwave kinetic inductance detector (MKID) is a cutting-edge superconducting detector. It comprises a resonator circuit constructed with a superconducting film on a dielectric substrate. To expand its field of application, it is important to establish a method to suppress the two-level system (TLS) noise that is caused by the electric fluctuations between the two energy states at the surface of the substrate. The electric field density can be decreased by expanding the strip width (S) and gap width from the ground plane (W) in the MKID circuit, allowing the suppression of TLS noise. However, this effect has not yet been confirmed for MKIDs made with niobium films on silicon substrates. In this study, we demonstrate its effectiveness for such MKIDs. We expanded the dimension of the circuit from (S, W) = (3.00 μm, 4.00 μm) to (S, W) = (5.00 μm, 23.7 μm), and achieved an increased suppression of 5.5 dB in TLS noise.
Context. Microwave kinetic inductance detectors (MKIDs) are superconducting detectors that have the potential to contribute to the construction of over 10 000 pixel cameras required for mm and submm astronomical observations over the next decade. One of the issues related to its application is two-level-system (TLS) noise that creates a 1/ f term in the power spectrum density (PSD) of the detectors. A hybrid-type MKID has been proposed for TLS noise suppression without affecting the MKID performance. In this paper, we present a systematic method to model a hybrid-type MKID for mitigating TLS noise while achieving high sensitivity. Aims. Previous studies have shown that TLS noise in MKIDs depends on the sampling frequency, internal power, device geometry, and temperature. The strength of the electrical field distribution along the resonator line also affects the TLS noise properties. Based on this knowledge, we constructed a noise model of a hybrid-type MKID. Methods. Using this model, we designed MKIDs for the cosmic microwave background radiation experiment, GroundBIRD. We evaluated the 1/ f noise properties and NET of the fabricated devices using the on-site measurements. Based on the NET measurements, we can confirm that the white noise of fabricated detectors is limited by atmospheric photon noise. From the 1/ f noise measurements, we also confirm that it is possible to reach an atmospheric photon noise limit down to a low sampling frequency (i.e., of a few Hz) at the typical observation conditions from Teide observatory. Results. We confirm the design methodology we propose for hybrid-type MKID works well in optimizing the TLS model to the hybrid-type MKID, as evidenced by performance verification measurements carried out in the laboratory and on site.
Astronomical Kinetic Inductance Detectors (KIDs), similar to quantum information devices, experience performance limiting noise from materials. In particular, 1/f (frequency) noise can be a dominant noise mechanism, which arises from Two-Level System defects (TLSs) in the circuit dielectrics and material interfaces. Here we present a Dual-Resonator KID (DuRKID), which is designed for improved signal to noise (or noise equivalent power) relative to 1/f-noise limited KIDs. We first show the DuRKID schematic, fabricated circuit, and we follow with a description of the intended operation, first measurements, theory, and discussion. The circuit consists of two superconducting resonators sharing an electrical capacitance bridge of 4 capacitors, each of which hosts TLSs. The device is intended to operate using hybridization of the modes, which causes TLSs to either couple to one mode or the other, depending upon which capacitor they reside in. In contrast, the intended KID signal is directed to an inductor, and due to hybridization this causes correlated frequency changes in both (hybridized) modes. Therefore, one can distinguish photon signal from TLS frequency noise. To achieve hybridization, a TiN inductor is current biased to allow tuning of one bare resonator mode into degeneracy with the other and measurements show that the intended resonator modes frequency tune and hybridize as expected. The interresonator coupling and unintentional coupling of the 2 resonators to transmission lines are also characterized in measurements. In the theory, based on a quantum-information-science modes, we calculate the 4-port S parameters and simulate the 1/f frequency noise of the device. The study reveals that the DuRKID can exhibit a large and fundamental performance advantage over 1/f-noise-limited KID detectors.