Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0903.1243 · IEEE Transactions on Applied Superconductivity

Bandwidth and Dynamic Range of a Widely Tunable Josephson Parametric Amplifier

Manuel A. Castellanos-Beltran, K. D. Irwin, Leila R. Vale, Gene C Hilton, Konrad W. Lehnert

Published Jun 1, 2009• 31 citations
arXivHTMLPDF

Abstract

We characterize the signal bandwidth and dynamic range of a recently developed type of Josephson parametric amplifier. These amplifiers consist of a series array of SQUIDs embedded in a microwave cavity. They are narrow band, only amplifying signals close to the cavity's resonance frequency, but the cavity's resonance frequency, and hence the amplified band, can be widely tuned. For a particular realization of these amplifiers we measure how the signal bandwidth depends on amplifier's gain. We find that the amplitude gain times signal bandwidth is approximately the linewidth of the cavity. In addition we measure the amplifier's dynamic range and saturation power.

DOI
10.1109/tasc.2009.2018119

Related papers

Josephson Array-Mode Parametric Amplifier

Volodymyr Sivak, Shyam Shankar, Guangtong Liu +2 more

We introduce a near-quantum-limited amplifier with a large tunable bandwidth and high dynamic range---the Josephson array-mode parametric amplifier (JAMPA). The signal and idler modes involved in the amplification process are realized by the array modes of a chain of 1000 flux-tunable Josephson-junction-based nonlinear elements. The frequency spacing between the array modes is comparable to the flux tunability of the modes, ensuring that any desired frequency can be occupied by a resonant mode, which can further be pumped to produce high gain. We experimentally demonstrate that the device can be operated as a nearly quantum-limited parametric amplifier with 20 dB of gain at almost any frequency within a 4--12-GHz band. On average, it has a 3-dB bandwidth of 11 MHz and an input 1-dB compression power of $\ensuremath{-}108\phantom{\rule{0.2em}{0ex}}\mathrm{dBm}$, which can go as high as $\ensuremath{-}93\phantom{\rule{0.2em}{0ex}}\mathrm{dBm}$. We envision the application of such a device to the time- and frequency-multiplexed readout of multiple qubits, as well as to the generation of continuous-variable cluster states.

arXiv:1909.08005•Physical Review Applied•Feb 7, 2020•63 citations

Arrays of Josephson tunnel junctions as parametric amplifiers

S. Wahlsten, S. Rudner, T. Claeson

Arrays of 10 or 40 series-connected small densely packed Josephson tunnel junctions were successfully operated as parametric amplifiers at 10 GHz. Between 50 and 90% of the junctions in an array were observed to work coherently in the amplification process. Signal gain exceeding 24 dB was achieved with a pump power as low as −50 to −70 dBm. A power width (i.e., the range of the pump power for a gain within 3 dB of the peak gain) of 0.25 dB and a bandwidth of 15 MHz were measured for 20-dB gain. The power width was in accordance with theory but the bandwidth was reduced, probably due to noise saturation effects. The latter effects can be reduced by lowering the input noise temperature or by including an external band limitation. The noise temperature was also increased by saturation; however, with an external bandwidth of 60 MHz, a noise temperature of 30±20 K was measured. The application of a magnetic field has proved extremely useful as a means of tuning the amplifiers to stable high-gain operating points. This tuning was also utilized in evaluating the amplifier parameters, and the theory by Feldman, Parrish, and Chiao has been verified. The upper frequency limit for a lead tunnel junction amplifier ought to be well above 300 GHz.

Journal of Applied Physics•Jul 1, 1978•61 citations

Widely tunable parametric amplifier based on a superconducting quantum interference device array resonator

M. A. Castellanos-Beltran, Konrad W. Lehnert

The authors create a Josephson parametric amplifier from a transmission line resonator whose inner conductor is made from a series of superconducting quantum interference device (SQUID) array. By changing the magnetic flux through the SQUID loops, they are able to adjust the circuit’s resonance frequency and the center of the amplified band between 4 and 7.8GHz. They observe that the amplifier has gains as large as 28dB and infers that it adds less than twice the input vacuum noise.

arXiv:0706.2373•Applied Physics Letters•Aug 20, 2007•403 citations

High-gain weakly nonlinear flux-modulated Josephson parametric amplifier using a SQUID array

Xin Zhou, Vivien Schmitt, Patrice Bertet +4 more

We have developed and measured a high-gain quantum-limited microwave parametric amplifier based on a superconducting lumped LC resonator with the inductor L including an array of eight superconducting quantum interference devices (SQUIDs). This amplifier is parametrically pumped by modulating the flux threading the SQUIDs at twice the resonator frequency. Around 5 GHz, a maximum gain of 31 dB, a product amplitude gain $\ifmmode\times\else\texttimes\fi{}$ bandwidth above 60 MHz, and a 1 dB compression point of $\ensuremath{-}123$ dBm at 20 dB gain are obtained in the nondegenerate mode of operation. Phase-sensitive amplification-deamplification is also measured in the degenerate mode and yields a maximum gain of 37 dB. The compression point obtained is 18 dB above what would be obtained with a single SQUID of the same inductance, due to the smaller nonlinearity of the SQUID array.

arXiv:1409.5630•Physical Review B•Jun 30, 2014•101 citations

Parametric Microwave Amplification using a Tunable Superconducting Resonator

C. W. Sandbo Chang

In this Master thesis, I present a theoretical description and experimental measurements of a tunable microwave resonator operated as a parametric amplifier. Superconducting parametric amplifiers have attracted great interest in recent years as it has been demonstrated that they can operate with a noise performance at the standard quantum limit. \nParametric amplification is achieved in the devices by modulating the electrical length of the resonator at twice the resonance frequency. The device measured in this thesis consists of a quarter-wavelength microwave resonator fabricated in a thin-film aluminum coplanar waveguide geometry. With a termination to ground through a Superconducting Quantum Interference Device (SQUID), the boundary condition of the resonator becomes sensitive to an applied magnetic field. This enables the tuning of the resonance frequencies, using a DC magnetic field, over a wide frequency range of 670MHz. Similarly, an AC magnetic field then allows for the modulation of the resonator electrical length at microwave frequencies. \nWe characterized the device by first measuring the DC tuning curves of the 2nd and 3rd harmonics of the resonator, around 4 GHz and 6 GHz respectively. We then studied parametric amplification in the device when the electrical length was modulated at approximately twice the resonance frequency of one of the modes. We scanned the pump frequency and pump power over a wide range to study the region in parameters which gives parametric gain. We performed an in-depth parameter sweep over this region, identifying pump parameters that provided maximum gain and maximum system noise improvements compared the following HEMT amplifier. \nWe find that the use of the parametric amplifier can improve the system noise temperature by more than 10 dB compared to a start-of-the-art commercial HEMT amplifier. This implies a performance near the standard quantum limit.

•Sep 2, 2015•0 citations

Controlling the dynamic range of a Josephson parametric amplifier

Christopher Eichler, Andreas J. Wallraff

One of the central challenges in the development of parametric amplifiers is the control of the dynamic range relative to its gain and bandwidth, which typically limits quantum limited amplification to signals which contain only a few photons per inverse bandwidth. Here, we discuss the control of the dynamic range of Josephson parametric amplifiers by using Josephson junction arrays. We discuss gain, bandwidth, noise, and dynamic range properties of both a transmission line and a lumped element based parametric amplifier. Based on these investigations we derive useful design criteria, which may find broad application in the development of practical parametric amplifiers.

arXiv:1305.6583•EPJ Quantum Technology•Jan 29, 2014•154 citations
We characterize the signal bandwidth and dynamic range of a recently developed type of Josephson parametric amplifier. These amplifiers consist of a series array of SQUIDs embedded in a microwave cavity. They are narrow band, only amplifying signals close to the cavity's resonance frequency, but the cavity's resonance frequency, and hence the amplified band, can be widely tuned. For a particular realization of these amplifiers we measure how the signal bandwidth depends on amplifier's gain. We find that the amplitude gain times signal bandwidth is approximately the linewidth of the cavity. In addition we measure the amplifier's dynamic range and saturation power.
We introduce a near-quantum-limited amplifier with a large tunable bandwidth and high dynamic range---the Josephson array-mode parametric amplifier (JAMPA). The signal and idler modes involved in the amplification process are realized by the array modes of a chain of 1000 flux-tunable Josephson-junction-based nonlinear elements. The frequency spacing between the array modes is comparable to the flux tunability of the modes, ensuring that any desired frequency can be occupied by a resonant mode, which can further be pumped to produce high gain. We experimentally demonstrate that the device can be operated as a nearly quantum-limited parametric amplifier with 20 dB of gain at almost any frequency within a 4--12-GHz band. On average, it has a 3-dB bandwidth of 11 MHz and an input 1-dB compression power of $\ensuremath{-}108\phantom{\rule{0.2em}{0ex}}\mathrm{dBm}$, which can go as high as $\ensuremath{-}93\phantom{\rule{0.2em}{0ex}}\mathrm{dBm}$. We envision the application of such a device to the time- and frequency-multiplexed readout of multiple qubits, as well as to the generation of continuous-variable cluster states.
Arrays of 10 or 40 series-connected small densely packed Josephson tunnel junctions were successfully operated as parametric amplifiers at 10 GHz. Between 50 and 90% of the junctions in an array were observed to work coherently in the amplification process. Signal gain exceeding 24 dB was achieved with a pump power as low as −50 to −70 dBm. A power width (i.e., the range of the pump power for a gain within 3 dB of the peak gain) of 0.25 dB and a bandwidth of 15 MHz were measured for 20-dB gain. The power width was in accordance with theory but the bandwidth was reduced, probably due to noise saturation effects. The latter effects can be reduced by lowering the input noise temperature or by including an external band limitation. The noise temperature was also increased by saturation; however, with an external bandwidth of 60 MHz, a noise temperature of 30±20 K was measured. The application of a magnetic field has proved extremely useful as a means of tuning the amplifiers to stable high-gain operating points. This tuning was also utilized in evaluating the amplifier parameters, and the theory by Feldman, Parrish, and Chiao has been verified. The upper frequency limit for a lead tunnel junction amplifier ought to be well above 300 GHz.
We have developed and measured a high-gain quantum-limited microwave parametric amplifier based on a superconducting lumped LC resonator with the inductor L including an array of eight superconducting quantum interference devices (SQUIDs). This amplifier is parametrically pumped by modulating the flux threading the SQUIDs at twice the resonator frequency. Around 5 GHz, a maximum gain of 31 dB, a product amplitude gain $\ifmmode\times\else\texttimes\fi{}$ bandwidth above 60 MHz, and a 1 dB compression point of $\ensuremath{-}123$ dBm at 20 dB gain are obtained in the nondegenerate mode of operation. Phase-sensitive amplification-deamplification is also measured in the degenerate mode and yields a maximum gain of 37 dB. The compression point obtained is 18 dB above what would be obtained with a single SQUID of the same inductance, due to the smaller nonlinearity of the SQUID array.
In this Master thesis, I present a theoretical description and experimental measurements of a tunable microwave resonator operated as a parametric amplifier. Superconducting parametric amplifiers have attracted great interest in recent years as it has been demonstrated that they can operate with a noise performance at the standard quantum limit. \nParametric amplification is achieved in the devices by modulating the electrical length of the resonator at twice the resonance frequency. The device measured in this thesis consists of a quarter-wavelength microwave resonator fabricated in a thin-film aluminum coplanar waveguide geometry. With a termination to ground through a Superconducting Quantum Interference Device (SQUID), the boundary condition of the resonator becomes sensitive to an applied magnetic field. This enables the tuning of the resonance frequencies, using a DC magnetic field, over a wide frequency range of 670MHz. Similarly, an AC magnetic field then allows for the modulation of the resonator electrical length at microwave frequencies. \nWe characterized the device by first measuring the DC tuning curves of the 2nd and 3rd harmonics of the resonator, around 4 GHz and 6 GHz respectively. We then studied parametric amplification in the device when the electrical length was modulated at approximately twice the resonance frequency of one of the modes. We scanned the pump frequency and pump power over a wide range to study the region in parameters which gives parametric gain. We performed an in-depth parameter sweep over this region, identifying pump parameters that provided maximum gain and maximum system noise improvements compared the following HEMT amplifier. \nWe find that the use of the parametric amplifier can improve the system noise temperature by more than 10 dB compared to a start-of-the-art commercial HEMT amplifier. This implies a performance near the standard quantum limit.
One of the central challenges in the development of parametric amplifiers is the control of the dynamic range relative to its gain and bandwidth, which typically limits quantum limited amplification to signals which contain only a few photons per inverse bandwidth. Here, we discuss the control of the dynamic range of Josephson parametric amplifiers by using Josephson junction arrays. We discuss gain, bandwidth, noise, and dynamic range properties of both a transmission line and a lumped element based parametric amplifier. Based on these investigations we derive useful design criteria, which may find broad application in the development of practical parametric amplifiers.