We optimize fault-tolerant quantum error correction to reduce the number of syndrome bit measurements. Speeding up error correction will also speed up an encoded quantum computation, and should reduce its effective error rate. We give both code-specific and general methods, using a variety of techniques and in a variety of settings. We design new quantum error-correcting codes specifically for efficient error correction, e.g., allowing single-shot error correction. For codes with multiple logical qubits, we give methods for combining error correction with partial logical measurements. There are tradeoffs in choosing a code and error-correction technique. While to date most work has concentrated on optimizing the syndrome-extraction procedure, we show that there are also substantial benefits to optimizing how the measured syndromes are chosen and used. As an example, we design single-shot measurement sequences for fault-tolerant quantum error correction with the 16-qubit extended Hamming code. Our scheme uses 10 syndrome bit measurements, compared to 40 measurements with the Shor scheme. We design single-shot logical measurements as well: any logical Z measurement can be made together with fault-tolerant error correction using only 11 measurements. For comparison, using the Shor scheme a basic implementation of such a non-destructive logical measurement uses 63 measurements. We also offer ten open problems, the solutions of which could lead to substantial improvements of fault-tolerant error correction.
Quantum computers have the potential to solve several interesting problems in polynomial \ntime for which no polynomial time classical algorithms have been found. However, \none of the major challenges in building quantum devices is that quantum systems are very \nsensitive to noise arising from undesired interactions with the environment. Noise can lead \nto errors which can corrupt the results of the computation. Quantum error correction is \none way to mitigate the effects of noise arising in quantum devices. \nWith a plethora of quantum error correcting codes that can be used in various settings, \none of the main challenges of quantum error correction is understanding how well various \ncodes perform under more realistic noise models that can be observed in experiments. \nThis thesis proposes a new decoding algorithm which can optimize threshold values of \nerror correcting codes under different noise models. The algorithm can be applied to \nany Markovian noise model. Further, it is shown that for certain noise models, logical \nClifford corrections can further improve a code's threshold value if the code obeys certain \nsymmetries. \n \nSince gates and measurements cannot in general be performed with perfect precision, \nthe operations required to perform quantum error correction can introduce more errors \ninto the system thus negating the benefits of error correction. Fault-tolerant quantum \ncomputing is a way to perform quantum error correction with imperfect operations while \nretaining the ability to suppress errors as long as the noise is below a code's threshold. \nOne of the main challenges in performing fault-tolerant error correction is the high resource \nrequirements that are needed to obtain very low logical noise rates. With the use of \nflag qubits, this thesis develops new fault-tolerant error correction protocols that are applicable \nto arbitrary distance codes. Various code families are shown to satisfy the requirements \nof flag fault-tolerant error correction. We also provide circuits using a constant number of \nqubits for these codes. It is shown that the proposed flag fault-tolerant method uses fewer \nqubits than previous fault-tolerant error correction protocols. \n \nIt is often the case that the noise afflicting a quantum device cannot be fully characterized. \nFurther, even with some knowledge of the noise, it can be very challenging to use \nanalytic decoding methods to improve the performance of a fault-tolerant scheme. This \nthesis presents decoding schemes using several state of the art machine learning techniques \nwith a focus on fault-tolerant quantum error correction in regimes that are relevant to near \nterm experiments. It is shown that even in low noise rate regimes and with no knowledge \nof the noise, noise can be further suppressed for small distance codes. Limitations of machine \nlearning decoders as well as the classical resources required to perform active error \ncorrection are discussed. \n \nIn many cases, gate times can be much shorter than typical measurement times of \nquantum states. Further, classical decoding of the syndrome information used in quantum \nerror correction to compute recovery operators can also be much slower than gate times. \nFor these reasons, schemes where error correction can be implemented in a frame (known \nas the Pauli frame) have been developed to avoid active error correction. In this thesis, we \ngeneralize previous Pauli frame schemes and show how Clifford frame error correction can \nbe implemented with minimal overhead. Clifford frame error correction is necessary if the \nlogical component of recovery operators were chosen from the Clifford group, but could \nalso be used in randomized benchmarking schemes.
Correcting errors is a vital but expensive component of fault tolerant quantum computation. Standard fault tolerant protocol assumes the implementation of error correction, via syndrome measurements and possible recovery operations, after every quantum gate. In fact, this is not necessary. Here we demonstrate that error correction should be applied more sparingly. We simulate encoded single qubit rotations within the [7,1,3] code and show via fidelity measures that applying error correction after every gate is not desirable. The simulations also shed light on what accuracy can be expected for noisy error correction and thus to what accuracy arbitrary single qubit rotations should be implemented.
Correcting errors is a vital but expensive component of fault-tolerant quantum computation. Standard fault-tolerant protocol assumes the implementation of error correction, via syndrome measurements and possible recovery operations, after every quantum gate. In fact, this is not necessary. Here we demonstrate that error correction should be applied more sparingly. We simulate encoded single-qubit rotations within the [7,1,3] code and show via fidelity measures that applying error correction after every gate is not desirable.
We propose a method for universal fault-tolerant quantum computation using concatenated quantum error correcting codes. The concatenation scheme exploits the transversal properties of two different codes, combining them to provide a means to protect against low-weight arbitrary errors. We give the required properties of the error correcting codes to ensure universal fault tolerance and discuss a particular example using the 7-qubit Steane and 15-qubit Reed-Muller codes. Namely, other than computational basis state preparation as required by the DiVincenzo criteria, our scheme requires no special ancillary state preparation to achieve universality, as opposed to schemes such as magic state distillation. We believe that optimizing the codes used in such a scheme could provide a useful alternative to state distillation schemes that exhibit high overhead costs.
Extensive quantum error correction is necessary in order to perform a useful computation on a noisy quantum computer. Moreover, quantum error correction must be implemented based on imperfect parity check measurements that may return incorrect outcomes or inject additional faults into the qubits. To achieve fault-tolerant error correction, Shor proposed to repeat the sequence of parity check measurements until the same outcome is observed sufficiently many times. Then, one can use this information to perform error correction. A basic implementation of this fault tolerance strategy requires
Ω(rd2)parity check measurements for a distance-
dcode defined by
rparity checks. For some specific highly structured quantum codes, Bombin has shown that single-shot fault-tolerant quantum error correction is possible using only
rmeasurements. In this work, we consider a phenomenological noise model for parity check measurements assuming that each bit of a codeword and the measurement outcome suffer from independent bit flips with some error rate
p. For this model, we demonstrate that fault-tolerant quantum error correction can be achieved using
O(dlog(d))measurements for any code with distance
d≥Ω(nα)for some constant
α>0. Moreover, we prove the existence of a sub-single-shot fault-tolerant quantum error correction scheme using fewer than
rmeasurements. In some cases, the number of parity check measurements required for fault-tolerant quantum error correction is exponentially smaller than the number of parity checks defining the code. The short measurement sequences constructed generally have high weight and our phenomenological noise model is not realistic in this regime. Our error correction strategy could find applications to small codes and LDPC codes if one can manage to keep the weight of the measured parity checks low.