Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:cond-mat/0512428 · Physical Review Letters

Dephasing of a Superconducting Qubit Induced by Photon Noise

Patrice Bertet, I. Chiorescu, Guido Burkard, Kouichi Semba, C. J. P. M. Harmans, David Peter Divincenzo, Johan E. Mooij

Published Dec 13, 2005• 315 citations
arXivHTMLPDF

Abstract

We have studied the dephasing of a superconducting flux qubit coupled to a dc-SQUID based oscillator. By varying the bias conditions of both circuits we were able to tune their effective coupling strength. This allowed us to measure the effect of such a controllable and well-characterized environment on the qubit coherence. We can quantitatively account for our data with a simple model in which thermal fluctuations of the photon number in the oscillator are the limiting factor. In particular, we observe a strong reduction of the dephasing rate whenever the coupling is tuned to zero. At the optimal point we find a large spin-echo decay time of .

DOI
10.1103/physrevlett.95.257002

Related papers

Relaxation and Dephasing in a Flux-qubit

Patrice Bertet, I. Chiorescu, Guido Burkard +4 more

We report detailed measurements of the relaxation and dephasing time in a flux-qubit measured by a switching DC SQUID. We studied their dependence on the two important circuit bias parameters: the externally applied magnetic flux and the bias current through the SQUID in two samples. We demonstrate two complementary strategies to protect the qubit from these decoherence sources. One consists in biasing the qubit so that its resonance frequency is stationary with respect to the control parameters ({\it optimal point}) ; the second consists in {\it decoupling} the qubit from current noise by chosing a proper bias current through the SQUID. At the decoupled optimal point, we measured long spin-echo decay times of up to $4 μs$.

arXiv:cond-mat/0412485•Dec 17, 2004•14 citations

Phase coherent dynamics of a superconducting flux qubit with capacitive bias readout

Frank Deppe, M. Mariantoni, E. P. Menzel +7 more

We present a systematic study of the phase coherent dynamics of a superconducting three-Josephson-junction flux qubit. The qubit state is detected with the integrated-pulse method, which is a variant of the pulsed switching-dc-superconducting quantum interference device (SQUID) method. In this scheme, the dc SQUID bias current pulse is applied via a capacitor instead of a resistor, giving rise to a narrow bandpass instead of a pure low-pass filter configuration of the electromagnetic environment. Measuring one and the same qubit with both setups allows a direct comparison. With the capacitive method about four times faster switching pulses and an increased visibility are achieved. Furthermore, the deliberate engineering of the electromagnetic environment, which minimizes the noise due to the bias circuit, is facilitated. Right at the degeneracy point, the qubit coherence is limited by energy relaxation. We find two main noise contributions. White noise limits the energy relaxation and contributes to the dephasing far from the degeneracy point. $1∕f$ noise is the dominant source of dephasing in the direct vicinity of the optimal point. The influence of $1∕f$ noise is also supported by nonrandom beatings in the Ramsey and spin echo decay traces. Numeric simulations of a coupled qubit-oscillator system indicate that these beatings are due to the resonant interaction of the qubit with at least one pointlike fluctuator, coupled especially strongly to the qubit.

arXiv:0710.4455•Physical Review B•Dec 4, 2007•38 citations

Dephasing of a flux-qubit coupled to a harmonic oscillator

Patrice Bertet, I. Chiorescu, C. J. P. M. Harmans +1 more

Decoherence in superconducting qubits is known to arise because of a variety of environmental degrees of freedom. In this article, we focus on the influence of thermal fluctuations in a weakly damped circuit resonance coupled to the qubit. Because of the coupling, the qubit frequency is shifted by an amount $n δν_0$ if the resonator contains $n$ energy quanta. Thermal fluctuations induce temporal variations $n(t)$ and thus dephasing. We give an approximate formula for the qubit dephasing time as a function of $δν_0$. We discuss the specific case of a flux-qubit coupled to the plasma mode of its DC-SQUID detector. We first derive a plasma mode-qubit interaction hamiltonian which, in addition to the usual Jaynes-Cummings term, has a coupling term quadratic in the oscillator variables coming from the flux-dependence of the SQUID Josephson inductance. Our model predicts that $δν_0$ cancels in certain non-trivial bias conditions for which dephasing due to thermal fluctuations should be suppressed.

arXiv:cond-mat/0507290•Jul 13, 2005•12 citations

Photon shot noise dephasing in the strong-dispersive limit of circuit QED

Adam Sears, Andrei Petrenko, Gianluigi Catelani +7 more

We study the photon shot noise dephasing of a superconducting transmon qubit in the strong-dispersive limit, due to the coupling of the qubit to its readout cavity. As each random arrival or departure of a photon is expected to completely dephase the qubit, we can control the rate at which the qubit experiences dephasing events by varying in situ the cavity mode population and decay rate. This allows us to verify a pure dephasing mechanism that matches theoretical predictions, and in fact explains the increased dephasing seen in recent transmon experiments as a function of cryostat temperature. We observe large increases in coherence times as the cavity is decoupled from the environment, and after implementing filtering find that the intrinsic coherence of small Josephson junctions when corrected with a single Hahn echo is greater than several hundred microseconds. Similar filtering and thermalization may be important for other qubit designs in order to prevent photon shot noise from becoming the dominant source of dephasing.

arXiv:1206.1265•Physical Review B•Nov 12, 2012•155 citations

Control of the transition frequency of a superconducting flux qubit by longitudinal coupling to the photon number degree of freedom in a resonator

Hiraku Toida, Takuya Ohrai, Yuichiro Matsuzaki +2 more

We control the transition frequency of a superconducting flux qubit coupled to a frequency-tunable resonator comprising a direct current superconducting quantum interference device (dc SQUID) by microwave driving. The dc SQUID mediates the coupling between microwave photons in the resonator and a flux qubit. The polarity of the frequency shift depends on the sign of the flux bias for the qubit and can be both positive and negative. The absolute value of the frequency shift becomes larger by increasing the photon number in the resonator. These behaviors are reproduced by a model considering the magnetic interaction between the flux qubit and dc SQUID. The tuning range of the transition frequency of the flux qubit reaches $\ensuremath{\approx}1.9\phantom{\rule{0.16em}{0ex}}\mathrm{GHz}$. The effect of photon number fluctuation in the resonator to the dephasing rate of the flux qubit is also discussed.

arXiv:2005.06155•Physical review. B./Physical review. B•Sep 3, 2020•5 citations

Reducing decoherence in dc SQUID phase qubits

Anthony J. Przybysz

This thesis examines sources of dissipation and dephasing in a dc SQUID phase qubit. Coupling of the qubit to the bias lines and lossy dielectrics causes the qubit to lose quantum information through a process known generally as decoherence. Using knowledge of the possible sources of decoherence, a dc SQUID phase qubit is designed with parameters that should have made it resistant to dissipation and dephasing from those sources. Device PB9 was a dc SQUID with one small area 0.23 (μm)2 Josephson junction with a critical current of 130 nA, which was meant to be the qubit junction, and a larger area 5 (μm)2 junction with a critical current of 8.6 μA, which acted as part of an inductive isolation network. The qubit junction was shunted by a 1.5 pF low-loss interdigitated capacitor. The dc current bias line had an on-chip LC filter with a cutoff frequency of 180 MHz. The other control lines were also designed to minimize coupling of dissipative elements to the qubit. According to a theoretical model of the dissipation and dephasing, the qubit was expected to have an energy relaxation T1 ≤ 8.4 μs and dephasing time Tø ∼ 1 μs. Because of the relatively high Josephson inductance of the qubit junction, the device did not act perform like a conventional isolated single-junction phase qubit. Instead, the resonant modes that I observed were the normal modes of the entire SQUID. At 20 mK and a frequency of 4.047 GHz, the maximum energy relaxation time of the device was found to be 350 ± 70 ns, despite the optimized design. Through a study of T1 versus applied flux, T1 was found to depend on the strength of the coupling of the microwave drive line to the qubit. When the line was more coupled, T1 was shorter. This was evidence that the microwave line was overcoupled to the qubit, and was limiting the lifetime of the excited state T1. Through a study of the spectroscopic coherence time T2* , which measured the effects of low-frequency inhomogeneous broadening and higher frequency dephasing from noise, I discovered that device PB9 has several sweet spots. In particular, the presence of a sweet spot with respect to critical current fluctuations allowed me to identify critical current noise as a major source of broadening and dephasing in the qubit. From the spectroscopy I estimated the 1/f critical current noise power density at 1 Hz was SI01 (1Hz) ≈ 10 (nA) 2/Hz and the 1/f flux noise power spectral density at 1 Hz was SΦ (1Hz) ≈ (110 μΦ 0)2/Hz. Both of these values were quite high, possibly due to switching of the device between measurements.

•Jan 1, 2010•1 citation
We have studied the dephasing of a superconducting flux qubit coupled to a dc-SQUID based oscillator. By varying the bias conditions of both circuits we were able to tune their effective coupling strength. This allowed us to measure the effect of such a controllable and well-characterized environment on the qubit coherence. We can quantitatively account for our data with a simple model in which thermal fluctuations of the photon number in the oscillator are the limiting factor. In particular, we observe a strong reduction of the dephasing rate whenever the coupling is tuned to zero. At the optimal point we find a large spin-echo decay time of .
We report detailed measurements of the relaxation and dephasing time in a flux-qubit measured by a switching DC SQUID. We studied their dependence on the two important circuit bias parameters: the externally applied magnetic flux and the bias current through the SQUID in two samples. We demonstrate two complementary strategies to protect the qubit from these decoherence sources. One consists in biasing the qubit so that its resonance frequency is stationary with respect to the control parameters ({\it optimal point}) ; the second consists in {\it decoupling} the qubit from current noise by chosing a proper bias current through the SQUID. At the decoupled optimal point, we measured long spin-echo decay times of up to 4μs4 μs4μs.
We present a systematic study of the phase coherent dynamics of a superconducting three-Josephson-junction flux qubit. The qubit state is detected with the integrated-pulse method, which is a variant of the pulsed switching-dc-superconducting quantum interference device (SQUID) method. In this scheme, the dc SQUID bias current pulse is applied via a capacitor instead of a resistor, giving rise to a narrow bandpass instead of a pure low-pass filter configuration of the electromagnetic environment. Measuring one and the same qubit with both setups allows a direct comparison. With the capacitive method about four times faster switching pulses and an increased visibility are achieved. Furthermore, the deliberate engineering of the electromagnetic environment, which minimizes the noise due to the bias circuit, is facilitated. Right at the degeneracy point, the qubit coherence is limited by energy relaxation. We find two main noise contributions. White noise limits the energy relaxation and contributes to the dephasing far from the degeneracy point. 1∕f1∕f1∕f noise is the dominant source of dephasing in the direct vicinity of the optimal point. The influence of 1∕f1∕f1∕f noise is also supported by nonrandom beatings in the Ramsey and spin echo decay traces. Numeric simulations of a coupled qubit-oscillator system indicate that these beatings are due to the resonant interaction of the qubit with at least one pointlike fluctuator, coupled especially strongly to the qubit.
Decoherence in superconducting qubits is known to arise because of a variety of environmental degrees of freedom. In this article, we focus on the influence of thermal fluctuations in a weakly damped circuit resonance coupled to the qubit. Because of the coupling, the qubit frequency is shifted by an amount nδν0n δν_0nδν0​ if the resonator contains nnn energy quanta. Thermal fluctuations induce temporal variations n(t)n(t)n(t) and thus dephasing. We give an approximate formula for the qubit dephasing time as a function of δν0δν_0δν0​. We discuss the specific case of a flux-qubit coupled to the plasma mode of its DC-SQUID detector. We first derive a plasma mode-qubit interaction hamiltonian which, in addition to the usual Jaynes-Cummings term, has a coupling term quadratic in the oscillator variables coming from the flux-dependence of the SQUID Josephson inductance. Our model predicts that δν0δν_0δν0​ cancels in certain non-trivial bias conditions for which dephasing due to thermal fluctuations should be suppressed.
We study the photon shot noise dephasing of a superconducting transmon qubit in the strong-dispersive limit, due to the coupling of the qubit to its readout cavity. As each random arrival or departure of a photon is expected to completely dephase the qubit, we can control the rate at which the qubit experiences dephasing events by varying in situ the cavity mode population and decay rate. This allows us to verify a pure dephasing mechanism that matches theoretical predictions, and in fact explains the increased dephasing seen in recent transmon experiments as a function of cryostat temperature. We observe large increases in coherence times as the cavity is decoupled from the environment, and after implementing filtering find that the intrinsic coherence of small Josephson junctions when corrected with a single Hahn echo is greater than several hundred microseconds. Similar filtering and thermalization may be important for other qubit designs in order to prevent photon shot noise from becoming the dominant source of dephasing.
We control the transition frequency of a superconducting flux qubit coupled to a frequency-tunable resonator comprising a direct current superconducting quantum interference device (dc SQUID) by microwave driving. The dc SQUID mediates the coupling between microwave photons in the resonator and a flux qubit. The polarity of the frequency shift depends on the sign of the flux bias for the qubit and can be both positive and negative. The absolute value of the frequency shift becomes larger by increasing the photon number in the resonator. These behaviors are reproduced by a model considering the magnetic interaction between the flux qubit and dc SQUID. The tuning range of the transition frequency of the flux qubit reaches $\ensuremath{\approx}1.9\phantom{\rule{0.16em}{0ex}}\mathrm{GHz}$. The effect of photon number fluctuation in the resonator to the dephasing rate of the flux qubit is also discussed.
This thesis examines sources of dissipation and dephasing in a dc SQUID phase qubit. Coupling of the qubit to the bias lines and lossy dielectrics causes the qubit to lose quantum information through a process known generally as decoherence. Using knowledge of the possible sources of decoherence, a dc SQUID phase qubit is designed with parameters that should have made it resistant to dissipation and dephasing from those sources. Device PB9 was a dc SQUID with one small area 0.23 (μm)2 Josephson junction with a critical current of 130 nA, which was meant to be the qubit junction, and a larger area 5 (μm)2 junction with a critical current of 8.6 μA, which acted as part of an inductive isolation network. The qubit junction was shunted by a 1.5 pF low-loss interdigitated capacitor. The dc current bias line had an on-chip LC filter with a cutoff frequency of 180 MHz. The other control lines were also designed to minimize coupling of dissipative elements to the qubit. According to a theoretical model of the dissipation and dephasing, the qubit was expected to have an energy relaxation T1 ≤ 8.4 μs and dephasing time Tø ∼ 1 μs. Because of the relatively high Josephson inductance of the qubit junction, the device did not act perform like a conventional isolated single-junction phase qubit. Instead, the resonant modes that I observed were the normal modes of the entire SQUID. At 20 mK and a frequency of 4.047 GHz, the maximum energy relaxation time of the device was found to be 350 ± 70 ns, despite the optimized design. Through a study of T1 versus applied flux, T1 was found to depend on the strength of the coupling of the microwave drive line to the qubit. When the line was more coupled, T1 was shorter. This was evidence that the microwave line was overcoupled to the qubit, and was limiting the lifetime of the excited state T1. Through a study of the spectroscopic coherence time T2* , which measured the effects of low-frequency inhomogeneous broadening and higher frequency dephasing from noise, I discovered that device PB9 has several sweet spots. In particular, the presence of a sweet spot with respect to critical current fluctuations allowed me to identify critical current noise as a major source of broadening and dephasing in the qubit. From the spectroscopy I estimated the 1/f critical current noise power density at 1 Hz was SI01 (1Hz) ≈ 10 (nA) 2/Hz and the 1/f flux noise power spectral density at 1 Hz was SΦ (1Hz) ≈ (110 μΦ 0)2/Hz. Both of these values were quite high, possibly due to switching of the device between measurements.