Quantum technology has been exploited to enable a large range of exciting new disciplines including quantum computing, quantum communication and quantum cryptography. Very recently, quantum technology was explored for fine-grained motion sensing and a new concept termed ``quantum wireless sensing'' was proposed. Compared to conventional wireless sensing whose sensing granularity is fundamentally limited by the thermal noise of RF receiver, the thermal noise of a quantum receiver is orders of magnitude smaller. In this article, instead of applying quantum wireless sensing to sense the motion of a target, we apply it to extract the inherent material characteristic of a target to realize fine-grained liquid recognition. By leveraging the unique capability of capturing RF signals in a wide frequency range with a single quantum receiver, we propose a novel double-ratio scheme to address the most critical challenges in liquid recognition, i.e., the measured liquid feature is not just dependent on liquid type but also dependent on other factors such as liquid volume, device-target distance, and container. We further leverage this unique wide frequency range property to hop multiple channels to improve the sensing accuracy and robustness. Comprehensive real-world experiments show that the proposed quantum-based sensing system is able to recognize 17 commonly seen liquids, including very similar ones (e.g., Pepsi and Coke) at an accuracy higher than 99.9%. For milk expiration monitoring, our system can achieve an accuracy of 99.0% for pH value measurements at a granularity of 0.1, which is much finer than that required for expiration monitoring.
Quantum technology has been exploited to enable a large range of exciting new disciplines including quantum computing, quantum communication and quantum cryptography. Very recently, quantum technology was explored for fine-grained motion sensing and a new concept termed ``quantum wireless sensing'' was proposed. Compared to conventional wireless sensing whose sensing granularity is fundamentally limited by the thermal noise of RF receiver, the thermal noise of a quantum receiver is orders of magnitude smaller. In this article, instead of applying quantum wireless sensing to sense the motion of a target, we apply it to extract the inherent material characteristic of a target to realize fine-grained liquid recognition. By leveraging the unique capability of capturing RF signals in a wide frequency range with a single quantum receiver, we propose a novel double-ratio scheme to address the most critical challenges in liquid recognition, i.e., the measured liquid feature is not just dependent on liquid type but also dependent on other factors such as liquid volume, device-target distance, and container. We further leverage this unique wide frequency range property to hop multiple channels to improve the sensing accuracy and robustness. Comprehensive real-world experiments show that the proposed quantum-based sensing system is able to recognize 17 commonly seen liquids, including very similar ones (e.g., Pepsi and Coke) at an accuracy higher than 99.9%. For milk expiration monitoring, our system can achieve an accuracy of 99.0% for pH value measurements at a granularity of 0.1, which is much finer than that required for expiration monitoring.
Recent years have witnessed the use of pervasive wireless signals (e.g., Wi-Fi, RFID, and mmWave) for sensing purposes. Due to its non-intrusive characteristic, wireless sensing plays an important role in various intelligent sensing applications. However, limited by the inherent thermal noise of RF transceivers, the sensing granularity of existing wireless sensing systems are still coarse, limiting their adoption for fine-grained sensing applications. In this paper, we introduce the quantum receiver, which does not contain traditional electronic components such as mixers, amplifiers, and analog-to-digital converters (ADCs) to wireless sensing systems, significantly reducing the source of thermal noise. By taking non-intrusive liquid recognition as an application example, we show the superior performance of quantum wireless sensing. By leveraging the unique property of quantum receiver, we propose a novel double-ratio method to address several well-known challenges in liquid recognition, eliminating the effect of liquid volume, device-target distance and container. We implement the quantum sensing prototype and evaluate the liquid recognition performance comprehensively. The results show that our system is able to recognize 17 commonly seen liquids, including very similar ones~(e.g., Pepsi and Coke) at an accuracy higher than 99.9\%. For milk expiration monitoring, our system is able to achieve an accuracy of 99.0\% for pH value measurements at a granularity of 0.1, which is much finer than that required for expiration monitoring.
Recent years have witnessed a tremendous amount of interest in wireless sensing, i.e., instead of employing traditional sensors, wireless signal is utilized for sensing purposes. Contact-free wireless sensing has been successfully demonstrated using various RF signals such as WiFi, RFID, LoRa, and mmWave, enabling a large range of applications. However, limited by hardware thermal noise, the granularity of RF sensing is still relatively coarse. In this paper, instead of using the macro signal power/phase for sensing, we propose the first quantum wireless sensing system, which uses the micro energy level of atoms for sensing, improving the sensing granularity by an order of magnitude. The proposed quantum wireless sensing system is capable of utilizing a wide spectrum of frequencies (e.g., 2.4 GHz, 5 GHz and 28 GHz) for sensing. We demonstrate the superior performance of quantum wireless sensing with two widely-used signals, i.e., WiFi and 28 GHz millimeter wave. We show that quantum wireless sensing can push the sensing granularity of WiFi from millimeter level to sub-millimeter level and push the sensing granularity of millimeter wave to micrometer level.
Rydberg-atom sensors have emerged as a promising quantum technology for broadband radio-frequency detection owing to their intrinsic calibration, wide frequency coverage, and high sensitivity. However, their potential for intelligent identification of real-world wireless signals remains largely unexplored. Here, we demonstrate a quantum-enabled framework for mobile signal classification based on Rydberg electromagnetically induced transparency spectroscopy and deep learning. Three types of wireless emissions, including cellular voice call, Wi-Fi, and 5G signals from three commercial smartphone brands, are measured to construct a spectral-fingerprint dataset. A convolutional neural network trained on this dataset achieves an initial baseline classification accuracy of 93.44\%. To compensate for spectral drifts induced by temporal and environmental variations, a progressive fine-tuning strategy is employed to continuously adapt the pretrained model, enabling robust classification across diverse deployment scenarios. Furthermore, continuous real-time monitoring is demonstrated under dynamically varying wireless conditions, including cellular voice call, Wi-Fi, and their coexistence. The proposed system achieves an overall frame-level recognition accuracy of 87.67\% over a 60-s measurement. These results establish a pathway toward intelligent quantum radio-frequency sensing and highlight the potential of Rydberg-atom platforms for real-time wireless signal awareness and spectrum monitoring.
The significant progress of quantum sensing technologies offer numerous radical solutions for measuring a multitude of physical quantities at an unprecedented precision. Among them, Rydberg atomic quantum receivers (RAQRs) emerge as an eminent solution for detecting the electric field of radio frequency (RF) signals, exhibiting great potential in assisting classical wireless communications and sensing. So far, most experimental studies have aimed for the proof of physical concepts to reveal its promise, while the practical signal model of RAQR-aided wireless communications and sensing remained under-explored. Furthermore, the performance of RAQR-based wireless receivers and their advantages over classical RF receivers have not been fully characterized. To fill these gaps, we introduce the RAQR to the wireless community by presenting an end-to-end reception scheme. We then develop a corresponding equivalent baseband signal model relying on a realistic reception flow. Our scheme and model provide explicit design guidance to RAQR-aided wireless systems. We next study the performance of RAQR-aided wireless systems based on our model, and compare them to classical RF receivers. The results show that Doppler broadening-free RAQRs are capable of achieving a substantial received signal-to-noise ratio (SNR) gain of over 27 decibel (dB) and 40 dB in the photon shot limit and standard quantum limit regimes, respectively.
In recent years, wireless sensing has garnered increasing attention from both industry and academia. Despite its promise, it still faces several fundamental challenges that are difficult to overcome, including hardware thermal noise limitation, antenna size constraint, and limited frequency band resources. At the same time, rapid advancements in quantum technology are driving continuous innovations. By thoroughly understanding the principles of both wireless sensing and quantum physics, we propose a novel paradigm: quantum wireless sensing. Although quantum wireless sensing originates from quantum measurement, its focus has shifted toward practical wireless sensing tasks. This evolution calls for a reassessment of parameter estimation, grounded in the fundamental principles of quantum physics. We believe the unique advantages of quantum receivers - specifically, their high sensitivity and wide frequency range - can unlock powerful quantum sensing capabilities across various domains, including terrestrial, aerospace, and maritime applications. This article articulates our vision for this emerging field, highlighting recent advancements in quantum wireless sensing and exploring promising directions for future research.
Rydberg atomic quantum receivers (RAQRs) are emerging quantum precision sensing platforms designed for receiving radio frequency (RF) signals. It relies on the creation of Rydberg atoms from normal atoms by exciting one or more electrons to a very high energy level, thereby making the atom sensitive to RF signals. RAQRs realize RF-to-optical conversions based on atom-light interactions relying on the so-called electromagnetically induced transparency (EIT) and Autler- Townes splitting (ATS) so that the desired RF signal can be read out optically. The large dipole moments of Rydberg atoms associated with rich choices of Rydberg states facilitate an ultra-high sensitivity (~nv⁄cm/√Hz) and an ultra-broadband tunability (direct-current to Terahertz). RAQRs also exhibit compelling scalability and lend themselves to the construction of innovative, compact receivers. Initial experimental studies have demonstrated their capabilities in classical wireless communications and sensing. To fully harness their potential in a wide variety of applications, we commence by outlining the underlying fundamentals of Rydberg atoms, followed by the principles and schemes of RAQRs. Then, we overview the state-of-the-art studies from both physics and communication societies. Furthermore, we conceive Rydberg atomic quantum single-input single-output (RAQ-SISO) and multiple-input multiple- output (RAQ-MIMO) schemes to facilitate the integration of RAQRs with classical wireless systems. Finally, we conclude with a set of potent research directions.