Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Towards Selective Two-step Photoionization of Ba Isotopes for Ba+ Ion Trap

Tamura Koji, Ogura Koichi, Shimada Hiroyuki, Kashiwagi Hirotsugu, Hosaka Koichi, Nakanishi Ryuzo, Yuri Yosuke, Narumi Kazumasa

Published Jul 4, 2024• 0 citations
OpenAlex

Abstract

Cooling and trapping ion system is considered as a promising candidate for quantum information processor. Especially, by manipulating 133Ba+ ion, improved fidelity of qubit operation is expected, where selective 133Ba isotope introduction to the ion trap is required. Development of isotope selective loading system of Ba ion for the ion trap using the two-step laser photoionization is shown. For the excitation step (791 nm), the target isotope atom is photo-excited among other Ba isotopes based on their isotope shift. A tunable laser with a narrow spectral linewidth compared to the Ba isotope shift, was developed using an external cavity diode laser (ECDL). Mode-hop-free (MHF) scanning was achieved. For the second ionization step, a pulsed N2 laser was used. Both laser beams were combined using a mirror, focused with a lens, and introduced into a vacuum chamber. An atomic source was made by resistive heating, which can heat the source and generate atomic beam with sufficient vapor pressure and atomic density for the measurements. The system is under development and is prepared for the Ba atomic beam generation and laser photoionization experiments.

Related papers

Isotope-selective laser ablation ion-trap loading of Ba+137 using a BaCl2 target

Brendan White, Pei Jiang Low, Yvette de Sereville +4 more

The $^{133}\mathrm{Ba}^{+}$ ion is a promising candidate as a high-fidelity qubit, and the $^{137}\mathrm{Ba}^{+}$ isotope is promising as a high-fidelity qudit $(d>2)$. Barium metal is very reactive, and $^{133}\mathrm{Ba}^{+}$ is radioactive and can only be sourced in small quantities, so the most commonly used loading method, oven heating, is less suited for barium and is currently not possible for $^{133}\mathrm{Ba}^{+}$. Pulsed laser ablation solves both of these problems by utilizing compound barium sources while also giving some distinct advantages, such as fast loading, less displaced material, and lower heat load near the ion trap. Because of the relatively low abundances of the isotopes of interest, a two-step photoionization technique is used, which gives us the ability to selectively load isotopes. Characterization of the ablation process for our ${\mathrm{BaCl}}_{2}$ targets are presented, including observation of neutral and ion ablation-fluence regimes, preparation and conditioning, lifetimes of ablation spots, and plume velocity distributions. We show that by using laser ablation on ${\mathrm{BaCl}}_{2}$ salt targets with a two-step photoionization method, we can produce and trap barium ions reliably. Furthermore, we demonstrate that with our photoionization method, we can trap $^{137}\mathrm{Ba}^{+}$ with an enhanced selectivity compared to its natural abundance.

arXiv:2110.08456•Physical Review A•Mar 9, 2022•17 citations

Rapid high-purity loading of barium ion via relayed selectivity from naturally abundant source

Zichun Zhou, Xuhui Yao, Jiaze Li +5 more

Trapped ions is one of the promising platforms for realizing quantum information processing and quantum simulation. Selective and rapid loading of a specific isotope lays the critical foundation for such purpose particularly when scaling up the system size. Here we demonstrate a new method for rapid isotope-selective loading of $^{137}\mathrm{Ba}^{+}$ or $^{135}\mathrm{Ba}^{+}$, two types of promising ion qubits, from naturally abundant source using a three-step, ultraviolet-free photoionization scheme. Neutral atoms are selected on the narrow 791 nm $6s^2\,{}^1S_0\rightarrow6s6p\,{}^3P_1^o$ transition, resonantly transferred at 554 nm to $6s6d\,{}^3D_1$, and ionized using an existing 532 nm Raman beam. A spectral-overlap analysis based on isotope and hyperfine shifts shows relayed selectivity that the second step can further suppress undesired-isotope excitation and no contaminant ion is detected during our entire experiment. Besides, the resonant drive of the second step excitation yields a prominent loading rate of the selected species. This strategy using multi-step excitations to establish relayed selectivity can be extended to high-purity loading of other species of ions.

arXiv:2611.11990•Nov 9, 2026•0 citations

Ionisation and state preparation for single ion experiments

Thomas Lafenthaler

Trapped single ions provide an ideal platform for studying quantum optics, light-matter interactions, and quantum information processing. Many of these applications rely on the availability of well-defined and reproducible quantum emitters as well as precise control over the internal states of ions. To study both of these concepts, this thesis focuses on the isotope selectivity of neutral Barium (Ba) transitions as well as the state preparation of single trapped 138Ba+ ions. The first part of this thesis introduces the theoretical framework for experiments, focusing on single Ba+ ions and light-matter interactions. Therefore, the working principle of Paul traps is presented, the Ba ion is introduced and fundamental light-matter interaction tightly related to the experiments and simulations presented in this work are established. In the second part, the isotope selectivity of the neutral Ba 6s2 1S0 to 6s6p 1P1 transition at 553 nm is investigated and compared with the isotope selectivity of the 6s2 1S0 to 5d6p 3D1 transition at 413 nm. A secondary photon can be used in both cases to achieve isotope selective ionization of Ba+ ions. The isotope selectivity of the 553 nm transition was tested by carrying out spectroscopy and comparing the results with existing data. The isotope selectivity for other naturally available Ba isotopes is simulated for both transitions (553 nm and 413 nm) and for different angles between atomic beam and laser beam (90°, 85° and 80°). The simulations show, that under ideal conditions (when the atomic beam and ionization laser beam are orthogonal) both transitions perform similarly. However, the 553 nm transition exhibits greater robustness against Doppler shifts as the angle deviates from 90°. At an angle of 80° between the atomic beam and the laser beam, the maximum probability of generating 138Ba+ is 99 % using 553 nm, while the maximum probability of generating the isotope using 413 nm does not exceed 94 %. In the third part of this thesis, we focus on state preparation of Ba+ ions in the 6P1/2 state. A heralding state preparation scheme that exploits the spontaneous emission of a 389 nm photon during the decay of the excited state 6D3/2 is introduced. The detection of a photon at this wavelength projects the ion into the desired state 6P1/2 in a deterministic fashion. A simulation of this scheme shows that the preparation probability may exceed 78 %, and the heralding process ensures state preparation with 100 % fidelity, if a photon at a wavelength of 389 nm is detected. The state preparation method will be adopted in near-future experiments that are provided as an outlook at the end of this thesis.

•Jan 1, 2026•0 citations

Trapping Ba+ with seven-fold enhanced efficiency utilizing an autoionizing resonance

Noah Greenberg, Brendan White, Pei Jiang Low +1 more

Abstract Trapped ions have emerged as a front runner in quantum information processing due to their identical nature, all-to-all connectivity, and high fidelity quantum operations. As current trapped ion technologies are scaled, it will be important to improve the efficiency of loading ions, especially when working with long chains of ions or rare isotopes. Here, we compare two different isotope-selective photoionization schemes for loading 138 Ba + ions. We show that a two-step photoionization scheme ending in an autoionizing transition increases the ion loading rate nearly an order of magnitude compared to an established technique which does not excite an autoionizing state. Our novel photoionization scheme can be extended to all isotopes of barium. Given that autoionizing resonances exist in every trapped ion species, exploitation of this process is a promising pathway to increase the loading rates for trapped ion computers.

arXiv:2307.07627•Quantum Science and Technology•Apr 16, 2024•4 citations

Isotope-selective photoionization for calcium ion trapping

D. Lucas, A. Ramos, Jonathan Home +6 more

We present studies of resonance-enhanced photoionization for isotope-selective loading of ${\mathrm{Ca}}^{+}$ into a Paul trap. The ${4s}^{2}{}^{1}{S}_{0}\ensuremath{\leftrightarrow}4s4p{}^{1}{P}_{1}$ transition of neutral calcium is driven by a 423 nm laser and the atoms are photoionized by a second laser at 389 nm. Isotope selectivity is achieved by using crossed atomic and laser beams to reduce the Doppler width significantly below the isotope shifts in the 423 nm transition. The loading rate of ions into the trap is studied under a range of experimental parameters for the abundant isotope ${}^{40}{\mathrm{Ca}}^{+}.$ Using the fluorescence of the atomic beam at 423 nm as a measure of the Ca number density, we estimate a lower limit for the absolute photoionization cross section of 170(60) Mb. We achieve loading and laser cooling of all the naturally occurring isotopes, without the need for enriched sources. Laser heating/cooling is observed to enhance the isotope selectivity. In the case of the rare species ${}^{43}{\mathrm{Ca}}^{+}$ and ${}^{46}{\mathrm{Ca}}^{+},$ which have not previously been laser cooled, the loading is not fully isotope selective, but we show that pure crystals of ${}^{43}{\mathrm{Ca}}^{+}$ may nevertheless be obtained. We find that for loading ${}^{40}{\mathrm{Ca}}^{+}$ the 389 nm laser may be replaced by an incoherent source.

arXiv:physics/0310044•Physical Review A•Jan 1, 2004•160 citations

Selective Loading of Rare Calcium Isotope 43Ca+ using Photo-Ionization

Isamu Morita, U. Tanaka, Shinji Urabe

Rare calcium isotope 43Ca+ ion (0.135%) is the only naturally abundant isotope with hyperfine structure. This isotope is considered an attractive candidate both for an optical frequency standard and for quantum information processing. We report a method to load 43Ca+ ions selectively into a linear Paul trap using a two-step, resonant photo-ionization process. Isotope selectivity is achieved by utilizing the isotope shifts for the resonant 4s2 1S0-4s4p 1P1 transition of neutral calcium. The second non-resonant excitation is achieved by an ultraviolet light emitting diode (LED). The use of an LED is simpler and more economical than using a laser for the second transition. Additionally the laser cooling of 43Ca+ is demonstrated using two ultraviolet-diode lasers and two infrared-diode lasers. Due to the hyperfine structure, the laser requirements for Doppler cooling 43Ca+ are more demanding than for the other isotopes.

The Review of Laser Engineering•Jan 1, 2007•0 citations
Cooling and trapping ion system is considered as a promising candidate for quantum information processor. Especially, by manipulating 133Ba+ ion, improved fidelity of qubit operation is expected, where selective 133Ba isotope introduction to the ion trap is required. Development of isotope selective loading system of Ba ion for the ion trap using the two-step laser photoionization is shown. For the excitation step (791 nm), the target isotope atom is photo-excited among other Ba isotopes based on their isotope shift. A tunable laser with a narrow spectral linewidth compared to the Ba isotope shift, was developed using an external cavity diode laser (ECDL). Mode-hop-free (MHF) scanning was achieved. For the second ionization step, a pulsed N2 laser was used. Both laser beams were combined using a mirror, focused with a lens, and introduced into a vacuum chamber. An atomic source was made by resistive heating, which can heat the source and generate atomic beam with sufficient vapor pressure and atomic density for the measurements. The system is under development and is prepared for the Ba atomic beam generation and laser photoionization experiments.
The 133Ba+^{133}\mathrm{Ba}^{+}133Ba+ ion is a promising candidate as a high-fidelity qubit, and the 137Ba+^{137}\mathrm{Ba}^{+}137Ba+ isotope is promising as a high-fidelity qudit (d>2)(d>2)(d>2). Barium metal is very reactive, and 133Ba+^{133}\mathrm{Ba}^{+}133Ba+ is radioactive and can only be sourced in small quantities, so the most commonly used loading method, oven heating, is less suited for barium and is currently not possible for 133Ba+^{133}\mathrm{Ba}^{+}133Ba+. Pulsed laser ablation solves both of these problems by utilizing compound barium sources while also giving some distinct advantages, such as fast loading, less displaced material, and lower heat load near the ion trap. Because of the relatively low abundances of the isotopes of interest, a two-step photoionization technique is used, which gives us the ability to selectively load isotopes. Characterization of the ablation process for our BaCl2{\mathrm{BaCl}}_{2}BaCl2​ targets are presented, including observation of neutral and ion ablation-fluence regimes, preparation and conditioning, lifetimes of ablation spots, and plume velocity distributions. We show that by using laser ablation on BaCl2{\mathrm{BaCl}}_{2}BaCl2​ salt targets with a two-step photoionization method, we can produce and trap barium ions reliably. Furthermore, we demonstrate that with our photoionization method, we can trap 137Ba+^{137}\mathrm{Ba}^{+}137Ba+ with an enhanced selectivity compared to its natural abundance.
Trapped ions is one of the promising platforms for realizing quantum information processing and quantum simulation. Selective and rapid loading of a specific isotope lays the critical foundation for such purpose particularly when scaling up the system size. Here we demonstrate a new method for rapid isotope-selective loading of 137Ba+^{137}\mathrm{Ba}^{+}137Ba+ or 135Ba+^{135}\mathrm{Ba}^{+}135Ba+, two types of promising ion qubits, from naturally abundant source using a three-step, ultraviolet-free photoionization scheme. Neutral atoms are selected on the narrow 791 nm 6s2 1S0→6s6p 3P1o6s^2\,{}^1S_0\rightarrow6s6p\,{}^3P_1^o6s21S0​→6s6p3P1o​ transition, resonantly transferred at 554 nm to 6s6d 3D16s6d\,{}^3D_16s6d3D1​, and ionized using an existing 532 nm Raman beam. A spectral-overlap analysis based on isotope and hyperfine shifts shows relayed selectivity that the second step can further suppress undesired-isotope excitation and no contaminant ion is detected during our entire experiment. Besides, the resonant drive of the second step excitation yields a prominent loading rate of the selected species. This strategy using multi-step excitations to establish relayed selectivity can be extended to high-purity loading of other species of ions.
Trapped single ions provide an ideal platform for studying quantum optics, light-matter interactions, and quantum information processing. Many of these applications rely on the availability of well-defined and reproducible quantum emitters as well as precise control over the internal states of ions. To study both of these concepts, this thesis focuses on the isotope selectivity of neutral Barium (Ba) transitions as well as the state preparation of single trapped 138Ba+ ions. The first part of this thesis introduces the theoretical framework for experiments, focusing on single Ba+ ions and light-matter interactions. Therefore, the working principle of Paul traps is presented, the Ba ion is introduced and fundamental light-matter interaction tightly related to the experiments and simulations presented in this work are established. In the second part, the isotope selectivity of the neutral Ba 6s2 1S0 to 6s6p 1P1 transition at 553 nm is investigated and compared with the isotope selectivity of the 6s2 1S0 to 5d6p 3D1 transition at 413 nm. A secondary photon can be used in both cases to achieve isotope selective ionization of Ba+ ions. The isotope selectivity of the 553 nm transition was tested by carrying out spectroscopy and comparing the results with existing data. The isotope selectivity for other naturally available Ba isotopes is simulated for both transitions (553 nm and 413 nm) and for different angles between atomic beam and laser beam (90°, 85° and 80°). The simulations show, that under ideal conditions (when the atomic beam and ionization laser beam are orthogonal) both transitions perform similarly. However, the 553 nm transition exhibits greater robustness against Doppler shifts as the angle deviates from 90°. At an angle of 80° between the atomic beam and the laser beam, the maximum probability of generating 138Ba+ is 99 % using 553 nm, while the maximum probability of generating the isotope using 413 nm does not exceed 94 %. In the third part of this thesis, we focus on state preparation of Ba+ ions in the 6P1/2 state. A heralding state preparation scheme that exploits the spontaneous emission of a 389 nm photon during the decay of the excited state 6D3/2 is introduced. The detection of a photon at this wavelength projects the ion into the desired state 6P1/2 in a deterministic fashion. A simulation of this scheme shows that the preparation probability may exceed 78 %, and the heralding process ensures state preparation with 100 % fidelity, if a photon at a wavelength of 389 nm is detected. The state preparation method will be adopted in near-future experiments that are provided as an outlook at the end of this thesis.
Abstract Trapped ions have emerged as a front runner in quantum information processing due to their identical nature, all-to-all connectivity, and high fidelity quantum operations. As current trapped ion technologies are scaled, it will be important to improve the efficiency of loading ions, especially when working with long chains of ions or rare isotopes. Here, we compare two different isotope-selective photoionization schemes for loading 138 Ba + ions. We show that a two-step photoionization scheme ending in an autoionizing transition increases the ion loading rate nearly an order of magnitude compared to an established technique which does not excite an autoionizing state. Our novel photoionization scheme can be extended to all isotopes of barium. Given that autoionizing resonances exist in every trapped ion species, exploitation of this process is a promising pathway to increase the loading rates for trapped ion computers.
We present studies of resonance-enhanced photoionization for isotope-selective loading of Ca+{\mathrm{Ca}}^{+}Ca+ into a Paul trap. The ${4s}^{2}{}^{1}{S}_{0}\ensuremath{\leftrightarrow}4s4p{}^{1}{P}_{1}$ transition of neutral calcium is driven by a 423 nm laser and the atoms are photoionized by a second laser at 389 nm. Isotope selectivity is achieved by using crossed atomic and laser beams to reduce the Doppler width significantly below the isotope shifts in the 423 nm transition. The loading rate of ions into the trap is studied under a range of experimental parameters for the abundant isotope 40Ca+.{}^{40}{\mathrm{Ca}}^{+}.40Ca+. Using the fluorescence of the atomic beam at 423 nm as a measure of the Ca number density, we estimate a lower limit for the absolute photoionization cross section of 170(60) Mb. We achieve loading and laser cooling of all the naturally occurring isotopes, without the need for enriched sources. Laser heating/cooling is observed to enhance the isotope selectivity. In the case of the rare species 43Ca+{}^{43}{\mathrm{Ca}}^{+}43Ca+ and 46Ca+,{}^{46}{\mathrm{Ca}}^{+},46Ca+, which have not previously been laser cooled, the loading is not fully isotope selective, but we show that pure crystals of 43Ca+{}^{43}{\mathrm{Ca}}^{+}43Ca+ may nevertheless be obtained. We find that for loading 40Ca+{}^{40}{\mathrm{Ca}}^{+}40Ca+ the 389 nm laser may be replaced by an incoherent source.
Rare calcium isotope 43Ca+ ion (0.135%) is the only naturally abundant isotope with hyperfine structure. This isotope is considered an attractive candidate both for an optical frequency standard and for quantum information processing. We report a method to load 43Ca+ ions selectively into a linear Paul trap using a two-step, resonant photo-ionization process. Isotope selectivity is achieved by utilizing the isotope shifts for the resonant 4s2 1S0-4s4p 1P1 transition of neutral calcium. The second non-resonant excitation is achieved by an ultraviolet light emitting diode (LED). The use of an LED is simpler and more economical than using a laser for the second transition. Additionally the laser cooling of 43Ca+ is demonstrated using two ultraviolet-diode lasers and two infrared-diode lasers. Due to the hyperfine structure, the laser requirements for Doppler cooling 43Ca+ are more demanding than for the other isotopes.