Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

International Conference on Advanced Computing and Knowledge Engineering (ICACKE)

Parameter Extraction and Performance Assessment of SPCMs for Quantum Communication Applications

J. Suneetha, Smita Darandale

Published Jul 1, 2026• 0 citations
Publisher

Abstract

The performance of the entire link of the quantum communication systems is highly dependent on the quality of the Single photon counting module (SPCM) used in the detection unit. Since the performance of these detectors has to be verified by the manufacturers and researchers, there is a need to use a reliable method for determining their primary performance parameters. In this research, we propose an evaluation setup that is able to determine a number of key parameters such as Dead Time, Photon Detection Efficiency (PDE), After-Pulse Probability (APP), and Dark Count Rate (DCR) without using complicated instrumentation. The proposed evaluation setup uses an FPGA platform that not only synchronizes the operation of the quantum light source with the SPCM but also enables the measurement of the required parameters with a high degree of accuracy. The proposed procedures describe the techniques for extracting the parameters and the mathematical expressions required for their determination.

DOI
10.1109/icacke65470.2026.11651209

Related papers

Simulation for Performance Evaluation of Satellite-Based Quantum Communication System

Adil Fadhil Mushatet, Shelan Khasro Tawfeeq, Axel Sikora

The selection and assessment of single-photon detection modules is a crucial problem in satellite-based QKD systems. The system's overall efficiency, secure key rate and quantum bit error rate are all significantly influenced by single-photon detection modules. There is a knowledge gap about the practical performance of commercially available single-photon detectors because existing research frequently relies on theoretical characteristics. This paper introduces a study on the effect of the parameters of three commercial single photon detection modules from ID Quantique company: ID Qube, ID100, and ID281 on certain Bennett-Brassard 1984 protocol parameters such as secure key rate, mean photon number per pulse, quantum bit error rate, link efficiency and zenith angle with the presence of link and geometrical losses for a downlink geostationary satellite. The study accounts for link and geometrical losses, zenith angle, and mean photon number per pulse. Results indicate that the ID281 detector outperforms the other two in maintaining a better secure key rate and quantum bit error rate, while ID100 shows superior performance in shorter wavelength ranges suitable for downlink operations. The findings suggest that global quantum key distribution coverage is achievable using geostationary satellites. To the best of our knowledge, there has been no prior study that has introduced using real parameters of commercial SPDMs to evaluate secure key rate for quantum key distribution systems based on downlink geostationary satellite

Kufa Journal of Engineering•Nov 1, 2025•2 citations

Detection of ultra-weak laser pulses by free-running single-photon detectors: Modeling dead time and dark counts effects

Hristina Georgieva, Alice Meda, S. M. F. Raupach +6 more

In quantum communication systems, the precise estimation of the detector´s response to the incoming light is necessary to avoid security breaches. The typical working regime uses a free-running single-photon avalanche diode in combination with attenuated laser pulses at telecom wavelength for encoding information. We demonstrate the validity of an analytical model for this regime that considers the effects of dark counts and dead time on the measured count rate. For the purpose of gaining a better understanding of these effects, the photon detections were separated from the dark counts via a software-induced gating mechanism. The model was verified by experimental data for mean photon numbers covering three orders of magnitude as well as for laser repetition frequencies below and above the inverse dead time. Consequently, our model would be of interest for predicting the detector response not only in the field of quantum communications, but also in any other quantum physics experiment where high detection rates are needed.

arXiv:2104.08004•Applied Physics Letters•Apr 26, 2021•22 citations

Photon statistics of light fields based on single-photon-counting modules

Geng-Yuan Li, T. C. Zhang, Y. Li +1 more

Single-photon-counting modules (SPCM's), with their high quantum efficiency, have been widely used to investigate effectively the photon statistics of various light sources, such as the single-photon state and emission light from controlled molecules, atoms, and quantum dots. However, such SPCM's cannot distinguish the arrivals of one photon and two (or more than two) photons at a moment, which makes measurement correction in real experiments. We analyze the effect of SPCM's on photon statistics based on the Hanbury-Brown-Twiss configuration when the total efficiency and background are considered, and it shows that the measured second-order degree of coherence and Mandel $Q$ factor for different quantum states, including single-photon states and squeezed vacuum states, are corrected in different forms. A way of determining the squeezing of a squeezed vacuum state based on single-photon detection is presented.

Physical Review A•Feb 11, 2005•23 citations

Single-photon detectors for satellite based quantum communications

Nigar Sultana

With the growing use of online communications in our modern society, information security is becoming a big concern. Along with that, the progress in quantum computers is posing severe threats to such communications. Once powerful quantum computers are available, most of today's encryption schemes, which are based on computationally hard problems, will be broken within a short period. Researchers are therefore making a great effort to establish quantum-safe encryption schemes. One such scheme is quantum key distribution (QKD), which utilizes the laws of quantum mechanics. These cryptography protocols offer unconditional security to the communication between two distant parties by providing a secure way of sharing encryption keys between them. While over the last few decades QKD has continuously progressed, it is limited to a distance of up to several hundred kilometers using terrestrial quantum links. Satellites are therefore being considered to extend the QKD range for global coverage, although implementations of the satellite-based QKD infrastructure are still in their early stage. There are many aspects of QKD that need further assessment and advancement for establishing long-term satellite-based quantum communication (QC). My thesis works were focused on developing advanced systems for single-photon detectors and quantum sources. Single-photon avalanche diodes (SPADs) are the most viable option for satellite-based quantum communications. They must travel to outer space either for receiving quantum-states in the ground-to-satellite QC or for characterizing the quantum-sources in the satellite-to-ground QC. However, while in space, SPADs exhibit damage caused by the space radiation that gradually increases their dark counts. Performing QKD is not possible when the dark counts exceed a specific threshold. Hence, methods of reducing the detectors' dark counts by mitigating the damages would help to extend the SPADs' in-space useful lifetime. Laser annealing is one such effective method, found in lab experiments, to heal the radiation-induced detector damages. We now aim to carry out this method in low Earth orbit (LEO) to verify its in-orbit effectiveness. On that goal, we are building an annealing payload (APL) for a cube satellite (CubeSat) in collaboration with the University of Illinois at Urbana Champaign (UIUC). We, the University of Waterloo team, built one of the two segments of the APL-- a space-qualified detector module containing two Excelitas C30902SH and Excelitas SLiK detectors. Our miniaturized and compact module integrates the facilities required for the detector operation and laser annealing, as well as an active detector temperature control system. The operation of the detector module is highly flexible and software controllable. Our detector module will work together with the control board containing the laser annealing system (built by the UIUC team). Once the satellite has been launched in 2020, the in-orbit experiment will enable us to study the in-space SPAD radiation damage and their healing using the integrated annealing system. During a second project, we designed and built a new simple readout circuit for the negative feedback avalanche diodes (NFADs), which are free-running single-photon detectors at telecom wavelengths. These detectors suffer from strong afterpulsing effects, which limits their overall performances. Therefore, our readout system incorporates features to suppress NFAD afterpulses. We also used this custom readout to characterize two NFADs (from Princeton Lightwave) and assessed the performance of the new electronics. Our analysis showed that even at higher detection efficiencies, a 20 $\\mu$s hold-off time after each avalanche event is enough to extensively reduce the number of afterpulses and to keep the dark count rate below 100 Hz at 192 K temperature. Both the detectors showed timing jitter of less than 75 ps FWHM at their maximum efficiencies. The best figure of merit is found to be 1.6$\\times 10^7$, which is comparable to that of the high-performing superconducting nanowire single-photon detectors. This result demonstrates the suitability of our readout and the NFADs in various quantum optics applications, such as in long-distance quantum key distribution, where the detection rate is usually low. We then performed a blinding attack, which enables an Eavesdropper in QKD to gain information on the key, on these NFADs using bright illumination. These detectors are usually threshold detectors that generate a click when the optical power is above a certain threshold, otherwise they do not click. Blinding attack utilizes detectors' inability to resolve the photon numbers. During the experiment, we sent controlled optical pulses with a high time resolution to deterministically force detection at the detectors. The result demonstrated the NFADs' susceptibility to these attacks, which tells us to include countermeasures into the system to protect the communications. Finally, we built a quantum source to produce 785 nm polarized photons to implement decoy-state BB84 QKD. Our source utilized the sum-frequency generation scheme to generate 785 nm laser pulses. Its modulator system includes an intensity modulator and two-phase modulators in the Mach-Zehnder configuration to prepare polarized quantum states with different intensities. Our source provides a repetition rate of 500 MHz, which was successfully used in an airborne QKD demonstration with a moving receiver up to $10~ km$ distance. To summarize, my research projects are a contribution to the development of advanced devices, particularly single-photon detectors for quantum communications.

•Jan 23, 2020•2 citations

An efficient performance evaluation modeling tool for SNSPD used in QKD systems

Adil Fadhil Mushatet, Shelan Khasro Tawfeeq

Single-photon detection concept is the most crucial and often difficult factor to determine the performance of quantum key distribution (QKD) systems. One solution to facilitate understanding this concept is to create a virtual environment for modeling, analyzing, and investigating the performance of single photon detectors. In this paper, a simulator for superconducting single photon detectors with time domain visualizer and configurable parameters is presented. The widely used ID281SNSPD in the QKD area was theoretically modeled in terms of pulse analysis, the impact of biasing current and the temperature on the dark counts rate and single photon-detection efficiency and influence of the number of photons per pulse on the single photon-detection efficiency. The simulated results were in good agreement with the theoretical results and the simulator demonstrated its adaptability.

International Journal of Quantum Information•Oct 1, 2019•3 citations

High-efficiency single-photon detectors

Paul G. Kwiat, Aephraim M. Steinberg, R. Y. Chiao +2 more

Using correlated photon pairs produced via spontaneous parametric down-conversion, we have measured the absolute single-photon detection efficiencies and time responses of four detectors: two solid-state photomultipliers (SSPM's) manufactured by Rockwell International Corp., and two custom-modified single-photon counting modules (SSPM's) manufactured by EG, Canada. The highest observed efficiencies were 70.9\ifmmode\pm\else\textpm\fi{}1.9% (with an SSPM, at a wavelength of 632 nm) and 76.4\ifmmode\pm\else\textpm\fi{}2.3% (with an SPCM, at 702 nm). We believe these to be the highest reported single-photon detection efficiencies in the visible spectrum; they are important for quantum cryptography and loophole-free tests of Bell's inequalities, as well as more prosaic applications such as photon correlation spectroscopy and velocimetry. We found that the time profile for coincidences between the SSPM and the SPCM consisted of a main peak with a 3.5-ns full width at half maximum (FWHM) preceded by a smaller peak by 11 ns. A similar time profile between two SPCM's displayed only one peak, with a 300-ps FWHM. Afterpulses were detected in the SPCM's at a level of less than ${10}^{\mathrm{\ensuremath{-}}4}$ of the counting rate, with an exponential decay time constant of 4.5 \ensuremath{\mu}s.

Physical Review A•Aug 1, 1993•107 citations
The performance of the entire link of the quantum communication systems is highly dependent on the quality of the Single photon counting module (SPCM) used in the detection unit. Since the performance of these detectors has to be verified by the manufacturers and researchers, there is a need to use a reliable method for determining their primary performance parameters. In this research, we propose an evaluation setup that is able to determine a number of key parameters such as Dead Time, Photon Detection Efficiency (PDE), After-Pulse Probability (APP), and Dark Count Rate (DCR) without using complicated instrumentation. The proposed evaluation setup uses an FPGA platform that not only synchronizes the operation of the quantum light source with the SPCM but also enables the measurement of the required parameters with a high degree of accuracy. The proposed procedures describe the techniques for extracting the parameters and the mathematical expressions required for their determination.
The selection and assessment of single-photon detection modules is a crucial problem in satellite-based QKD systems. The system's overall efficiency, secure key rate and quantum bit error rate are all significantly influenced by single-photon detection modules. There is a knowledge gap about the practical performance of commercially available single-photon detectors because existing research frequently relies on theoretical characteristics. This paper introduces a study on the effect of the parameters of three commercial single photon detection modules from ID Quantique company: ID Qube, ID100, and ID281 on certain Bennett-Brassard 1984 protocol parameters such as secure key rate, mean photon number per pulse, quantum bit error rate, link efficiency and zenith angle with the presence of link and geometrical losses for a downlink geostationary satellite. The study accounts for link and geometrical losses, zenith angle, and mean photon number per pulse. Results indicate that the ID281 detector outperforms the other two in maintaining a better secure key rate and quantum bit error rate, while ID100 shows superior performance in shorter wavelength ranges suitable for downlink operations. The findings suggest that global quantum key distribution coverage is achievable using geostationary satellites. To the best of our knowledge, there has been no prior study that has introduced using real parameters of commercial SPDMs to evaluate secure key rate for quantum key distribution systems based on downlink geostationary satellite
In quantum communication systems, the precise estimation of the detector´s response to the incoming light is necessary to avoid security breaches. The typical working regime uses a free-running single-photon avalanche diode in combination with attenuated laser pulses at telecom wavelength for encoding information. We demonstrate the validity of an analytical model for this regime that considers the effects of dark counts and dead time on the measured count rate. For the purpose of gaining a better understanding of these effects, the photon detections were separated from the dark counts via a software-induced gating mechanism. The model was verified by experimental data for mean photon numbers covering three orders of magnitude as well as for laser repetition frequencies below and above the inverse dead time. Consequently, our model would be of interest for predicting the detector response not only in the field of quantum communications, but also in any other quantum physics experiment where high detection rates are needed.
Single-photon-counting modules (SPCM's), with their high quantum efficiency, have been widely used to investigate effectively the photon statistics of various light sources, such as the single-photon state and emission light from controlled molecules, atoms, and quantum dots. However, such SPCM's cannot distinguish the arrivals of one photon and two (or more than two) photons at a moment, which makes measurement correction in real experiments. We analyze the effect of SPCM's on photon statistics based on the Hanbury-Brown-Twiss configuration when the total efficiency and background are considered, and it shows that the measured second-order degree of coherence and Mandel QQQ factor for different quantum states, including single-photon states and squeezed vacuum states, are corrected in different forms. A way of determining the squeezing of a squeezed vacuum state based on single-photon detection is presented.
With the growing use of online communications in our modern society, information security is becoming a big concern. Along with that, the progress in quantum computers is posing severe threats to such communications. Once powerful quantum computers are available, most of today's encryption schemes, which are based on computationally hard problems, will be broken within a short period. Researchers are therefore making a great effort to establish quantum-safe encryption schemes. One such scheme is quantum key distribution (QKD), which utilizes the laws of quantum mechanics. These cryptography protocols offer unconditional security to the communication between two distant parties by providing a secure way of sharing encryption keys between them. While over the last few decades QKD has continuously progressed, it is limited to a distance of up to several hundred kilometers using terrestrial quantum links. Satellites are therefore being considered to extend the QKD range for global coverage, although implementations of the satellite-based QKD infrastructure are still in their early stage. There are many aspects of QKD that need further assessment and advancement for establishing long-term satellite-based quantum communication (QC). My thesis works were focused on developing advanced systems for single-photon detectors and quantum sources. Single-photon avalanche diodes (SPADs) are the most viable option for satellite-based quantum communications. They must travel to outer space either for receiving quantum-states in the ground-to-satellite QC or for characterizing the quantum-sources in the satellite-to-ground QC. However, while in space, SPADs exhibit damage caused by the space radiation that gradually increases their dark counts. Performing QKD is not possible when the dark counts exceed a specific threshold. Hence, methods of reducing the detectors' dark counts by mitigating the damages would help to extend the SPADs' in-space useful lifetime. Laser annealing is one such effective method, found in lab experiments, to heal the radiation-induced detector damages. We now aim to carry out this method in low Earth orbit (LEO) to verify its in-orbit effectiveness. On that goal, we are building an annealing payload (APL) for a cube satellite (CubeSat) in collaboration with the University of Illinois at Urbana Champaign (UIUC). We, the University of Waterloo team, built one of the two segments of the APL-- a space-qualified detector module containing two Excelitas C30902SH and Excelitas SLiK detectors. Our miniaturized and compact module integrates the facilities required for the detector operation and laser annealing, as well as an active detector temperature control system. The operation of the detector module is highly flexible and software controllable. Our detector module will work together with the control board containing the laser annealing system (built by the UIUC team). Once the satellite has been launched in 2020, the in-orbit experiment will enable us to study the in-space SPAD radiation damage and their healing using the integrated annealing system. During a second project, we designed and built a new simple readout circuit for the negative feedback avalanche diodes (NFADs), which are free-running single-photon detectors at telecom wavelengths. These detectors suffer from strong afterpulsing effects, which limits their overall performances. Therefore, our readout system incorporates features to suppress NFAD afterpulses. We also used this custom readout to characterize two NFADs (from Princeton Lightwave) and assessed the performance of the new electronics. Our analysis showed that even at higher detection efficiencies, a 20 mu\\mumus hold-off time after each avalanche event is enough to extensively reduce the number of afterpulses and to keep the dark count rate below 100 Hz at 192 K temperature. Both the detectors showed timing jitter of less than 75 ps FWHM at their maximum efficiencies. The best figure of merit is found to be 1.6times107\\times 10^7times107, which is comparable to that of the high-performing superconducting nanowire single-photon detectors. This result demonstrates the suitability of our readout and the NFADs in various quantum optics applications, such as in long-distance quantum key distribution, where the detection rate is usually low. We then performed a blinding attack, which enables an Eavesdropper in QKD to gain information on the key, on these NFADs using bright illumination. These detectors are usually threshold detectors that generate a click when the optical power is above a certain threshold, otherwise they do not click. Blinding attack utilizes detectors' inability to resolve the photon numbers. During the experiment, we sent controlled optical pulses with a high time resolution to deterministically force detection at the detectors. The result demonstrated the NFADs' susceptibility to these attacks, which tells us to include countermeasures into the system to protect the communications. Finally, we built a quantum source to produce 785 nm polarized photons to implement decoy-state BB84 QKD. Our source utilized the sum-frequency generation scheme to generate 785 nm laser pulses. Its modulator system includes an intensity modulator and two-phase modulators in the Mach-Zehnder configuration to prepare polarized quantum states with different intensities. Our source provides a repetition rate of 500 MHz, which was successfully used in an airborne QKD demonstration with a moving receiver up to 10 km10~ km10 km distance. To summarize, my research projects are a contribution to the development of advanced devices, particularly single-photon detectors for quantum communications.
Single-photon detection concept is the most crucial and often difficult factor to determine the performance of quantum key distribution (QKD) systems. One solution to facilitate understanding this concept is to create a virtual environment for modeling, analyzing, and investigating the performance of single photon detectors. In this paper, a simulator for superconducting single photon detectors with time domain visualizer and configurable parameters is presented. The widely used ID281SNSPD in the QKD area was theoretically modeled in terms of pulse analysis, the impact of biasing current and the temperature on the dark counts rate and single photon-detection efficiency and influence of the number of photons per pulse on the single photon-detection efficiency. The simulated results were in good agreement with the theoretical results and the simulator demonstrated its adaptability.
Using correlated photon pairs produced via spontaneous parametric down-conversion, we have measured the absolute single-photon detection efficiencies and time responses of four detectors: two solid-state photomultipliers (SSPM's) manufactured by Rockwell International Corp., and two custom-modified single-photon counting modules (SSPM's) manufactured by EG, Canada. The highest observed efficiencies were 70.9\ifmmode\pm\else\textpm\fi{}1.9% (with an SSPM, at a wavelength of 632 nm) and 76.4\ifmmode\pm\else\textpm\fi{}2.3% (with an SPCM, at 702 nm). We believe these to be the highest reported single-photon detection efficiencies in the visible spectrum; they are important for quantum cryptography and loophole-free tests of Bell's inequalities, as well as more prosaic applications such as photon correlation spectroscopy and velocimetry. We found that the time profile for coincidences between the SSPM and the SPCM consisted of a main peak with a 3.5-ns full width at half maximum (FWHM) preceded by a smaller peak by 11 ns. A similar time profile between two SPCM's displayed only one peak, with a 300-ps FWHM. Afterpulses were detected in the SPCM's at a level of less than ${10}^{\mathrm{\ensuremath{-}}4}$ of the counting rate, with an exponential decay time constant of 4.5 \ensuremath{\mu}s.