Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE International Symposium on Inertial Sensors and Systems (INERTIAL)

Cross-Axis Coupling in an Atomic-Beam Interferometric Inertial Sensor

Yue Xin, Weichen Jia, Ke Shen, Shengzhe Wang, Qian-Lan Cai, Yan-Ying Feng

Published May 10, 2026• 0 citations
Publisher

Abstract

This paper investigates cross-axis coupling between rotation and acceleration measurements in a dual-beam atomic interferometric inertial sensor and presents an analytical decoupling method based on calibrated effective velocity parameters. In practical systems, mismatches in the effective velocity parameters of the two interferometers break the ideal orthogonality between the rotation and acceleration channels, causing each measured output to contain a residual contribution from the other inertial input. A phase model incorporating interferometer-specific effective velocity parameters is established to describe this mechanism and to derive the corresponding coupling terms. Independent rotation and acceleration calibrations are then performed to quantify the bidirectional coupling experimentally. The results show approximately linear cross-coupling, with coefficients of about 0.045 g/(°/s) for rotation-to-acceleration coupling and 0.196 (°/s)/g for acceleration-to-rotation coupling. Based on the calibrated parameters, an analytical reconstruction method is implemented to decouple the two channels. Experimental results show that the apparent coupling is effectively suppressed after correction, demonstrating the validity of the proposed model and method. These results identify cross-axis coupling as an intrinsic system-level error mechanism in simultaneous atomic rotation–acceleration sensing and provide a practical route toward more accurate and deployable multi-channel quantum inertial sensors.

DOI
10.1109/inertial69196.2026.11557936

Related papers

Closed-loop dual-channel atomic beam interferometry beyond the half-fringe limit

Anonymous, Yue Xin, Ke Shen +5 more

Atom interferometric inertial sensors offer exceptional sensitivity but are fundamentally constrained by the periodic phase response of matter-wave interference, which imposes an intrinsic half-fringe dynamic-range limit and prevents continuous inertial tracking. In multi-axis configurations, additional cross coupling between acceleration and rotation further complicates closed-loop operation. Here we demonstrate the first dual-channel closed-loop operation of an atomic beam interferometer, realizing decoupled feedback control of acceleration- and rotation-induced phases and overcoming the half-fringe limitation. Using continuous, transversely cooled $^{87}$Rb atomic beams, the interferometric phases associated with rotation and acceleration are independently extracted, tracked across multiple fringes, and actively compensated through Raman frequency modulation. This closed-loop scheme enables unambiguous measurements up to $\pm1\,\mathrm{^{\circ}/s}$ in rotation and $\pm0.17\,\mathrm{g}$ in acceleration while maintaining high fringe contrast, corresponding to nearly two orders-of-magnitude extension beyond the conventional half-fringe limit. The sensor achieves a long-term stability of $4\times10^{-4}\,\mathrm{^{\circ}/h}$ for rotation and $4\,\mathrm{μg}$ for acceleration at an averaging time of $1000\,\mathrm{s}$. By converting the intrinsically periodic interferometric response into stabilized phase-encoded inertial channels, this work establishes a new operating regime for atomic beam interferometry and advances matter-wave sensors toward practical quantum inertial navigation under dynamic conditions.

arXiv:2603.14777•Physical Review Applied•Jul 21, 2026•1 citation

A Continuous Dual-Axis Atomic Interferometric Inertial Sensor

Peiqiang Yan, Weichen Jia, Ke Shen +2 more

We present an interferometric inertial sensor that utilizes two counter-propagating atomic beams with transverse two-dimensional cooling. By employing three parallel and spatially aligned Raman laser beams for Doppler-sensitive Raman transitions, we successfully generate inertia-sensitive Mach-Zehnder interference fringes with an interrogation length of 2L = 54 cm. The sensor’s capability to measure rotation and acceleration simultaneously in dynamic environments is validated through comparative analysis with classical sensors under force oscillation in different directions. Additionally, we conduct experiments on a turntable to calibrate the gyroscope’s scaling factor and address nonlinearity. The angular random walk (ARW) and velocity random walk (VRW) of the sensor are 3×10−4 °/√h and 107 μg/√Hz, respectively, with the long-term stability reaching 9 × 10−4 °/h for rotation and 10 μg for acceleration at an integration time of 1000 s.

arXiv:2311.16557•IEEE Transactions on Instrumentation and Measurement•Jan 1, 2025•7 citations

Digital closed-loop thermal atomic beam interferometer for high-bandwidth, wide-dynamic-range, and simultaneous absolute sensing of acceleration and rotation

Tomoya Sato, Toshiyuki Hosoya, Martin Miranda +3 more

We present a theoretical proposal and simulation study of a digital closed-loop thermal atomic-beam interferometer for inertial navigation applications. The scheme synchronizes phase biasing with momentum-kick reversal through the atomic transit time, extracting four interferometric phases to suppress Raman beam path-length errors, while two-photon detuning feedback maintains a pseudo-inertial frame and eliminates cross-coupling. The interferometer enables simultaneous measurements of acceleration and rotation based on an absolute, atom-interferometric reference, with high bandwidth and a wide dynamic range. Numerical simulations verify that acceleration and angular velocity can be measured simultaneously and independently in real time without cross-coupling, demonstrating the absolute, decoupled nature of the proposed measurement scheme. We further evaluate the noise-limited performance of the sensor and obtain sensitivities of $3{\rm μm / s^2 / \sqrt{Hz}}$ (velocity random walk) and $15{\rm μdeg / \sqrt{h}}$ (angular random walk) for a ${170}^{\circ}$ $^{85}$Rb beam and an interferometer arm length of 100~mm, surpassing the performance of sensors currently used in state-of-the-art inertial navigation systems.

arXiv:2509.05942•Physical Review Applied•Jan 22, 2026•0 citations

Multi-Axis Inertial Sensing with 2D Matter-Wave Arrays

Knut Stolzenberg, Christian Struckmann, Sebastian Bode +8 more

Atom interferometery is an exquisite measurement technique sensitive to inertial forces. However, it is commonly limited to a single sensitive axis, allowing high-precision multidimensional sensing only through subsequent or postcorrected measurements. We report on a novel method for multi-axis inertial sensing based on the correlation of simultaneous light-pulse atom interferometers in 2D array arrangements of Bose-Einstein condensates (BEC). Deploying a scalable 3×3 BEC array spanning 1.6 mm^{2} created using time-averaged optical potentials, we perform measurements of linear acceleration induced by gravity and simultaneously demonstrate sensitivity to angular velocity and acceleration of a rotating reference mirror, as well as gravity gradients and higher-order derivatives. Our Letter enables simple, high-precision multi-axis inertial sensing compatible with high rotation rates, e.g., for inertial navigation in dynamic environments. We finally envision further applications of our method, e.g., 3D in situ measurements and reconstruction of laser beam intensities and wave fronts.

arXiv:2403.08762•Physical Review Letters•Apr 9, 2025•16 citations

Closed-loop dual-atom-interferometer inertial sensor with continuous cold atomic beams

Zhi-Xin Meng, Pei-Qiang Yan, Shengzhe Wang +3 more

We demonstrate a closed-loop light-pulse atom-interferometer inertial sensor that can realize continuous decoupled measurements of acceleration and rotation rate. The sensor operates with double-loop atom interferometers, which share the same Raman light pulses in a spatially separated Mach-Zehnder configuration and use continuous cold atomic beams propagating in opposite directions from two ${\text{2D}}^{+}$ magneto-optical trappings. Acceleration and the rotation rate are decoupled and simultaneously measured by the sum and difference of dual-atom-interferometer signals, respectively. The sensitivities of inertial measurements are also increased to be approximately 1.86 times higher than that of a single atom interferometer. The acceleration phase shift is compensated in real time by phase locking these interferometers via the Raman laser phases from the sum-interferometer signal, and the gyroscope performance is improved. We achieve long-term stabilities of $6.1\phantom{\rule{0.2em}{0ex}}\text{\ensuremath{\mu}}\text{g}$ and 840 nrad/s for the acceleration and the rotation rate, respectively, using a short interrogation time of 0.87 ms (interference area $A=0.097\phantom{\rule{0.2em}{0ex}}{\text{mm}}^{2}$). This work provides a building block for an atomic interferometer-based inertial measurement unit for use in field applications that require a high data rate and high stability.

arXiv:2210.15346•Physical Review Applied•Mar 22, 2024•23 citations

A New Method for Six-axis Inertial Measurement Using Cold Atom Interferomenter

Tijing Cai

In order to monitor 3 axes rotation and acceleration of vehicle simultaneously,a realization scheme for measuring 6 axes inertial parameters using cold atom interferometry was presented.Through exerting different types and directions Raman pulses on two counterpropagating atomic beams in spatial domain,it achieved beams splitting of cold atom,and multiple sub-interferometers with effective interference plane point to several orientations.The relation between interferometry phase shift and the corresponding inertial parameter was derived,and the measurement principle of each axis rotation and acceleration was deduced through interferometry phase shift.The measurement of x axis acceleration by extending pulse with 45° to x axis and y axis was presented based on 5 axes inertial parameters.By analysing the beam splitting,construction and measurement of the interferometer,it showed this scheme has access to 3 axes of rotation and acceleration.

Piezoelectrics and Acoustooptics•Jan 1, 2009•0 citations
This paper investigates cross-axis coupling between rotation and acceleration measurements in a dual-beam atomic interferometric inertial sensor and presents an analytical decoupling method based on calibrated effective velocity parameters. In practical systems, mismatches in the effective velocity parameters of the two interferometers break the ideal orthogonality between the rotation and acceleration channels, causing each measured output to contain a residual contribution from the other inertial input. A phase model incorporating interferometer-specific effective velocity parameters is established to describe this mechanism and to derive the corresponding coupling terms. Independent rotation and acceleration calibrations are then performed to quantify the bidirectional coupling experimentally. The results show approximately linear cross-coupling, with coefficients of about 0.045 g/(°/s) for rotation-to-acceleration coupling and 0.196 (°/s)/g for acceleration-to-rotation coupling. Based on the calibrated parameters, an analytical reconstruction method is implemented to decouple the two channels. Experimental results show that the apparent coupling is effectively suppressed after correction, demonstrating the validity of the proposed model and method. These results identify cross-axis coupling as an intrinsic system-level error mechanism in simultaneous atomic rotation–acceleration sensing and provide a practical route toward more accurate and deployable multi-channel quantum inertial sensors.
Atom interferometric inertial sensors offer exceptional sensitivity but are fundamentally constrained by the periodic phase response of matter-wave interference, which imposes an intrinsic half-fringe dynamic-range limit and prevents continuous inertial tracking. In multi-axis configurations, additional cross coupling between acceleration and rotation further complicates closed-loop operation. Here we demonstrate the first dual-channel closed-loop operation of an atomic beam interferometer, realizing decoupled feedback control of acceleration- and rotation-induced phases and overcoming the half-fringe limitation. Using continuous, transversely cooled 87^{87}87Rb atomic beams, the interferometric phases associated with rotation and acceleration are independently extracted, tracked across multiple fringes, and actively compensated through Raman frequency modulation. This closed-loop scheme enables unambiguous measurements up to ±1 ∘/s\pm1\,\mathrm{^{\circ}/s}±1∘/s in rotation and ±0.17 g\pm0.17\,\mathrm{g}±0.17g in acceleration while maintaining high fringe contrast, corresponding to nearly two orders-of-magnitude extension beyond the conventional half-fringe limit. The sensor achieves a long-term stability of 4×10−4 ∘/h4\times10^{-4}\,\mathrm{^{\circ}/h}4×10−4∘/h for rotation and 4 μg4\,\mathrm{μg}4μg for acceleration at an averaging time of 1000 s1000\,\mathrm{s}1000s. By converting the intrinsically periodic interferometric response into stabilized phase-encoded inertial channels, this work establishes a new operating regime for atomic beam interferometry and advances matter-wave sensors toward practical quantum inertial navigation under dynamic conditions.
We present an interferometric inertial sensor that utilizes two counter-propagating atomic beams with transverse two-dimensional cooling. By employing three parallel and spatially aligned Raman laser beams for Doppler-sensitive Raman transitions, we successfully generate inertia-sensitive Mach-Zehnder interference fringes with an interrogation length of 2L = 54 cm. The sensor’s capability to measure rotation and acceleration simultaneously in dynamic environments is validated through comparative analysis with classical sensors under force oscillation in different directions. Additionally, we conduct experiments on a turntable to calibrate the gyroscope’s scaling factor and address nonlinearity. The angular random walk (ARW) and velocity random walk (VRW) of the sensor are 3×10−4 °/√h and 107 μg/√Hz, respectively, with the long-term stability reaching 9 × 10−4 °/h for rotation and 10 μg for acceleration at an integration time of 1000 s.
We present a theoretical proposal and simulation study of a digital closed-loop thermal atomic-beam interferometer for inertial navigation applications. The scheme synchronizes phase biasing with momentum-kick reversal through the atomic transit time, extracting four interferometric phases to suppress Raman beam path-length errors, while two-photon detuning feedback maintains a pseudo-inertial frame and eliminates cross-coupling. The interferometer enables simultaneous measurements of acceleration and rotation based on an absolute, atom-interferometric reference, with high bandwidth and a wide dynamic range. Numerical simulations verify that acceleration and angular velocity can be measured simultaneously and independently in real time without cross-coupling, demonstrating the absolute, decoupled nature of the proposed measurement scheme. We further evaluate the noise-limited performance of the sensor and obtain sensitivities of 3μm/s2/Hz3{\rm μm / s^2 / \sqrt{Hz}}3μm/s2/Hz​ (velocity random walk) and 15μdeg/h15{\rm μdeg / \sqrt{h}}15μdeg/h​ (angular random walk) for a 170∘{170}^{\circ}170∘ 85^{85}85Rb beam and an interferometer arm length of 100~mm, surpassing the performance of sensors currently used in state-of-the-art inertial navigation systems.
Atom interferometery is an exquisite measurement technique sensitive to inertial forces. However, it is commonly limited to a single sensitive axis, allowing high-precision multidimensional sensing only through subsequent or postcorrected measurements. We report on a novel method for multi-axis inertial sensing based on the correlation of simultaneous light-pulse atom interferometers in 2D array arrangements of Bose-Einstein condensates (BEC). Deploying a scalable 3×3 BEC array spanning 1.6 mm^{2} created using time-averaged optical potentials, we perform measurements of linear acceleration induced by gravity and simultaneously demonstrate sensitivity to angular velocity and acceleration of a rotating reference mirror, as well as gravity gradients and higher-order derivatives. Our Letter enables simple, high-precision multi-axis inertial sensing compatible with high rotation rates, e.g., for inertial navigation in dynamic environments. We finally envision further applications of our method, e.g., 3D in situ measurements and reconstruction of laser beam intensities and wave fronts.
We demonstrate a closed-loop light-pulse atom-interferometer inertial sensor that can realize continuous decoupled measurements of acceleration and rotation rate. The sensor operates with double-loop atom interferometers, which share the same Raman light pulses in a spatially separated Mach-Zehnder configuration and use continuous cold atomic beams propagating in opposite directions from two 2D+{\text{2D}}^{+}2D+ magneto-optical trappings. Acceleration and the rotation rate are decoupled and simultaneously measured by the sum and difference of dual-atom-interferometer signals, respectively. The sensitivities of inertial measurements are also increased to be approximately 1.86 times higher than that of a single atom interferometer. The acceleration phase shift is compensated in real time by phase locking these interferometers via the Raman laser phases from the sum-interferometer signal, and the gyroscope performance is improved. We achieve long-term stabilities of $6.1\phantom{\rule{0.2em}{0ex}}\text{\ensuremath{\mu}}\text{g}$ and 840 nrad/s for the acceleration and the rotation rate, respectively, using a short interrogation time of 0.87 ms (interference area A=0.097mm2A=0.097\phantom{\rule{0.2em}{0ex}}{\text{mm}}^{2}A=0.097mm2). This work provides a building block for an atomic interferometer-based inertial measurement unit for use in field applications that require a high data rate and high stability.
In order to monitor 3 axes rotation and acceleration of vehicle simultaneously,a realization scheme for measuring 6 axes inertial parameters using cold atom interferometry was presented.Through exerting different types and directions Raman pulses on two counterpropagating atomic beams in spatial domain,it achieved beams splitting of cold atom,and multiple sub-interferometers with effective interference plane point to several orientations.The relation between interferometry phase shift and the corresponding inertial parameter was derived,and the measurement principle of each axis rotation and acceleration was deduced through interferometry phase shift.The measurement of x axis acceleration by extending pulse with 45° to x axis and y axis was presented based on 5 axes inertial parameters.By analysing the beam splitting,construction and measurement of the interferometer,it showed this scheme has access to 3 axes of rotation and acceleration.