Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Effect of Eccosorb IR Filters on Qubit Coherence

Taryn V. Stefanski, Lukas Johannes Splitthoff, S. K. Singh, Figen YILMAZ, Martijn F. S. Zwanenburg, Christian Kraglund Andersen

Published Jan 1, 2023• 0 citations
OpenAlex

Abstract

Superconducting qubits may suffer, despite extensive shielding, from interactions with residual noise photons arriving through signal lines to the device, which leads to qubit decoherence. To mitigate the photon population at the qubit frequency due to thermal radiation, attenuators can thermalize the electromagnetic environment at the sample stage. However, to prevent quasiparticle poisoning caused by Cooper pair breaking due to IR radiation, additional filtering is required. Such IR filters are routinely achieved using Eccosorb, a commercially available castable dielectric. We manufacture Eccosorb filters of various length and grade and characterize them at room and liquid nitrogen temperatures up to 67 GHz. Based on the obtained frequency dependent attenuation, we compute the residual noise photon population at base temperature and conclude on the preferred filter and attenuator configuration for superconducting qubit experiments. We validate the suggested microwave filtering for drive and flux bias lines by comparing coherent properties of transmon qubits for different filter configurations.

Related papers

Magnetically loaded dielectric based absorptive filters and attenuators with tunable attenuation for superconducting quantum circuits

Srijita Das, Madhavi Chand, Samuel John +4 more

Cryogenic filtering and attenuation play a crucial role in the control and readout of superconducting qubits, ensuring that unwanted noise does not degrade qubit coherence. These devices typically operate in the microwave C band (4–8 GHz) and use attenuators (input) and circulators/isolators (output) to control in-band noise, while reflective filters are used to reject out-of-band noise. However, these devices tend to become transparent to terahertz and infrared radiation. Such high-frequency radiation reaching the qubit destroys superconductivity and induces dissipation, degrading the coherence properties of these devices. Magnetically loaded epoxy (like Eccosorb \(^\mathrm{{TM}}\) ) has been widely used as a dielectric to construct filters that absorb high-frequency radiation while minimizing loss in the operating band. Here, we demonstrate the construction and characterization of absorptive filters with variable in-band attenuation by combining Eccosorb \(^\mathrm{{TM}}\) or iron powder mixed with Stycast in different ratios. We show that such filters can be made with sufficiently large in-band attenuation to replace the usual thin-film resistor-based attenuators and simplify cryogenic wiring by combining attenuation and IR filtering in a single device. We characterize the microwave performance at room temperature and at dilution fridge temperatures for devices with insertion losses ranging from 1 dB to 20 dB at 7 GHz. In a separate set of experiments, we also test the materials’ absorption capabilities at terahertz frequencies up to 450 GHz. Finally, we demonstrate high coherence in a 3D superconducting qubit ( \(T_1, T_2^E \approx 100~\mu s\) ) using these filters and attenuators, thereby confirming their efficacy.

Scientific Reports•Jul 31, 2026•0 citations

Engineering the microwave to infrared noise photon flux for superconducting quantum systems

Sergey Danilin, João Barbosa, Michael Farage +6 more

Electromagnetic filtering is essential for the coherent control, operation and readout of superconducting quantum circuits at milliKelvin temperatures. The suppression of spurious modes around transition frequencies of a few GHz is well understood and mainly achieved by on-chip and package considerations. Noise photons of higher frequencies - beyond the pair-breaking energies - cause decoherence and require spectral engineering before reaching the packaged quantum chip. The external wires that pass into the refrigerator and go down to the quantum circuit provide a direct path for these photons. This article contains quantitative analysis and experimental data for the noise photon flux through coaxial, filtered wiring. The attenuation of the coaxial cable at room temperature and the noise photon flux estimates for typical wiring configurations are provided. Compact cryogenic microwave low-pass filters with CR-110 and Esorb-230 absorptive dielectric fillings are presented along with experimental data at room and cryogenic temperatures up to 70 GHz. Filter cut-off frequencies between 1 to 10 GHz are set by the filter length, and the roll-off is material dependent. The relative dielectric permittivity and magnetic permeability for the Esorb-230 material in the pair-breaking frequency range of 75 to 110 GHz are measured, and the filter properties in this frequency range are calculated. The estimated dramatic suppression of the noise photon flux due to the filter proves its usefulness for experiments with superconducting quantum systems.

arXiv:2107.09331•EPJ Quantum Technology•Jan 15, 2022•29 citations

Characterization of Transmission Properties of Infrared Filters and Attenuators Up to 125 GHz

Junta Igarashi, Kosuke Mizuno, Ryo Ito +6 more

Recent advancements in quantum technology have driven a growing demand for microwave components capable of operating at cryogenic temperatures. Filtering frequencies above 80 GHz, corresponding to the superconducting gap in aluminum, is particularly important for superconducting qubits. Nevertheless, due to experimental difficulties, such evaluations have rarely been conducted, even at room temperature (RT). In this study, as an initial step, we characterize transmission properties of infrared (IR) filters and attenuators commonly used in low-temperature measurement setups at high frequencies up to 125 GHz at RT. This study offers insight into microwave components employed in quantum computing within the 100 GHz band.

IEEE International Symposium on Radio-Frequency Integration Technology (RFIT)•Aug 25, 2025•0 citations

Suppression of Quasiparticle Poisoning to $10^{-11}$ Levels in Superconducting Qubits via Infrared Shielding

Wei-En Lin, Chen-Hsun Ma, Erh-Hsiang Yeh +7 more

Quasiparticle poisoning bottlenecks superconducting qubits, limiting coherence and the scalability of quantum processors. In this work, we systematically investigate quasiparticle poisoning in superconducting qubits under three infrared (IR) shielding configurations, ranging from a dedicated multi-layer design to a simplified implementation. By measuring quasiparticle-induced parity switching, we demonstrate a suppression of the switching rate by over four orders of magnitude via the implementation of improved shielding. In the best configuration, the rate decreases over time following cooldown and reaches 0.069$\,$Hz on day 34, corresponding to an anticipated quasiparticle density per Cooper pair of $1.88\times10^{-11}$. To our knowledge, this represents the lowest quasiparticle density reported in the literature to date. The remaining quasiparticle population is likely dominated by sporadic phonon bursts stemming from mechanical stress release in the on-chip films, as well as from the surrounding environment. The effective qubit temperature follows the phonon bath down to 17$\,$mK, enabling initialization errors of $\sim 0.01\%$ for 3$\,$GHz qubits. These results demonstrate that proper IR shielding and thermalization are essential for suppressing quasiparticle poisoning and enabling high-coherence, scalable superconducting qubit systems.

quant-pharXiv:2606.07339•Jun 8, 2026•0 citations

Cavity Attenuators for Superconducting Qubits

Zhixin Wang, Shyam Shankar, Zlatko Minev +3 more

Improving qubit coherence times is fundamental to the development of quantum computing technology. In most experiments in circuit quantum electrodynamics, dephasing induced by residual thermal photons in the readout resonator limits the coherence times of superconducting qubits. The authors design and test a type of microwave cavity attenuator that can be well thermalized to the base stage of a dilution refrigerator. With these cavity attenuators, they reproducibly measure enhanced qubit coherence times and report very low thermal-photon populations in the readout mode. This invention is a useful addition to the toolbox for state-of-the-art quantum circuitry.

arXiv:1807.04849•Physical Review Applied•Jan 16, 2019•112 citations

Microstrip filters for measurement and control of superconducting qubits

Luigi Longobardi, D. A. Bennett, Vijay Patel +2 more

Careful filtering is necessary for observations of quantum phenomena in superconducting circuits at low temperatures. Measurements of coherence between quantum states require extensive filtering to protect against noise coupled from room temperature electronics. We demonstrate distributed transmission line filters which cut off exponentially at GHz frequencies and can be anchored at the base temperature of a dilution refrigerator. The compact design makes them suitable to filter many different bias lines in the same setup, necessary for the control and measurement of superconducting qubits.

arXiv:1301.3153•Review of Scientific Instruments•Jan 1, 2013•13 citations
Superconducting qubits may suffer, despite extensive shielding, from interactions with residual noise photons arriving through signal lines to the device, which leads to qubit decoherence. To mitigate the photon population at the qubit frequency due to thermal radiation, attenuators can thermalize the electromagnetic environment at the sample stage. However, to prevent quasiparticle poisoning caused by Cooper pair breaking due to IR radiation, additional filtering is required. Such IR filters are routinely achieved using Eccosorb, a commercially available castable dielectric. We manufacture Eccosorb filters of various length and grade and characterize them at room and liquid nitrogen temperatures up to 67 GHz. Based on the obtained frequency dependent attenuation, we compute the residual noise photon population at base temperature and conclude on the preferred filter and attenuator configuration for superconducting qubit experiments. We validate the suggested microwave filtering for drive and flux bias lines by comparing coherent properties of transmon qubits for different filter configurations.
Cryogenic filtering and attenuation play a crucial role in the control and readout of superconducting qubits, ensuring that unwanted noise does not degrade qubit coherence. These devices typically operate in the microwave C band (4–8 GHz) and use attenuators (input) and circulators/isolators (output) to control in-band noise, while reflective filters are used to reject out-of-band noise. However, these devices tend to become transparent to terahertz and infrared radiation. Such high-frequency radiation reaching the qubit destroys superconductivity and induces dissipation, degrading the coherence properties of these devices. Magnetically loaded epoxy (like Eccosorb TM^\mathrm{{TM}}TM ) has been widely used as a dielectric to construct filters that absorb high-frequency radiation while minimizing loss in the operating band. Here, we demonstrate the construction and characterization of absorptive filters with variable in-band attenuation by combining Eccosorb TM^\mathrm{{TM}}TM or iron powder mixed with Stycast in different ratios. We show that such filters can be made with sufficiently large in-band attenuation to replace the usual thin-film resistor-based attenuators and simplify cryogenic wiring by combining attenuation and IR filtering in a single device. We characterize the microwave performance at room temperature and at dilution fridge temperatures for devices with insertion losses ranging from 1 dB to 20 dB at 7 GHz. In a separate set of experiments, we also test the materials’ absorption capabilities at terahertz frequencies up to 450 GHz. Finally, we demonstrate high coherence in a 3D superconducting qubit ( T1,T2E≈100 μsT_1, T_2^E \approx 100~\mu sT1​,T2E​≈100 μs ) using these filters and attenuators, thereby confirming their efficacy.
Electromagnetic filtering is essential for the coherent control, operation and readout of superconducting quantum circuits at milliKelvin temperatures. The suppression of spurious modes around transition frequencies of a few GHz is well understood and mainly achieved by on-chip and package considerations. Noise photons of higher frequencies - beyond the pair-breaking energies - cause decoherence and require spectral engineering before reaching the packaged quantum chip. The external wires that pass into the refrigerator and go down to the quantum circuit provide a direct path for these photons. This article contains quantitative analysis and experimental data for the noise photon flux through coaxial, filtered wiring. The attenuation of the coaxial cable at room temperature and the noise photon flux estimates for typical wiring configurations are provided. Compact cryogenic microwave low-pass filters with CR-110 and Esorb-230 absorptive dielectric fillings are presented along with experimental data at room and cryogenic temperatures up to 70 GHz. Filter cut-off frequencies between 1 to 10 GHz are set by the filter length, and the roll-off is material dependent. The relative dielectric permittivity and magnetic permeability for the Esorb-230 material in the pair-breaking frequency range of 75 to 110 GHz are measured, and the filter properties in this frequency range are calculated. The estimated dramatic suppression of the noise photon flux due to the filter proves its usefulness for experiments with superconducting quantum systems.
Recent advancements in quantum technology have driven a growing demand for microwave components capable of operating at cryogenic temperatures. Filtering frequencies above 80 GHz, corresponding to the superconducting gap in aluminum, is particularly important for superconducting qubits. Nevertheless, due to experimental difficulties, such evaluations have rarely been conducted, even at room temperature (RT). In this study, as an initial step, we characterize transmission properties of infrared (IR) filters and attenuators commonly used in low-temperature measurement setups at high frequencies up to 125 GHz at RT. This study offers insight into microwave components employed in quantum computing within the 100 GHz band.
Suppression of Quasiparticle Poisoning to 10−1110^{-11}10−11 Levels in Superconducting Qubits via Infrared Shielding
Quasiparticle poisoning bottlenecks superconducting qubits, limiting coherence and the scalability of quantum processors. In this work, we systematically investigate quasiparticle poisoning in superconducting qubits under three infrared (IR) shielding configurations, ranging from a dedicated multi-layer design to a simplified implementation. By measuring quasiparticle-induced parity switching, we demonstrate a suppression of the switching rate by over four orders of magnitude via the implementation of improved shielding. In the best configuration, the rate decreases over time following cooldown and reaches 0.069 \,Hz on day 34, corresponding to an anticipated quasiparticle density per Cooper pair of 1.88×10−111.88\times10^{-11}1.88×10−11. To our knowledge, this represents the lowest quasiparticle density reported in the literature to date. The remaining quasiparticle population is likely dominated by sporadic phonon bursts stemming from mechanical stress release in the on-chip films, as well as from the surrounding environment. The effective qubit temperature follows the phonon bath down to 17 \,mK, enabling initialization errors of ∼0.01%\sim 0.01\%∼0.01% for 3 \,GHz qubits. These results demonstrate that proper IR shielding and thermalization are essential for suppressing quasiparticle poisoning and enabling high-coherence, scalable superconducting qubit systems.
Improving qubit coherence times is fundamental to the development of quantum computing technology. In most experiments in circuit quantum electrodynamics, dephasing induced by residual thermal photons in the readout resonator limits the coherence times of superconducting qubits. The authors design and test a type of microwave cavity attenuator that can be well thermalized to the base stage of a dilution refrigerator. With these cavity attenuators, they reproducibly measure enhanced qubit coherence times and report very low thermal-photon populations in the readout mode. This invention is a useful addition to the toolbox for state-of-the-art quantum circuitry.
Careful filtering is necessary for observations of quantum phenomena in superconducting circuits at low temperatures. Measurements of coherence between quantum states require extensive filtering to protect against noise coupled from room temperature electronics. We demonstrate distributed transmission line filters which cut off exponentially at GHz frequencies and can be anchored at the base temperature of a dilution refrigerator. The compact design makes them suitable to filter many different bias lines in the same setup, necessary for the control and measurement of superconducting qubits.