Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Optics

Optimization of polarization spectroscopy signal for laser-frequency stabilization

Rajni Bala, Joyee Ghosh, Vivek Venkataraman

Published Aug 29, 2024• 0 citations
Publisher

Abstract

Abstract We experimentally generate polarization spectroscopy (error) signals corresponding to the D2-line hyperfine transitions, F g = 2 → F e = 1 , 2 , 3 of 87Rb, and F g = 3 → F e = 2 , 3 , 4 of 85Rb, and show that the strongest error signals correspond to the closed hyperfine transitions (oscillator strength ∼ 0.7 ), F g = 2 → F e = 3 and F g = 3 → F e = 4 , respectively. We make the generated error signal robust to fluctuations in external parameters by finding optimum values for the vapor cell temperature and pump-probe intensities at two different beam diameters. We further employ these optimized error signals to directly (without the need for frequency/phase modulation) lock the laser frequency—reducing the rms drift/linewidth from ∼ 10 MHz to < 500 kHz, when measured over a ∼ 60 min duration. In addition, by comparing theoretically calculated and experimentally measured error signals for the pump intensities ranging from ∼ 0.1 I sat 0 − 10 I sat 0 (where, I sat 0 ∼ 1.6 mW cm−2 is the two-level saturation intensity for the Rb D2-line transitions), we discuss the applicability and limitations of existing numerical and analytical approaches based on a full multi-level rate equation model for polarization spectroscopy.

DOI
10.1088/2040-8986/ad7516

Related papers

Theoretical and Experimental Study of Optimization of Polarization Spectroscopy for the D2 Closed Transition Line of 87Rb Atoms

Jeongyoun Jeong, Sanglok Lee, Sungi Hwang +3 more

We experimentally and theoretically investigated the optimal condition of polarization spectroscopy for frequency stabilization on various pump beam intensities and vapor cell temperatures for the D2 closed transition line of 87Rb atoms. We compared the experimental results, such as the amplitude, width, and slope, of the polarization spectroscopy signal with the theoretical results obtained from the numerical calculation of temporal density matrix equations. Based on the results, we found the optimal parameters, such as the pump beam intensity and vapor cell temperature, for polarization spectroscopy. The theoretically expected optimal parameters were, qualitatively, in good agreement with the experimental results.

Applied Sciences•Aug 5, 2021•5 citations

Optimization of error signal lineshape for modulation-free robust laser frequency stabilization

Poonam Yadav, Arnab Ghosh, Neha Singh +4 more

Abstract Frequency-stabilized external cavity diode lasers are essential components of precision quantum experiments. Atomic hyperfine states involved in such experiments are very sensitive to laser frequency drifts and thus the accuracy of the results is directly linked to the stability of the laser source. The quality of the error signal determines the lock performance of the laser source. An optimum error signal provides protection against mechanical vibration, laser intensity noise, and ambient magnetic field fluctuations. We have discussed the optimization of the error signal shape profile for 133Cs D2 line, 62 S 1/2 F = 4 to 62 P 3/2 F’ = 4/5 crossover transition. For a non-optimum value, the peak-to-peak frequency drift is ∼ 8 MHz with the FWHM of the drift being 2.72 ± 0.3 MHz, whereas the FWHM for an optimized value is 436 ± 73 kHz showing a 6 times reduction. Also, the peak-to-peak frequency drift lies within 1.1 MHz measured for over 25 minutes which makes it suitable for use in high-precision spectroscopy and quantum experiments. Moreover, the optical layout allows possibility of further miniaturization which is quite crucial for field applications and deployable quantum sensors.

Physica Scripta•Mar 11, 2025•2 citations

Polarization spectroscopy of a closed atomic transition: applications to laser frequency locking

C P Pearman, Charles S. Adams, Simon G. Cox +3 more

We study polarization spectroscopy of Rb vapour. A weak probe beam analyses the birefringence induced in a room temperature vapour by a strong counterpropagating circularly polarized pump beam. In contrast to most other work on polarization spectroscopy, we use a polarization beam splitting cube and two detectors (rather than a polarizer and one detector) to analyse the probe beam. The signal is in the form of a derivative of a Lorentzian. For theoretical analysis we study the closed atomic transition 5 2 S 1/2 ( F = 3) → 5 2 P 3/2 ( F ' = 4) in the D2 line of 85 Rb. We study the time needed to redistribute population among the m F states, derive an expression for the expected lineshape and present experimental data in excellent agreement with theory. The polarization spectrum provides an ideal error signal for frequency stabilization of a laser. We describe the geometry and parameters for optimizing the error signal.

Journal of Physics B Atomic Molecular and Optical Physics•Dec 4, 2002•229 citations

Laser Stabilization via Saturation Absorption Spectroscopy

Mehmet Hüseyin Sevim, Kamil Çınar, Murat Salim Karabinaoğlu +3 more

Precise laser stabilization is a fundamental aspect of modern metrology, directly influencing the accuracy of fundamental measurements in fields such as high-precision metrology, atomic sensor applications, and quantum technologies. Saturation absorption spectroscopy (SAS) is one of the most effective techniques for achieving high spectral stability, as it enables laser frequencies to be locked to atomic resonances. This technique exploits the nonlinear interaction between a weaker probe beam and a stronger pump beam within a rubidium (Rb) atomic vapor cell. By eliminating Doppler broadening, SAS allows well-defined hyperfine transitions to be resolved, providing a reliable optical frequency reference. This study aims to optimize laser frequency stabilization using the SAS technique by investigating the effects of laser light polarization, atomic vapor cell temperature, and pump-probe power adjustments. Polarization-dependent selection rules influence transition probabilities, thereby affecting spectral contrast and frequency stability. Additionally, atomic density variations, which depend on the vapor cell temperature, influence signal strength and linewidth, necessitating precise temperature control for optimal performance. Furthermore, the pump power must be sufficient to induce saturation without excessive power broadening, while the probe power must remain low enough to prevent spectral line distortion. By optimizing polarization, temperature, and power parameters, the stabilization of the Rb atomic laser can be enhanced, leading to improved reproducibility and consistency in high-precision measurements. SAS-based laser stabilization is particularly crucial for atomic sensor applications and quantum technologies, where highly stable, narrow-linewidth lasers are essential for precision measurements. Applications such as atomic magnetometers, gyroscopes, and inertial navigation systems depend on precisely stabilized lasers for optimal performance. By enhancing the reliability of laser frequency stabilization, this work contributes to the advancement of next-generation atomic sensors with improved sensitivity and stability.

•Jan 1, 2025•0 citations

Frequency Modulation Spectroscopy and Modulation Transfer Spectroscopy for Laser Stabilization to Rubidium Atomic Resonances

Jinni Wu, Ningxuan Zheng, Wenhui Li

We make a detailed comparison of frequency modulation spectroscopy (FMS) and modulation transfer spectroscopy (MTS) and of their applications in stabilizing laser frequency. In both FMS and MTS, intensity modulations of probe beam are observed in saturated absorption spectroscopy of 87Rb atoms. However, the two modulation profiles appear different due to their distinct origins. Demodulation gives rise to frequency discrimination spectra, which can serve as error signals for frequency locking. The optimal error signal of FMS has a larger linear slope but also a slanted baseline, in contrast to that of MTS. We apply FMS and MTS to stabilize two 780 nm external cavity diode lasers to D2 lines of 87Rb atoms. We measure laser linewidth and stability using beat notes of two independently locked lasers. A laser linewidth as narrow as 12.9 kHz is achieved in FMS locking, compared to 70.8 kHz in MTS locking. A laser stability at the level of 10−12 is reached in both schemes. Nevertheless, FMS locking offers a better short-term stability, whereas MTS locking yields a smaller long-term drift. Our investigation of FMS and MTS would be valuable for making a choice of these spectroscopy techniques for laser stabilization as well as other relevant applications.

Photonics•Oct 21, 2026•0 citations

Polarization anisotropy in absorption enhanced modulation transfer spectroscopy and laser locking for Rb D 1 line

Wen-Lei Zhao, Xinxiu Zhou, Wenxiang Xie +2 more

In a spin-exchange relaxation-free (SERF) atomic magnetometer, the pump and probe laser frequencies are tuned to the D 1 transition line of alkali metal atoms to enhance measurement sensitivity. The D 1 line, a non-cycling transition, exhibits a low absorption coefficient. This study theoretically analyzes the influence of different parameters on the absorption coefficient of the D 1 line and proposes a polarization-dependent approach to enhance it. A frequency stabilization method based on modulation transfer spectroscopy (MTS) with an enhanced absorption coefficient is introduced. Compared with the conventional method, optimizing the probe beam’s polarization increases the absorption coefficient, raising the amplitude of the MTS signal. The results show that using a stronger MTS signal for frequency stabilization reduces the laser's frequency noise. Using heterodyne measurement, we characterize the linewidth-narrowing effect of MTS locking and evaluate the frequency stability of the locked laser. The linewidth of each laser is reduced from the free-running 2.2 MHz to 885 kHz after MTS stabilization. The Allan deviation measurements of the beat signal between two locked lasers are 2.6 × 10 −11 / τ . This work provides a stable optical frequency reference for SERF atomic magnetometers and offers potential applications in extracting spatial information from optically pumped atoms.

Optics Express•May 16, 2025•5 citations
Abstract We experimentally generate polarization spectroscopy (error) signals corresponding to the D2-line hyperfine transitions, F g = 2 → F e = 1 , 2 , 3 of 87Rb, and F g = 3 → F e = 2 , 3 , 4 of 85Rb, and show that the strongest error signals correspond to the closed hyperfine transitions (oscillator strength ∼ 0.7 ), F g = 2 → F e = 3 and F g = 3 → F e = 4 , respectively. We make the generated error signal robust to fluctuations in external parameters by finding optimum values for the vapor cell temperature and pump-probe intensities at two different beam diameters. We further employ these optimized error signals to directly (without the need for frequency/phase modulation) lock the laser frequency—reducing the rms drift/linewidth from ∼ 10 MHz to < 500 kHz, when measured over a ∼ 60 min duration. In addition, by comparing theoretically calculated and experimentally measured error signals for the pump intensities ranging from ∼ 0.1 I sat 0 − 10 I sat 0 (where, I sat 0 ∼ 1.6 mW cm−2 is the two-level saturation intensity for the Rb D2-line transitions), we discuss the applicability and limitations of existing numerical and analytical approaches based on a full multi-level rate equation model for polarization spectroscopy.
We experimentally and theoretically investigated the optimal condition of polarization spectroscopy for frequency stabilization on various pump beam intensities and vapor cell temperatures for the D2 closed transition line of 87Rb atoms. We compared the experimental results, such as the amplitude, width, and slope, of the polarization spectroscopy signal with the theoretical results obtained from the numerical calculation of temporal density matrix equations. Based on the results, we found the optimal parameters, such as the pump beam intensity and vapor cell temperature, for polarization spectroscopy. The theoretically expected optimal parameters were, qualitatively, in good agreement with the experimental results.
Abstract Frequency-stabilized external cavity diode lasers are essential components of precision quantum experiments. Atomic hyperfine states involved in such experiments are very sensitive to laser frequency drifts and thus the accuracy of the results is directly linked to the stability of the laser source. The quality of the error signal determines the lock performance of the laser source. An optimum error signal provides protection against mechanical vibration, laser intensity noise, and ambient magnetic field fluctuations. We have discussed the optimization of the error signal shape profile for 133Cs D2 line, 62 S 1/2 F = 4 to 62 P 3/2 F’ = 4/5 crossover transition. For a non-optimum value, the peak-to-peak frequency drift is ∼ 8 MHz with the FWHM of the drift being 2.72 ± 0.3 MHz, whereas the FWHM for an optimized value is 436 ± 73 kHz showing a 6 times reduction. Also, the peak-to-peak frequency drift lies within 1.1 MHz measured for over 25 minutes which makes it suitable for use in high-precision spectroscopy and quantum experiments. Moreover, the optical layout allows possibility of further miniaturization which is quite crucial for field applications and deployable quantum sensors.
We study polarization spectroscopy of Rb vapour. A weak probe beam analyses the birefringence induced in a room temperature vapour by a strong counterpropagating circularly polarized pump beam. In contrast to most other work on polarization spectroscopy, we use a polarization beam splitting cube and two detectors (rather than a polarizer and one detector) to analyse the probe beam. The signal is in the form of a derivative of a Lorentzian. For theoretical analysis we study the closed atomic transition 5 2 S 1/2 ( F = 3) → 5 2 P 3/2 ( F ' = 4) in the D2 line of 85 Rb. We study the time needed to redistribute population among the m F states, derive an expression for the expected lineshape and present experimental data in excellent agreement with theory. The polarization spectrum provides an ideal error signal for frequency stabilization of a laser. We describe the geometry and parameters for optimizing the error signal.
Precise laser stabilization is a fundamental aspect of modern metrology, directly influencing the accuracy of fundamental measurements in fields such as high-precision metrology, atomic sensor applications, and quantum technologies. Saturation absorption spectroscopy (SAS) is one of the most effective techniques for achieving high spectral stability, as it enables laser frequencies to be locked to atomic resonances. This technique exploits the nonlinear interaction between a weaker probe beam and a stronger pump beam within a rubidium (Rb) atomic vapor cell. By eliminating Doppler broadening, SAS allows well-defined hyperfine transitions to be resolved, providing a reliable optical frequency reference. This study aims to optimize laser frequency stabilization using the SAS technique by investigating the effects of laser light polarization, atomic vapor cell temperature, and pump-probe power adjustments. Polarization-dependent selection rules influence transition probabilities, thereby affecting spectral contrast and frequency stability. Additionally, atomic density variations, which depend on the vapor cell temperature, influence signal strength and linewidth, necessitating precise temperature control for optimal performance. Furthermore, the pump power must be sufficient to induce saturation without excessive power broadening, while the probe power must remain low enough to prevent spectral line distortion. By optimizing polarization, temperature, and power parameters, the stabilization of the Rb atomic laser can be enhanced, leading to improved reproducibility and consistency in high-precision measurements. SAS-based laser stabilization is particularly crucial for atomic sensor applications and quantum technologies, where highly stable, narrow-linewidth lasers are essential for precision measurements. Applications such as atomic magnetometers, gyroscopes, and inertial navigation systems depend on precisely stabilized lasers for optimal performance. By enhancing the reliability of laser frequency stabilization, this work contributes to the advancement of next-generation atomic sensors with improved sensitivity and stability.
We make a detailed comparison of frequency modulation spectroscopy (FMS) and modulation transfer spectroscopy (MTS) and of their applications in stabilizing laser frequency. In both FMS and MTS, intensity modulations of probe beam are observed in saturated absorption spectroscopy of 87Rb atoms. However, the two modulation profiles appear different due to their distinct origins. Demodulation gives rise to frequency discrimination spectra, which can serve as error signals for frequency locking. The optimal error signal of FMS has a larger linear slope but also a slanted baseline, in contrast to that of MTS. We apply FMS and MTS to stabilize two 780 nm external cavity diode lasers to D2 lines of 87Rb atoms. We measure laser linewidth and stability using beat notes of two independently locked lasers. A laser linewidth as narrow as 12.9 kHz is achieved in FMS locking, compared to 70.8 kHz in MTS locking. A laser stability at the level of 10−12 is reached in both schemes. Nevertheless, FMS locking offers a better short-term stability, whereas MTS locking yields a smaller long-term drift. Our investigation of FMS and MTS would be valuable for making a choice of these spectroscopy techniques for laser stabilization as well as other relevant applications.
In a spin-exchange relaxation-free (SERF) atomic magnetometer, the pump and probe laser frequencies are tuned to the D 1 transition line of alkali metal atoms to enhance measurement sensitivity. The D 1 line, a non-cycling transition, exhibits a low absorption coefficient. This study theoretically analyzes the influence of different parameters on the absorption coefficient of the D 1 line and proposes a polarization-dependent approach to enhance it. A frequency stabilization method based on modulation transfer spectroscopy (MTS) with an enhanced absorption coefficient is introduced. Compared with the conventional method, optimizing the probe beam’s polarization increases the absorption coefficient, raising the amplitude of the MTS signal. The results show that using a stronger MTS signal for frequency stabilization reduces the laser's frequency noise. Using heterodyne measurement, we characterize the linewidth-narrowing effect of MTS locking and evaluate the frequency stability of the locked laser. The linewidth of each laser is reduced from the free-running 2.2 MHz to 885 kHz after MTS stabilization. The Allan deviation measurements of the beat signal between two locked lasers are 2.6 × 10 −11 / τ . This work provides a stable optical frequency reference for SERF atomic magnetometers and offers potential applications in extracting spatial information from optically pumped atoms.