Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Impedance matched superconducting nanowire photodetector for single- and multi-photon detection

Di Zhu

Published Oct 26, 2023• 0 citations
OpenAlex

Abstract

Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, IB×Zload, where Zload is limited to 50Ω in standard RF electronics. This limit is broken/exceeded by interfacing the 50Ω load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. The taper increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, a 3.6× higher pulse amplitude, 3.7× faster slew rate, and 25.1 ps smaller timing jitter was observed. The taper also makes the detector's output voltage sensitive to the number of photon-induced hotspots and enables photon number resolution.

Related papers

Superconducting nanowire single-photon detector with integrated impedance-matching taper

Di Zhu, Marco Colangelo, Boris A. Korzh +11 more

Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, IB × Zload, where Zload is limited to 50 Ω in standard r.f. electronics. Here, we break this limit by interfacing the 50 Ω load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. At the expense of reduced maximum counting rate, it increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, we experimentally observed a 3.6× higher pulse amplitude, 3.7× faster slew rate, and 25.1 ps smaller timing jitter. The results match our numerical simulation, which incorporates both the hotspot dynamics in the SNSPD and the distributed nature in the transmission line taper. The taper studied here may become a useful tool to interface high-impedance superconducting nanowire devices to conventional low-impedance circuits.

arXiv:1811.03991•Applied Physics Letters•Jan 28, 2019•40 citations

Improving Photon Number Resolution in Superconducting Nanowire Single-Photon Detectors with Integrated Impedance Tapers

Bladimiro E. Valbuena, Daniel F. Santavicca

Simulations are run to optimize the ability to resolve the number of photons detected from the pulse height by a Superconducting Nanowire Single-Photon Detector (SNSPD). This is set up in a manner that features an impedance-matching transmission line taper that provides a characteristic impedance which transitions from kΩ to 50 Ω, with the taper providing an effective load impedance that outputs pulses with not only larger amplitudes but also showed a distinct separation for multi-photon events. The first part of this project tries to computationally match the experimental results obtained by our collaborators at MIT. Once these results are achieved, we try to modify the device geometry to improve the key detector metrics which include timing jitter, dark count rate, reset time, and overall detection efficiency.

•Jan 1, 2020•0 citations

Resolving Photon Numbers Using a Superconducting Nanowire with Impedance-Matching Taper

Di Zhu, Marco Colangelo, Changchen Chen +4 more

Time- and number-resolved photon detection is crucial for quantum information processing. Existing photon-number-resolving (PNR) detectors usually suffer from limited timing and dark-count performance or require complex fabrication and operation. Here, we demonstrate a PNR detector at telecommunication wavelengths based on a single superconducting nanowire with an integrated impedance-matching taper. The taper provides a kΩ load impedance to the nanowire, making the detector's output amplitude sensitive to the number of photon-induced hotspots. The prototyping device was able to resolve up to four absorbed photons with 16.1 ps timing jitter and <2 c.p.s. device dark count rate. Its exceptional distinction between single- and two-photon responses is ideal for high-fidelity coincidence counting and allowed us to directly observe bunching of photon pairs from a single output port of a Hong-Ou-Mandel interferometer. This detector architecture may provide a practical solution to applications that require high timing resolution and few-photon discrimination.

arXiv:1911.09485•Nano Letters•Apr 9, 2020•103 citations

Photon-Number Resolution Using Superconducting Tapered Nanowire Detector

Di Zhu, Marco Colangelo, Changchen Chen +4 more

We show that a superconducting nanowire with an integrated impedance-matching taper can resolve photon numbers. The taper increases the nanowire detector’s output amplitude and makes it sensitive to the number of single-photon-induced hotspots.

Conference on Lasers and Electro-Optics•Jan 1, 2020•0 citations

Improvements of readout signal integrity in mid-infrared superconducting nanowire single-photon detectors

Sahil J. Patel, Marco Colangelo, Andrew D. Beyer +7 more

Superconducting nanowire single-photon detectors (SNSPDs) in the mid-infrared (MIR) have the potential to open up numerous opportunities in fields such as exoplanet searches, direct dark matter detection, physical chemistry, and remote sensing. One challenge in pushing SNSPD sensitivity to the MIR is a decrease in the signal-to-noise ratio (SNR) of the readout signal, as the critical currents become increasingly smaller. We overcome this trade-off with a device architecture that employs impedance matching tapers and superconducting nanowire avalanche photodetectors to demonstrate increased SNR while maintaining saturated internal detection efficiency at 7.4 μm and approaching saturation at 10.6 μm. This work provides a platform for pushing SNSPD sensitivity to longer wavelengths while enabling the scalability to large arrays.

arXiv:2401.15764•Applied Physics Letters•Apr 15, 2024•8 citations

WSi superconducting nanowire single photon detector with a temporal resolution below 5 ps

Boris A. Korzh, Qingyuan Zhao, Simone Frasca +10 more

Through the use of an impedance matched taper, be we demonstrate a reduction of the noise jitter in WSi SNSPDs to a level below the intrinsic effects, resulting in full-width at half-maximum values of 4.8 ps for 532 nm and 10.3 ps for 1550 nm single photons.

Conference on Lasers and Electro-Optics•Jan 1, 2018•14 citations
Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, IB×Zload, where Zload is limited to 50Ω in standard RF electronics. This limit is broken/exceeded by interfacing the 50Ω load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. The taper increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, a 3.6× higher pulse amplitude, 3.7× faster slew rate, and 25.1 ps smaller timing jitter was observed. The taper also makes the detector's output voltage sensitive to the number of photon-induced hotspots and enables photon number resolution.
Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, IB × Zload, where Zload is limited to 50 Ω in standard r.f. electronics. Here, we break this limit by interfacing the 50 Ω load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. At the expense of reduced maximum counting rate, it increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, we experimentally observed a 3.6× higher pulse amplitude, 3.7× faster slew rate, and 25.1 ps smaller timing jitter. The results match our numerical simulation, which incorporates both the hotspot dynamics in the SNSPD and the distributed nature in the transmission line taper. The taper studied here may become a useful tool to interface high-impedance superconducting nanowire devices to conventional low-impedance circuits.
Simulations are run to optimize the ability to resolve the number of photons detected from the pulse height by a Superconducting Nanowire Single-Photon Detector (SNSPD). This is set up in a manner that features an impedance-matching transmission line taper that provides a characteristic impedance which transitions from kΩ to 50 Ω, with the taper providing an effective load impedance that outputs pulses with not only larger amplitudes but also showed a distinct separation for multi-photon events. The first part of this project tries to computationally match the experimental results obtained by our collaborators at MIT. Once these results are achieved, we try to modify the device geometry to improve the key detector metrics which include timing jitter, dark count rate, reset time, and overall detection efficiency.
Time- and number-resolved photon detection is crucial for quantum information processing. Existing photon-number-resolving (PNR) detectors usually suffer from limited timing and dark-count performance or require complex fabrication and operation. Here, we demonstrate a PNR detector at telecommunication wavelengths based on a single superconducting nanowire with an integrated impedance-matching taper. The taper provides a kΩ load impedance to the nanowire, making the detector's output amplitude sensitive to the number of photon-induced hotspots. The prototyping device was able to resolve up to four absorbed photons with 16.1 ps timing jitter and <2 c.p.s. device dark count rate. Its exceptional distinction between single- and two-photon responses is ideal for high-fidelity coincidence counting and allowed us to directly observe bunching of photon pairs from a single output port of a Hong-Ou-Mandel interferometer. This detector architecture may provide a practical solution to applications that require high timing resolution and few-photon discrimination.
Superconducting nanowire single-photon detectors (SNSPDs) in the mid-infrared (MIR) have the potential to open up numerous opportunities in fields such as exoplanet searches, direct dark matter detection, physical chemistry, and remote sensing. One challenge in pushing SNSPD sensitivity to the MIR is a decrease in the signal-to-noise ratio (SNR) of the readout signal, as the critical currents become increasingly smaller. We overcome this trade-off with a device architecture that employs impedance matching tapers and superconducting nanowire avalanche photodetectors to demonstrate increased SNR while maintaining saturated internal detection efficiency at 7.4 μm and approaching saturation at 10.6 μm. This work provides a platform for pushing SNSPD sensitivity to longer wavelengths while enabling the scalability to large arrays.