So called quantum supremacy has been demonstrated by at least two groups utilising < 100 physical superconducting qubits cooled to milli-kelvin temperatures. It is acknowledged that scaling these efforts to fault-tolerant, general purpose quantum computers will require very many more logical qubits, each formed from several physical ones. Addressing and control of these qubits is an area of active research, but it is likely that increased cooling capacities, particularly at the lowest temperatures, will be a requirement for the realisation of systems beyond noisy intermediate-scale quantum processors. Here we demonstrate a method by which significantly increased cooling power at temperatures ∼ 200 mK can be generated without impacting on the performance of an adjacent stage providing cooling power at temperatures ∼ 20 mK.
So called quantum supremacy has been demonstrated by at least two groups utilising < 100 physical superconducting qubits cooled to milli-kelvin temperatures. It is acknowledged that scaling these efforts to fault-tolerant, general purpose quantum computers will require very many more logical qubits, each formed from several physical ones. Addressing and control of these qubits is an area of active research, but it is likely that increased cooling capacities, particularly at the lowest temperatures, will be a requirement for the realisation of systems beyond noisy intermediate-scale quantum processors. Here we demonstrate a method by which significantly increased cooling power at temperatures ∼ 200 mK can be generated without impacting on the performance of an adjacent stage providing cooling power at temperatures ∼ 20 mK.
Silicon spin qubits are a leading candidate for large-scale quantum computing owing to their compatibility with semiconductor manufacturing. However, scaling to useful fault-tolerant processors will likely generate thermal loads that exceed the cooling power available at millikelvin temperatures. Raising the operating temperature eases cooling requirements but reduces gate fidelity, increasing the overhead of quantum error correction. Identifying the operating temperature that minimizes total power consumption is therefore a key challenge for commercially viable quantum computers. Here, we use gate set tomography to benchmark two-qubit silicon chips fabricated in both industrial and academic environments over a range of temperatures. Elevated temperatures substantially shorten coherence times and increase gate and state-preparation-and-measurement infidelities. Based on these measurements, we develop a general power model for silicon quantum computers that combines cryogenic cooling requirements with error-correction overheads. We show that a finite optimal operating temperature exists and is strongly influenced by a crossover temperature near 1 K in current devices, above which gate fidelity degrades rapidly. These results connect device-level fidelity limitations to system-level power requirements, providing design guidelines for large-scale silicon quantum computers.
Current state-of-the-art superconducting microwave qubits are cooled to extremely low temperatures to avoid sources of decoherence. Higher qubit operating temperatures would significantly increase the cooling power available, which is desirable for scaling up the number of qubits in quantum computing architectures and integrating qubits in experiments requiring increased heat dissipation. To operate superconducting qubits at higher temperatures, it is necessary to address both quasiparticle decoherence (which becomes significant for aluminum junctions above 160 mK) and dephasing from thermal microwave photons (which are problematic above 50 mK). Using low-loss niobium-trilayer junctions, which have reduced sensitivity to quasiparticles due to the higher superconducting transition temperature of niobium, we fabricate transmons with higher frequencies than previously studied, up to 24 GHz. We measure decoherence and dephasing times of about 1 μ s , corresponding to average qubit quality factors of approximately 10 5 , and find that decoherence is unaffected by quasiparticles up to 1 K . Without relaxation from quasiparticles, we are able to explore dephasing from purely thermal sources, finding that our qubits can operate up to approximately 250 mK while maintaining similar performance. The thermal resilience of these qubits creates new options for scaling up quantum processors, enables hybrid quantum experiments with high heat-dissipation budgets, and introduces a material platform for even-higher-frequency qubits. Published by the American Physical Society 2024
Quantum computing promises an exponential speed-up of computation compared to what is nowadays achievable with classical computers. In this way, it enables the evaluation of more complex models and the breaching of current security algorithms. For the operation of a quantum system, many questions remain to be answered. Currently, there are several quantum technologies that promise to be both reliable and scalable, two features required for large scale quantum operations. Common to all technologies is the operating temperature that needs to be close to absolute zero, i.e. below 100 mK, to suppress environment noise and allow the quantum properties to become 'visible'. In order for any quantum processor to be operated, a so-called quantum-classical interface is required for the quantum bit (qubit) read-out and control. This interface consists of various electronic blocks, such as analog-to-digital converters, digital-to-analog converters, mixers, amplifiers and a digital controller. Especially the analog blocks require effort to meet the noise and stability constraints as not to disturb the very sensitive qubits and allow reading of the tiny signals. As the qubits live in extremely deep-cryogenic temperatures, long wires interface the cryogenic with the room temperature environment, where most of the electronics is situated. However, for a scalable system, heat injection becomes a serious problem, with many wires between 300 K and sub-Kelvin. Furthermore, such amount of interconnects is challenging to mechanically place in a dilution refrigerator. Therefore, in this work, we propose to implement the electronics not at room temperature, but at a temperature much closer to the qubits, for example at 4 K. This not only reduces significantly the wiring between room temperature and the qubits, but we can also benefit from lower electronic noise at such a temperature. The operation of conventional electronics almost 200°C below its normal temperature range is not trivial as device properties alter significantly and most circuits no longer operate as intended. In CMOS processes, the main technology in the integrated electronics world, the behaviour of the transistors, required for the implementation of any circuit, deviates considerably at low temperatures. The transistor's threshold voltage goes up, the mobility increases and the subthreshold slope becomes steeper, to name just a few of these deviations. Although there are improvements in performance, there are also some counter effects, and characterization of the transistors is needed to observe the changes. Once devices are characterized at such low temperatures, new models can be built and circuits can be simulated and adapted to operate properly at cryogenic temperatures. Luckily, there are various commercially available devices that can already withstand the chills of cold. We demonstrated various commercially available devices, such as a field-programmable gate array (FPGA) implemented in a 28 nm CMOS process, to be operating without major concerns at 4~K. Its properties alter only slightly, within 5 to 10%, and all tested circuit implementations, working at 300~K, also worked at 4 K. We combined both commercially available devices, that operate 200 K below their specified temperature range, with custom designed CMOS circuits to implement a cryogenic read-out platform for spin qubits. This system comprises amplifiers, an ADC, an FPGA, voltage regulators and a clock generator. It allows to amplify the tiny signal from the qubits and digitize it directly in the FPGA in order to process the data locally at 4~K. This system is one of the first systematic attempts at operating a part of the quantum-classical interface at cryogenic temperatures and forms the basis for future systems comprising the complete electronic interface for qubits to operate at such low temperatures. One of the main problems to tackle for cryogenic electronic systems is their power consumption. Power budgets are simply limited to roughly 1 or 2 Watts at 4 K and exponentially lower at deeper cryogenic temperatures, thus limiting the size of large-scale electronic systems. Our approach of combined commercial and custom circuits will have to be steadily replaced by a single (custom) technology that meets both power and scalability constraints. One of the best candidates is CMOS, a technology that the industry has relied upon for several decades and benefits from many optimizations thanks to Moore's law.
Quantum computing promises an exponentially higher computational power than classical computers; although all the building blocks have become available, certain constraints still prevent quantum advantage. The fundamental challenge in building a practical quantum computer is integrating thousands of highly coherent qubits with the control and readout electronics. The need for a high‐coherence qubit drives the effort for quantum error correction algorithms to create fault‐tolerant quantum systems. Error correction becomes tangible in a quantum processor only in large numbers of qubits. Thus, the other challenge is reducing the number of physical interconnects (coaxial lines) between the quantum–classical interface and bulky room‐temperature electronics. To interface thousands of qubits, interconnects can be reduced by bringing the control and readout electronics near the quantum processor. Cryogenic complementary metal–oxide–semiconductor (CMOS) technology has been an ideal candidate for this purpose. Integrated control and readout at cryogenic temperatures require low power dissipation circuit designs and techniques such as frequency‐division multiplexing (FDM) due to the finite cooling power of a dilution refrigerator. Herein, an overview of each building block in a superconducting quantum computer is provided, focusing on scalability. Furthermore, this article is concluded with an outlook discussing current challenges and future directions for the scalable superconducting control and readout.
Superconducting qubits are a leading platform for quantum computation, yet decoherence and scalability challenges continue to limit progress toward fault-tolerant systems. This review synthesizes research on architectures, noise sources, and error correction to clarify performance trade-offs and guide development. The transition from Transmon to Fluxonium has dramatically improved qubit performance, achieving millisecond-scale coherence times. However, this success reveals a fundamental limit of coherence now being primarily restricted by the physical properties of the materials, specifically dielectric losses occurring at the Josephson junction leads and within the surrounding materials. As overcoming these material limits becomes increasingly difficult, system-level engineering determines whether high-coherence qubits can scale.Scaling quantum systems is difficult because current cooling and control systems create too much heat and this forces a shift to integrated digital superconducting circuits and cryogenic light-based links. While these hardware challenges restrict scaling, experiments in error correction show that logical qubits can already outperform physical ones. For example, a distance-7 surface code improved logical qubit lifetime by 2.4×. Achieving practical fault tolerance, however, requires moving beyond simple error models. Future systems must combine techniques like Dynamical Decoupling and Machine Learning-based Optimal Control with dynamic classical control capable of handling complex, correlated faults such as Multi-Bit Burst Errors. Progress in materials, cryogenic system integration for control, and adaptive error management must advance together to realize scalable, high-fidelity quantum hardware.
Scaling superconducting quantum computers to the fault-tolerant regime calls for a commensurate scaling of the classical control and readout stack. Today's systems largely rely on room-temperature, rack-based instrumentation connected to dilution-refrigerator cryostats through many coaxial cables. Looking ahead, superconducting fault-tolerant quantum computers (FTQCs) will likely adopt a heterogeneous quantum-classical architecture that places selected electronics at cryogenic stages -- for example, cryo-CMOS at 4~K and superconducting digital logic at 4~K and/or mK stages -- to curb wiring and thermal-load overheads. This review distills key requirements, surveys representative room-temperature and cryogenic approaches, and provides a transparent first-order accounting framework for cryoelectronics. Using an RSA-2048-scale benchmark as a concrete reference point, we illustrate how scaling targets motivate constraints on multiplexing and stage-wise cryogenic power, and discuss implications for functional partitioning across room-temperature electronics, cryo-CMOS, and superconducting logic.