Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physical Review A

Burning and reading ensembles of spectral holes by optical frequency combs: Demonstration in rare-earth-doped solids and application to laser frequency stabilization

René Oswald, Alexander Yu. Nevsky, Stephan Schiller

Published Dec 13, 2021• 5 citations
Publisher

Abstract

We describe a spectroscopic method applicable to inhomogeneously broadened transitions. As a test system we use suitable rare-earth-doped solids in which persistent spectral holes can be burned on weakly allowed electronic transitions. These systems are of interest as frequency references for the stabilization of laser frequencies. In all experiments so far, spectral holes are burned and read out individually. Here we present a demonstration of simultaneous burning and readout of sets of spectral holes, containing up to 1024 individual spectral holes, by a comb of laser frequencies. The simultaneous readout of such a set leads to an effective compound signal that has a higher signal-to-noise ratio. Here, an improvement by a factor of 20 was obtained for a set of 512 spectral holes. We use the method to stabilize the frequency of a laser and characterize its stability.

DOI
10.1103/physreva.104.063111

Related papers

Spectral Hole Burning for Ultra-stable Lasers

Shuo Zhang, Nemanja Lučić, Nicolas Galland +6 more

Spectral hole burning in rare earth doped crystal can provide frequency references based on the optical transition of the dopant ions [1] . The narrow spectral patterns can be used to improve laser frequency stabilization [2] , [3] and provide a new generation of ultra-stable lasers with lower thermal noise benefiting from the cryogenic environment and better quality factor of the crystal than the amorphous glass typically used in the Fabry-Perot cavity. We utilize Europium doped yttrium silicon oxide (Eu:YSO) in our experiments, which allow realization of long lived (hours or more depending on temperature) narrow spectral holes ( kHz or less) well suited for high precision experiment applications. We will describe our novel double-heterodyne detection method [4] , used to decrease the detection noise, as well as experiments assessing quantitatively the sensitivity of the spectral pattern to crystal deformation [5] , [6] , application of electric field [7] and temperature fluctuations. We currently demonstrate a state-of-the-art laser frequency stability at 1.7 × 10 − 15 at 1s [4] , limited by the latter effect, for which improvement strategies have been demonstrated elsewhere [2] and which we are currently implementing. The other effects which we have quantitatively studied are compatible with a few 10 − 18 frequency stability at 1s time scale. This work is particularly promising in the context of optical frequency lattice clocks, for which the ultra-stable laser used for probing the clock transition is a strong limiting factor of the frequency stability.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 21, 2021•1 citation

Programmable frequency reference for laser stabilization using persistent spectral hole burning

Peter B. Sellin, Nick Strickland, John L. Carlsten +1 more

Summary form only given. The first known demonstration of laser frequency stabilization using a solid-state persistent spectral hole burning material as the frequency reference is reported. Unlike gas phase transitions or Fabry-Perot resonances, spectral holes for frequency references can be prepared at any frequency within a broad inhomogeneous absorption profile (15 GHz in the material demonstrated here). Several lasers may be stabilized to multiple spectral holes, either in the same or separate absorption bands, with arbitrary frequency separations.

Conference on Lasers and Electro-Optics•Jan 20, 2003•0 citations

Detection Techniques and Fundamental Limits in Frequency Stabilization via Spectral Hole Burning

Michael Hartman, Xiuji Lin, Benjamin Pointard +5 more

This poster presents the status of the development of an ultra-frequency stable laser via a spectroscopic technique known as Spectral Hole Burning (SHB). In short, we can use a pump laser to imprint, or ’burn’, transmissive spectral lines, or ’spectral holes’, in the otherwise inhomogeneously broadened absorptive spectral sites of a Eu3+ doped Y2SiO5 crystal. We can then lock a probe laser to these narrow spectral features achieving our frequency stabilized laser. Of great concern is the frequency stability of the spectral holes, such as their sensitivity to temperature changes which we characterize here. Additionally, a challenge this experiment faces is the restriction of probe laser power to avoid damaging the spectral features. This sets a relatively high level of shot noise, limiting the detection sensitivity. Here we present our solution to overcome this difficulty by using a multi-spectral- hole probing scheme to average the probing signals of several burned spectral holes.

•Nov 8, 2023•0 citations

Laser frequency stabilization using regenerative spectral hole burning

Peter B. Sellin, Nick Strickland, Thomas Böttger +2 more

Summary form only given. We introduce laser frequency stabilization using continuously regenerated transient spectral holes in an inhomogeneously broadened resonance of a solid. Narrow spectral holes provide extreme frequency stabilization for time scales appropriate for spectroscopy, signal processing, laser ranging, and interferometry. This technique thus will have significant applications beyond the field of spectral hole burning.

Conference on Lasers and Electro-Optics•Jan 1, 2000•1 citation

Hole-burning techniques for isolation and study of individual hyperfine transitions in inhomogeneously broadened solids demonstrated in Pr3+:Y2SiO5

Mattias Nilsson, Lars Rippe, Stefan Kröll +2 more

Due to their narrow homogeneous linewidths, rare-earth ions in inorganic crystals at low temperatures have recently been given considerable attention as test materials for experiments in coherent quantum optics. Because these narrow linewidth transitions have been buried in a wide inhomogeneous line, the scope of experiments that could be carried out in these materials has been limited. However, here we present spectroscopic techniques, based on spectral hole burning and optical pumping, which allow hyperfine transitions that are initially buried within an inhomogeneously broadened absorption line to be studied with no background absorption from other transitions. A sequence of hole-burning pulses is used to isolate selected transitions between hyperfine levels, which makes it possible to directly study properties of the transitions, e.g., transition strengths, and gives access to information that is difficult to obtain in standard hole-burning spectroscopy, such as the ordering of hyperfine levels. The techniques introduced are applicable to absorbers in a solid with long-lived sublevels in the ground state and where the homogeneous linewidth and sublevel separations are smaller than the inhomogeneous broadening of the optical transition. In particular, this includes rare-earth ions doped into inorganic crystals and in the present work the techniques are demonstrated in spectroscopy of ${\mathrm{Pr}}^{3+}$ in ${\mathrm{Y}}_{2}{\mathrm{SiO}}_{5}$. Information on the hyperfine structure and relative transition strengths of the $^{3}H_{4}\text{\ensuremath{-}}^{1}D_{2}$ hyperfine transitions in ${\mathrm{Pr}}^{3+}:{\mathrm{Y}}_{2}{\mathrm{SiO}}_{5}$ has been obtained from frequency-resolved absorption measurements, in combination with coherent and incoherent driving of the transitions.

arXiv:cond-mat/0408515•Physical Review B•Dec 30, 2004•201 citations

Laser stabilization at 1536 nm using regenerative spectral hole burning

Peter B. Sellin, Nick Strickland, Thomas Böttger +2 more

Laser frequency stabilization giving a 500-Hz Allan deviation for a 2-ms integration time with drift reduced to 7 kHz/min over several minutes was achieved at 1536 nm in the optical communication band. A continuously regenerated spectral hole in the inhomogeneously broadened ${}^{4}{I}_{15/2}{(1)}^{4}{I}_{13/2}(1)$ optical absorption of an ${\mathrm{Er}}^{3+}:{\mathrm{Y}}_{2}{\mathrm{SiO}}_{5}$ crystal was used as the short-term frequency reference, while a variation on the locking technique allowed simultaneous use of the inhomogeneously broadened absorption line as a long-term reference. The reported frequency stability was achieved without vibration isolation. Spectral hole burning frequency stabilization provides ideal laser sources for high-resolution spectroscopy, real-time optical signal processing, and a range of applications requiring ultra-narrow-band light sources or coherent detection; the time scale for stability and the compatibility with spectral hole burning devices make this technique complementary to other frequency references for laser stabilization.

Physical review. B, Condensed matter•Mar 30, 2001•51 citations
We describe a spectroscopic method applicable to inhomogeneously broadened transitions. As a test system we use suitable rare-earth-doped solids in which persistent spectral holes can be burned on weakly allowed electronic transitions. These systems are of interest as frequency references for the stabilization of laser frequencies. In all experiments so far, spectral holes are burned and read out individually. Here we present a demonstration of simultaneous burning and readout of sets of spectral holes, containing up to 1024 individual spectral holes, by a comb of laser frequencies. The simultaneous readout of such a set leads to an effective compound signal that has a higher signal-to-noise ratio. Here, an improvement by a factor of 20 was obtained for a set of 512 spectral holes. We use the method to stabilize the frequency of a laser and characterize its stability.
Spectral hole burning in rare earth doped crystal can provide frequency references based on the optical transition of the dopant ions [1] . The narrow spectral patterns can be used to improve laser frequency stabilization [2] , [3] and provide a new generation of ultra-stable lasers with lower thermal noise benefiting from the cryogenic environment and better quality factor of the crystal than the amorphous glass typically used in the Fabry-Perot cavity. We utilize Europium doped yttrium silicon oxide (Eu:YSO) in our experiments, which allow realization of long lived (hours or more depending on temperature) narrow spectral holes ( kHz or less) well suited for high precision experiment applications. We will describe our novel double-heterodyne detection method [4] , used to decrease the detection noise, as well as experiments assessing quantitatively the sensitivity of the spectral pattern to crystal deformation [5] , [6] , application of electric field [7] and temperature fluctuations. We currently demonstrate a state-of-the-art laser frequency stability at 1.7 × 10 − 15 at 1s [4] , limited by the latter effect, for which improvement strategies have been demonstrated elsewhere [2] and which we are currently implementing. The other effects which we have quantitatively studied are compatible with a few 10 − 18 frequency stability at 1s time scale. This work is particularly promising in the context of optical frequency lattice clocks, for which the ultra-stable laser used for probing the clock transition is a strong limiting factor of the frequency stability.
Summary form only given. The first known demonstration of laser frequency stabilization using a solid-state persistent spectral hole burning material as the frequency reference is reported. Unlike gas phase transitions or Fabry-Perot resonances, spectral holes for frequency references can be prepared at any frequency within a broad inhomogeneous absorption profile (15 GHz in the material demonstrated here). Several lasers may be stabilized to multiple spectral holes, either in the same or separate absorption bands, with arbitrary frequency separations.
This poster presents the status of the development of an ultra-frequency stable laser via a spectroscopic technique known as Spectral Hole Burning (SHB). In short, we can use a pump laser to imprint, or ’burn’, transmissive spectral lines, or ’spectral holes’, in the otherwise inhomogeneously broadened absorptive spectral sites of a Eu3+ doped Y2SiO5 crystal. We can then lock a probe laser to these narrow spectral features achieving our frequency stabilized laser. Of great concern is the frequency stability of the spectral holes, such as their sensitivity to temperature changes which we characterize here. Additionally, a challenge this experiment faces is the restriction of probe laser power to avoid damaging the spectral features. This sets a relatively high level of shot noise, limiting the detection sensitivity. Here we present our solution to overcome this difficulty by using a multi-spectral- hole probing scheme to average the probing signals of several burned spectral holes.
Due to their narrow homogeneous linewidths, rare-earth ions in inorganic crystals at low temperatures have recently been given considerable attention as test materials for experiments in coherent quantum optics. Because these narrow linewidth transitions have been buried in a wide inhomogeneous line, the scope of experiments that could be carried out in these materials has been limited. However, here we present spectroscopic techniques, based on spectral hole burning and optical pumping, which allow hyperfine transitions that are initially buried within an inhomogeneously broadened absorption line to be studied with no background absorption from other transitions. A sequence of hole-burning pulses is used to isolate selected transitions between hyperfine levels, which makes it possible to directly study properties of the transitions, e.g., transition strengths, and gives access to information that is difficult to obtain in standard hole-burning spectroscopy, such as the ordering of hyperfine levels. The techniques introduced are applicable to absorbers in a solid with long-lived sublevels in the ground state and where the homogeneous linewidth and sublevel separations are smaller than the inhomogeneous broadening of the optical transition. In particular, this includes rare-earth ions doped into inorganic crystals and in the present work the techniques are demonstrated in spectroscopy of Pr3+{\mathrm{Pr}}^{3+}Pr3+ in Y2SiO5{\mathrm{Y}}_{2}{\mathrm{SiO}}_{5}Y2​SiO5​. Information on the hyperfine structure and relative transition strengths of the $^{3}H_{4}\text{\ensuremath{-}}^{1}D_{2}$ hyperfine transitions in Pr3+:Y2SiO5{\mathrm{Pr}}^{3+}:{\mathrm{Y}}_{2}{\mathrm{SiO}}_{5}Pr3+:Y2​SiO5​ has been obtained from frequency-resolved absorption measurements, in combination with coherent and incoherent driving of the transitions.
Laser frequency stabilization giving a 500-Hz Allan deviation for a 2-ms integration time with drift reduced to 7 kHz/min over several minutes was achieved at 1536 nm in the optical communication band. A continuously regenerated spectral hole in the inhomogeneously broadened 4I15/2(1)4I13/2(1){}^{4}{I}_{15/2}{(1)}^{4}{I}_{13/2}(1)4I15/2​(1)4I13/2​(1) optical absorption of an Er3+:Y2SiO5{\mathrm{Er}}^{3+}:{\mathrm{Y}}_{2}{\mathrm{SiO}}_{5}Er3+:Y2​SiO5​ crystal was used as the short-term frequency reference, while a variation on the locking technique allowed simultaneous use of the inhomogeneously broadened absorption line as a long-term reference. The reported frequency stability was achieved without vibration isolation. Spectral hole burning frequency stabilization provides ideal laser sources for high-resolution spectroscopy, real-time optical signal processing, and a range of applications requiring ultra-narrow-band light sources or coherent detection; the time scale for stability and the compatibility with spectral hole burning devices make this technique complementary to other frequency references for laser stabilization.