When the word diamond comes up, the majority of people thinks about engagement rings or gemstones. In fact, it is additionally, one of the most promising host materials for the implementation of advanced technology, exploiting the nature of quantum physics. Such quantum technologies have disruptive potential, ones the quantum effects can be applied in macroscopic, commercial products. The nitrogen-vacancy (NV) centre in diamond is a promising candidate to perform such tasks in the fields of quantum computation, quantum cryptography or metrology. Especially in the field of quantum sensing, the NV sensor impresses with nano-scale spatial resolution paired with high sensitivity. The electronic spin of the atomic-sized point defect can be initialised, manipulated and read-out at ambient conditions and coherence lifetimes are comparably long. Diamond magnetometers based on negatively charged NV centres have shown to be very attractive, and the sensitivity goes down to the single-atom level. In order to exploit such a high sensitivity level for sensing prospects, in this thesis, the NV centres are fabricated well confined in a certain distance to the diamond surface, since the detectable field usually decays with the third power of the distance between sensor and target. The surface depicts a fracture of the spin wise protecting diamond lattice and charge fluctuations affect the stability of NV centres, which are overcome by diamond surface termination. In order to improve the sensitivity further, the sensor density, measurement contrast and interaction time are increased. The nitrogen doping technique, which is applied during a plasma-enhanced chemical vapour deposition (PECVD) diamond growth process is used to fabricate NV centre ensembles aligned along one diamond crystal axis, thereby improving the measurement contrast by a factor up to four. The interaction time limiting spin bath is analysed using the sensor capabilities of the NVs, which leads to enhanced growth strategies and the fabrication of sensitivity optimised NV centre ensembles for magnetometry applications.
When the word diamond comes up, the majority of people thinks about engagement rings or gemstones. In fact, it is additionally, one of the most promising host materials for the implementation of advanced technology, exploiting the nature of quantum physics. Such quantum technologies have disruptive potential, ones the quantum effects can be applied in macroscopic, commercial products. The nitrogen-vacancy (NV) centre in diamond is a promising candidate to perform such tasks in the fields of quantum computation, quantum cryptography or metrology. Especially in the field of quantum sensing, the NV sensor impresses with nano-scale spatial resolution paired with high sensitivity. The electronic spin of the atomic-sized point defect can be initialised, manipulated and read-out at ambient conditions and coherence lifetimes are comparably long. Diamond magnetometers based on negatively charged NV centres have shown to be very attractive, and the sensitivity goes down to the single-atom level. In order to exploit such a high sensitivity level for sensing prospects, in this thesis, the NV centres are fabricated well confined in a certain distance to the diamond surface, since the detectable field usually decays with the third power of the distance between sensor and target. The surface depicts a fracture of the spin wise protecting diamond lattice and charge fluctuations affect the stability of NV centres, which are overcome by diamond surface termination. In order to improve the sensitivity further, the sensor density, measurement contrast and interaction time are increased. The nitrogen doping technique, which is applied during a plasma-enhanced chemical vapour deposition (PECVD) diamond growth process is used to fabricate NV centre ensembles aligned along one diamond crystal axis, thereby improving the measurement contrast by a factor up to four. The interaction time limiting spin bath is analysed using the sensor capabilities of the NVs, which leads to enhanced growth strategies and the fabrication of sensitivity optimised NV centre ensembles for magnetometry applications.
Abstract Diamond hosts a wide variety of colour centres that have demonstrated outstanding optical and spin properties. Among them, the nitrogen-vacancy (NV) centre is by far the most investigated owing to its superior characteristics, which promise the development of highly sophisticated quantum devices, in particular for sensing applications. Nevertheless, harnessing the potential of these centres mainly relies on the availability of high quality and purity diamond single crystals that need to be specially designed and engineered for this purpose. Plasma assisted chemical vapour deposition (CVD) has become a key enabling technology in this field of research. Nitrogen can indeed be directly doped in situ into a high crystalline quality diamond matrix in a controlled way, allowing the production of single isolated centres or ensembles that can potentially be integrated into a device. In this paper we will provide an overview of the requirements for synthesizing ‘quantum-grade’ diamond films using CVD. These include the reduction of impurities and surrounding spins that limit coherence times, the control of NV density in a wide range of concentrations as well as their spatial localization within the diamond. Enhancing the charge state and preferential orientation of the colour centres is also discussed. These improvements in material fabrication have contributed to positioning diamond as one of the most promising solid-state quantum systems and the first industrial applications in sensing are just starting to emerge.
The Nitrogen-Vacancy (NV) color center is a defect of diamond which behaves as an artificial atom hosted in a solid-state matrix. Due to its electron spin properties which can be read-out and manipulated as an elementary quantum system, the NV center has found a wide panel of applications as a qubit for quantum information and as a magnetic field sensor. However these applications require to control the properties of the NV centers and their localization. This doctoral thesis investigates methods allowing us to tailor the properties of NV centers by combining techniques for the implantation of nitrogen atoms and the plasma-assisted (CVD) synthesis of diamond.The manuscript is divided into six chapters. The first chapter summarizes the properties of the NV center which will set our objectives for the NV engineering. The second chapter will describe how arrays of NV centers can be created using Focused Ion Beam implantation. The results open a wide range of applications for the targeted creation of NV centers in diamond structures such as photonic crystals and tips. However the low kinetic energy which is required for achieving implantation within a spot of 10-nm diameter leads to shallow defects which properties are strongly affected by the sample surface. The third chapter investigates how the overgrowth of a diamond layer over implanted NV centers can remove the detrimental influence of the surface. The fourth and fifth chapters describe effective methods for NV center fabrication through the control of the CVD growth conditions of the hosting crystal. Thin layers with high NV doping can be grown and almost perfect control of the orientation of the NV axis can be achieved. With the goal to optimize the spin coherence properties, the sixth chapter investigates how the electron spin of the NV center can be protected from decoherence effects induced by magnetic noise due to the unpolarized spins in the diamond lattice.
Diamond is unique. Whether mechanical, thermal, electrical or optical, its properties are within the most extreme compared to those of any other material. This, together with the fact that in the last fifty years the synthesis of artificial diamond has become a reality, makes it very attractive for engineering and technological purposes. The range of diamond-based applications is very diverse and, among the others, includes its use in mechanical machining, high-power high-frequency electronics and high transmissivity optics. -- Diamond is also host to a wide variety of crystallographic defects. Appropriately controlled, they can be used to tune the characteristics of the material, but even more interestingly they often possess attractive optical properties on their own. In particular, nitrogen-vacancy (NV) centres in diamond have been the subject of extensive study in the last few years. They possess unique room-temperature optical and spin properties which make them promising systems for solid-state qubits in quantum information technologies and for emerging applications in biotechnology, nanomedicine and high resolution magnetometry, such as drug delivery, fluorescent biomarking and spin imaging. -- This thesis is focused on NV centres in diamond. I first present an extensive review on diamond as a material, describing in detail its physical properties, the methods that have been developed to synthesise it and some of its possible applications. I then move the attention specifically to NV centres in nanodiamonds (NDs), i.e. diamond crystals in the nanometre size range (0-100 nm). They are a potential candidate for emerging technologies including high-resolution magnetometry and biomedical imaging. For these applications, specific material requirements, such as the small size of the diamond nanocrystals and the optical stability of the hosted NV centres, are crucial. The NV stability with respect to the nanodiamond size and surface is the central theme of this thesis. I analyse the optical behaviour of NV centres in nanodiamond while varying a number of key parameters such as size, surface termination and diamond origin. Based on the measurements, I conclude whether the nanodiamond size and the NV surface proximity are factors that must be taken into consideration in order to control the material and realise nanotechnologies based on NV centres in nanodiamonds.
The fluorescence of the nitrogen-vacancy (NV) centre in artificial diamond has been widely studied for applications such as quantum communication protocols, quantum computation, fluorescence-based biolabelling, and optical sensing. Optical sensing by itself encompasses a wide range of possible applications: from magnetic and electric field sensing to temperature sensing and enabling, for example, the detection of paramagnetic ions and the identification of molecules by nuclear magnetic resonance. Compared to many other systems capable of optical sensing, the NV centre works at room temperature, and its spin-dependent fluorescence emission is the key property to achieve a high sensitivity to the surrounding environment. Additionally, the NV centre emission is highly photostable, has a relatively short lifetime (~ 12ns) and spans a broad wavelength range, from the red to the near-infrared region of the electromagnetic spectrum (600 - 800nm). While the common denominator of all mentioned applications is the NV centre, the properties of the artificial diamond surrounding the NV centre have a significant impact on its sensing performance. At present, the processing of artificial diamond has not been fully optimised, and research and development towards the realisation of the `best¿ diamond sample for optical sensing is far from over. Specifically, the role of other defects in diamond and their effects on the photo-physical properties of the NV centres are not entirely understood. In this thesis, I will discuss the potential benefits of a novel processing technique to create ensembles of NV centres, and the importance that surrounding nitrogen defects has on the achievable magnetic field sensitivity. Additionally, I will show both theoretical and experimental investigations of the NV centres photo-physical processes, with focus on magnetic field sensing. I will initially explore a protocol for microwave-free magnetometry. This protocol predicts a theoretical magnetic field sensitivity <10µT/√Hz in the range 0.3 - 30mT and I will demonstrate it experimentally with a maximum sensitivity of 3.6mT/Hz. Following, I will focus on exploring techniques to increase the magnetic field sensitivity by improving the material properties of the diamond samples. I will demonstrate that the simultaneous electron irradiation and annealing improves the creation efficiency of an ensemble of NV centres by up to 117%. Finally, I will investigate how substitutional nitrogen defects in the surrounding lattice affects the charge state of the NV centre, its emission intensity, its lifetime and its magnetic field sensitivity. I will study a sample characterised by multiple regions across its volume, with nitrogen concentration changing between 10ppm and 100ppm in each region. There si an optimal region with ~ 40ppm of substitutional nitrogen which demonstrates the highest fluorescence emission, mainly from the negatively-charged NV centre, and the highest magnetic field sensitivity of 1.6 ± 0.2µT/√Hz. However, both the regions with lower and higher substitutional nitrogen concentration than the optimal region show lower emission intensity and worse magnetic field sensitivity. Following is a summary of the content in each chapter: Chapter 1 will present an introduction to the diamond material and the classification of artificial diamond samples. It will introduce the NV centre, its fluorescence properties and the process to create NV centres in diamond. The chapter will also introduce the concepts around optical magnetometry and the working principle that allows the NV centre to sense magnetic fields as well as other external quantities, such as temperature or pressure. Finally, it will include a brief overview of the defects that are found in artificial diamond or are created during the sample processing. Chapter 2 will describe the working principle of the instruments utilised in this work. I will list the details of each instrument and describe the methods used for the analysis of the data. Chapter 3 will introduce the background of modelling the fluorescence emission from NV centres. I will discuss the implementation of a computational model based on the Lindblad master equation to simulate the photo-physical dynamics of the NV centre. I will demonstrate the successful simulation of the saturation emission, fluorescence lifetime and optically detected magnetic resonance using the theoretical model. Finally, I will explore the theoretically predicted sensitivity of microwave-free magnetometry, based on the NV centre emission intensity change under an external magnetic field. Chapter 4 will demonstrate experimentally the microwave-free magnetometry technique. In relation to the study of microwave-free magnetometry, this chapter will explore an unexpected increase in emission intensity at high magnetic fields > 100mT. Combining the experimental observations and the theoretical simulation developed in the previous chapter, I will identify and discuss a phenomenological decrease in the NV centre transition rate from the triplet state to the singlet state. The chapter will conclude comparing the experimental and theoretical sensitivities associated with the microwave-free magnetometry technique. Chapter 5 will show the characterisation of a diamond sample at each step of the process to create NV centres. I will study the electron irradiation followed by separate annealing on a high-pressure high-temperature diamond sample. I will then characterise the sample employing visible and infrared absorption spectroscopy, as well as measure the fluorescence spectra and lifetime of the defects identified at each step. Chapter 6 will examine an alternative method to create NV centres in diamond. I will compare diamond samples irradiated and annealed separately with samples simultaneously irradiated and annealed (referred to as 'annealing in situ'). To compare the two processes, I will estimate the concentration of nitrogen defects and NV centres and calculate their N-to-NV conversion efficiency. Chapter 7 will discuss the effects of substitutional nitrogen on the properties of the NV centres in diamond. For this discussion, I will use a single-crystal diamond that shows the presence of 4 growth sectors. Each growth sector is characterised by a different nitrogen concentration, as I will demonstrate at the beginning of the chapter. I will focus on 4 main properties affected by the concentration of nitrogen in the different sectors: the balance between the charge states of the NV centre, the overall fluorescence intensity from each sector, the fluorescence lifetime and its relation to non-radiative processes, and the magnetic field sensitivity obtained with the optically detected magnetic resonance technique. Chapter 8 will gather the results and conclusions of the entire body of work. It will also discuss future avenues of research in the topic of diamond processing and characterisations, to improve the existing optical sensing applications.
Because of their high sensitivity, quantum materials are extremely promising for new technologies. The main challenge lies in maintaining a sufficiently quantum coherence times for quantum computation or quantum sensing systems. NV centers in diamond which are point defects consisting of a substitutional nitrogen atom neighboring an atomic vacancy, where an electron pair can reside in a triplet state – are ideal candidates for the development of industrial-scale quantum systems. These spin states exhibit ms-long coherence times at room temperature and can be manipulated optically, hence opening interesting perspectives for sending magnetic fields with high sensitivity1.At HiQuTe Diamond, we take up the challenge of mastering the entire nitrogen-doped diamond production chain synthesized by Microwave Plasma-Assisted Chemical Vapor Deposition (MPACVD). We aim at creating affordable diamonds specially engineered to achieve long coherence times with high NV density and high doping uniformity. This quest require to overcome the impact of several external factors that contribute to electron spin decoherence. First, the chemical composition of the diamond, specifically the types and concentrations of impurities within the diamond matrix (such as substitutional nitrogen NS, NV centres, mono-vacancies and clusters, hydrogen, etc.), as well as their electrical charge states (NS⁰, NS⁺, NV⁰, NV⁻) should be carefully controlled. Thanks to extensive scientific research conducted over the past decade, combined with our own R&D efforts, we are now able to quantify these parameters using experimental techniques compatible with industrial applications (Raman and UV-Vis spectroscopy) and compare our results with key performance indicators2. Second, we study the relationship between coherence (T2*) and strain inhomogeneities in our diamond layers, which we analyse using birefringence measurements. Our findings demonstrate our capability to produce CVD diamond layers with reduced strain and extended defect and confirm that strain could be a critical limiting factor for T2*.In this poster, I will review the efforts carried out at HiQuTe Diamond to develop specific material that is well suited for quantum sensing applications.References1.Barry, J. F., Schloss, J. M., Bauch, E., Turner, M. J., Hart, C. A., Pham, L. M., & Walsworth, R. L. (2020). Sensitivity optimization for NV-diamond magnetometry. Reviews of Modern Physics, 92(1), 015004.2.Langer, J. (2022). Quantum-grade diamond for cavity-based solutions. Fraunhofer Verlag.
In modern-day quantum metrology, quantum sensors are widely employed to detect weak magnetic fields or nanoscale signals. Quantum devices, exploiting quantum coherence, are inevitably connected to physical constants and can achieve accuracy, repeatability, and precision approaching fundamental limits. As a result, these sensors have shown utility in a wide range of research domains spanning both science and technology. A rapidly emerging quantum sensing platform employs atomic-scale defects in crystals. In particular, magnetometry using nitrogen-vacancy (NV) color centers in diamond has garnered increasing interest. NV systems possess a combination of remarkable properties, optical addressability, long coherence times, and biocompatibility. Sensors based on NV centers excel in spatial resolution and magnetic sensitivity. These diamond-based sensors promise comparable combination of high spatial resolution and magnetic sensitivity without cryogenic operation. The above properties of NV magnetometers promise increasingly integrated quantum measurement technology, as a result, they have been extensively developed with various protocols and find use in numerous applications spanning materials characterization, nuclear magnetic resonance (NMR), condensed matter physics, paleomagnetism, neuroscience and living systems biology, and industrial vector magnetometry. In this chapter, NV centers are explored for magnetic sensing in a number of contexts. In general, we introduce novel regimes for magnetic-field probes with NV ensembles. Specifically, NV centers are developed for sensitive magnetometers for applications where microwaves (MWs) are prohibitively invasive and operations need to be carried out under zero ambient magnetic field. The primary goal of our discussion is to improve the utility of these NV center-based magnetometers.