Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Final Report

The 3 kHz SQUID receiver development

M. B. Simmonds, W. A. Fertig, R. P. Giffard

Published May 1, 1978• 0 citations
OpenAlex

Abstract

We have designed and tested a model for a 3 kHz receiver using a superconducting antenna circuit and a SQUID (Superconducting QUantum Interference Device) amplifier. Q factors as high as 6400 have been demonstrated for the resonant antenna, giving it an extremely low intrinsic noise voltage. We have anlayzed and solved various problems of matching between antenna and SQUID, as well as measuring noise, contributed by materials in the surrounding cryostat. We have been able to use feedback from the SQUID amplifier into the antenna to effectively broaden the 3 dB bandwidth to 1200 Hz without raising the noise level of the system significantly. By scaling the results obtained with our model receiver to an antenna volume of .022 M-cubed we have been able to estimate that a noise level of 2.4 x 10 to the -17th power T/(sq.rt. Hz) could be obtained in a 100 Hz bandwidth. (Author)

Related papers

Computational and Mathematical Modeling of Coupled Superconducting Quantum Interference Devices

Susan A. E. Berggren

This research focuses on conducting an extensive computational investigation and mathematical analysis into the average voltage response of arrays of Superconducting Quantum Interference Devices (SQUIDs). These arrays will serve as the basis for the development of a sensitive, low noise, signifcantly lower Size, Weight and Power (SWaP) antenna integrated with Low-Noise Amplifier (LNA) using the SQUID technology. The goal for this antenna is to be capable of meeting all requirements for Guided Missile Destroyers (DDG) 1000 class ships for Information Operations/Signals Intelligence (IO/SIGINT) applications in Very High Frequency/Ultra High Frequency (V/UHF) bands. The device will increase the listening capability of receivers by moving technology into a new regime of energy detection allowing wider band, smaller size, more sensitive, stealthier systems. The smaller size and greater sensitivity will allow for ships to be "de-cluttered" of their current large dishes and devices, replacing everything with fewer and smaller SQUID antenna devices. The fewer devices present on the deck of a ship, the more invisible the ship will be to enemy forces. We invent new arrays of SQUIDs, optimized for signal detection with very high dynamic range and excellent spur-free dynamic range, while maintaining extreme small size (and low radar cross section), wide bandwidth, and environmentally noise limited sensitivity, effectively shifting the bottle neck of receiver systems forever away from the antenna itself deeper into the receiver chain. To accomplish these goals we develop and validate mathematical models for different designs of SQUID arrays and use them to invent a new device and systems design. This design is capable of significantly exceeding, per size weight and power, state-of-the-art receiver system measures of performance, such as bandwidth, sensitivity, dynamic range, and spurious-free dynamic range.

•Jan 1, 2012•13 citations

Very low noise, tightly coupled, dc SQUID amplifiers

B. Muhlfelder, J. A. Beall, Michael W. Cromar +1 more

We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.

Applied Physics Letters•Oct 27, 1986•19 citations

Demonstration of SQUID (Superconducting QUantum Interference Device) parametric amplifier

Arnold H. Silver, R. Sandell, Reggie Phillips +1 more

This is the first Annual Report of an effort to demonstrate a low noise superconducting microwave amplifier. The amplifier is a nearly degenerate, single idler parametric amplifier which uses the nonlinear inductance of a single junction SQUID (Superconducting Quantum Interference Device). The design frequency is 9 GHz, 10 dB gain, and 16% bandwidth. In order to maximize the saturation power, the device impedance was chosen near 1ohm and a matching network was designed to transform to 50ohm. In later designs, a coherent array of SQUIDs is expected to increase the power and impedance. This report includes the design and test of the 50ohm to 1ohm broadband transformer, design and fabrication of the SQUID amplifier, and both saturation and noise analyses of the single SQUID and SQUID array. The analytical results, reported to the 1982 Applied Superconductivity Conference are: the noise temperature of the single SQUID parametric amplifier is equal to the amplifier termination temperature T(o), the response is linear to several percent of the flux quantum energy in the SQUID: the amplifier will be saturated by broad band noise if the noise source temperature is much greater than 10 To; and the array parametric amplifier has the same noise temperature as the single device indicating an N-fold increase in dynamic range. (Author)

Annual Report•Nov 1, 1982•0 citations

Low-noise ultra-high-speed dc SQUID readout electronics

D. Drung, Colmar Hinnrichs, H.-J. Barthelmess

User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.

Superconductor Science and Technology•Feb 27, 2006•76 citations

Improved dc SQUID read-out electronics with low 1/f noise preamplifier

D. Drung

An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.

Review of Scientific Instruments•Nov 1, 1997•43 citations

A DC SQUID amplifier with a novel tuning circuit

Tetsuya Takami, Takashi Noguchi, Koichi Hamanaka

The authors report a SQUID (superconducting quantum interference device) amplifier with a novel tuning circuit that can be easily coupled to a finite-impedance source. The SQUID amplifier is designed for a source impedance of 50 Omega and a signal frequency of nearly 150 MHz. The performance of the SQUID amplifier has been measured at 4.2 K. The measured gain and noise temperature of the SQUID amplifier are 20 dB and 0.7 K, respectively. A saturation temperature as high as 200 K at the input of the SQUID amplifier is achieved. It is concluded that this type of tuned SQUID amplifier is applicable to the IF (intermediate frequency) amplifier of the SIS (superconductor-insulator-semiconductor) receiver.>

IEEE Transactions on Magnetics•Mar 1, 1989•15 citations
We have designed and tested a model for a 3 kHz receiver using a superconducting antenna circuit and a SQUID (Superconducting QUantum Interference Device) amplifier. Q factors as high as 6400 have been demonstrated for the resonant antenna, giving it an extremely low intrinsic noise voltage. We have anlayzed and solved various problems of matching between antenna and SQUID, as well as measuring noise, contributed by materials in the surrounding cryostat. We have been able to use feedback from the SQUID amplifier into the antenna to effectively broaden the 3 dB bandwidth to 1200 Hz without raising the noise level of the system significantly. By scaling the results obtained with our model receiver to an antenna volume of .022 M-cubed we have been able to estimate that a noise level of 2.4 x 10 to the -17th power T/(sq.rt. Hz) could be obtained in a 100 Hz bandwidth. (Author)
This research focuses on conducting an extensive computational investigation and mathematical analysis into the average voltage response of arrays of Superconducting Quantum Interference Devices (SQUIDs). These arrays will serve as the basis for the development of a sensitive, low noise, signifcantly lower Size, Weight and Power (SWaP) antenna integrated with Low-Noise Amplifier (LNA) using the SQUID technology. The goal for this antenna is to be capable of meeting all requirements for Guided Missile Destroyers (DDG) 1000 class ships for Information Operations/Signals Intelligence (IO/SIGINT) applications in Very High Frequency/Ultra High Frequency (V/UHF) bands. The device will increase the listening capability of receivers by moving technology into a new regime of energy detection allowing wider band, smaller size, more sensitive, stealthier systems. The smaller size and greater sensitivity will allow for ships to be "de-cluttered" of their current large dishes and devices, replacing everything with fewer and smaller SQUID antenna devices. The fewer devices present on the deck of a ship, the more invisible the ship will be to enemy forces. We invent new arrays of SQUIDs, optimized for signal detection with very high dynamic range and excellent spur-free dynamic range, while maintaining extreme small size (and low radar cross section), wide bandwidth, and environmentally noise limited sensitivity, effectively shifting the bottle neck of receiver systems forever away from the antenna itself deeper into the receiver chain. To accomplish these goals we develop and validate mathematical models for different designs of SQUID arrays and use them to invent a new device and systems design. This design is capable of significantly exceeding, per size weight and power, state-of-the-art receiver system measures of performance, such as bandwidth, sensitivity, dynamic range, and spurious-free dynamic range.
We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.
This is the first Annual Report of an effort to demonstrate a low noise superconducting microwave amplifier. The amplifier is a nearly degenerate, single idler parametric amplifier which uses the nonlinear inductance of a single junction SQUID (Superconducting Quantum Interference Device). The design frequency is 9 GHz, 10 dB gain, and 16% bandwidth. In order to maximize the saturation power, the device impedance was chosen near 1ohm and a matching network was designed to transform to 50ohm. In later designs, a coherent array of SQUIDs is expected to increase the power and impedance. This report includes the design and test of the 50ohm to 1ohm broadband transformer, design and fabrication of the SQUID amplifier, and both saturation and noise analyses of the single SQUID and SQUID array. The analytical results, reported to the 1982 Applied Superconductivity Conference are: the noise temperature of the single SQUID parametric amplifier is equal to the amplifier termination temperature T(o), the response is linear to several percent of the flux quantum energy in the SQUID: the amplifier will be saturated by broad band noise if the noise source temperature is much greater than 10 To; and the array parametric amplifier has the same noise temperature as the single device indicating an N-fold increase in dynamic range. (Author)
User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.
An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.
The authors report a SQUID (superconducting quantum interference device) amplifier with a novel tuning circuit that can be easily coupled to a finite-impedance source. The SQUID amplifier is designed for a source impedance of 50 Omega and a signal frequency of nearly 150 MHz. The performance of the SQUID amplifier has been measured at 4.2 K. The measured gain and noise temperature of the SQUID amplifier are 20 dB and 0.7 K, respectively. A saturation temperature as high as 200 K at the input of the SQUID amplifier is achieved. It is concluded that this type of tuned SQUID amplifier is applicable to the IF (intermediate frequency) amplifier of the SIS (superconductor-insulator-semiconductor) receiver.>