Abstract A series superconducting nanowire single-photon detector is a high performance nanowire array detector that has the potential to reach a high system detection efficiency (SQE), a high counting rate (CR) and photon number resolving functionality. Interconnected with a simplified readout, it shows promise for large scale expansion and has good prospects for future applications in single-photon imaging, quantum optics, quantum computing and deep-space communication. In this paper, we demonstrate a high SQE and CR series superconducting nanowire single-photon detector with an active area of 20 × 20 μ m 2 . The detector shows a maximum SQE of 68% at 1550 nm with a dark count rate of 200 Hz and a wide response wavelength from 1100–2000 nm. It also achieves a CR over 300 MHz at single photon power level and has the capability of resolving photon numbers by up to six photons.
Abstract A series superconducting nanowire single-photon detector is a high performance nanowire array detector that has the potential to reach a high system detection efficiency (SQE), a high counting rate (CR) and photon number resolving functionality. Interconnected with a simplified readout, it shows promise for large scale expansion and has good prospects for future applications in single-photon imaging, quantum optics, quantum computing and deep-space communication. In this paper, we demonstrate a high SQE and CR series superconducting nanowire single-photon detector with an active area of 20 × 20 μ m 2 . The detector shows a maximum SQE of 68% at 1550 nm with a dark count rate of 200 Hz and a wide response wavelength from 1100–2000 nm. It also achieves a CR over 300 MHz at single photon power level and has the capability of resolving photon numbers by up to six photons.
Abstract Count rate (CR) is one of the key parameters of superconducting nanowire single-photon detectors (SNSPDs). The practical SNSPDs usually have a CR of a few MHz to a few tens of MHz owing to the large kinetic inductance originating from the long nanowire, which is necessary for effectively coupling the photons. A feasible approach to decrease the kinetic inductance and consequently increase the detection speed is to replace a long single nanowire with multiple individual nanowires in an array. In this study, we report an SNSPD of nine interleaved nanowires with 70% system detection efficiency (SDE) and 200 Hz dark count rate at the low-photon-flux limit of 1550 nm. Owing to the small dead time (<6 ns) of each nanowire, the SNSPD achieved a maximum CR of 0.93 GHz at a photon flux of 1.26 × 10 10 photons s −1 with an SDE of ∼7.4%, and a CR of 200 MHz with an SDE of over 50%. Furthermore, a photon number resolvability of up to nine photons was also demonstrated.
Photon-number-resolving (PNR) is an important functionality in many applications. The traditional single photon detectors (SNSPDs) operated with the conventional readout scheme does not have the PNR functionality. In this paper, we demonstrate a superconducting photon-number-resolving detector operating at the visible wavelength regime, based on the serial connection of six superconducting nanowires. The results of our 6-element PNR device show clear evidence of n-photons differentiation with n ranging from 1 to 6. The system detection efficiency reaches 54% with the dark counts rate below 10 Hz at 660 nm. The demonstrated 6-element PNR device does not require a complex readout circuit compared with the SNSPD array device, and is expected to have wider applications in addition to imaging and communication.
High Resolution Image Download MS PowerPoint Slide Efficiently distinguishing photon numbers is a crucial yet challenging technology for various quantum information and quantum metrology applications. While superconducting transition edge sensors offer good photon-number-resolving (PNR) capabilities, they are hampered by low detection speed, timing jitter, and complex cooling and readout requirements. In this work, we present a significant advancement toward achieving high-fidelity PNR single-photon detectors by combing high efficiency superconducting nanowire single-photon detector and spatial multiplexing technology. The unique twin-layer configuration of superconducting nanowire atop a dielectric mirror ensures the near-unity detection efficiency. The segmented design, where each section is shunted by a resistor, enables spatial multiplexing, establishing a mapping relationship between pulse amplitude and registered photons. The fabricated detector exhibits impressive performance metrics, including a single-photon system detection efficiency (SDE) of ∼98% at a dark count rate of 20 cps and photon-number resolution capability up to 32. Further characterization through detector tomography reveals high fidelities for two-, three-, and four-photon events, approximately 87%, 73%, and 40% respectively. Moreover, the detector operates at a high count rate of 41 MHz at 3 dB-SDE, with a low timing jitter of as low as 40 ps. With its near-unity efficiency, high photon-number resolution, low dark count rate, fast detection speed, and superior timing resolution, we expect significant interest in these detectors, promising substantial benefits for weak light detection and optical quantum information applications.
Superconducting series nanowire single-photon detectors (SNDs) have been used for resolving photon numbers. But it can also exhibit a higher counting rate than a single superconducting nanowire single-photon detector (SNSPD), because the serial architecture allows multiple detectors working in parallel and the inductance of each pixel is reduced. In this paper, we found each pixel of the SND could reset fast although the whole detector took a much longer time for recovering. Therefore, the speed of an SND with a large kinetic inductance of 1.25 μH was characterized and compared to a standard SNSPD with the same total inductance. By measuring the detected photon rate over the input photon rate, we obtained a photon counting rate enhancement by 7.5 times. Meanwhile, the timing jitter of the SND was 63 ps at single photon detection regime. Our results show that the series structure and the readout scheme are quite practical in realizing high speed single-photon detectors besides resolving photon numbers.
Superconducting nanowire single-photon detectors are a key technology for quantum information and science due to their high efficiency, low timing jitter, and low dark counts. In this work, we present a detector for single 1550 nm photons with up to 78% detection efficiency, timing jitter below 50 ps FWHM, 158 counts/s dark count rate, as well as a maximum count rate of 1.5 giga-counts/s at 3 dB compression. The PEACOQ detector (Performance-Enhanced Array for Counting Optical Quanta) comprises a linear array of 32 straight superconducting niobium nitride nanowires that span the mode of an optical fiber. This design supports high count rates with minimal penalties for detection efficiency and timing jitter. We show how these trade-offs can be mitigated by implementing independent readout for each nanowire and by using a temporal walk correction technique to reduce count-rate dependent timing jitter. These detectors make quantum communication practical on a 10 GHz clock.
Superconducting Nanowire Single Photon Detectors (SNSPDs) excel at a wide variety of performance criteria for single photon counting. They combine unprecedented high detection efficiency, high timing resolution, high count rates, low intrinsic dark count rates, and are sensitive to ultraviolet through mid-infrared single-photons. At JPL, we are working on several projects to push the performance limits of SNSPDs to achieve higher maximum count rates, larger active areas, higher timing resolution, and a wider spectral range. Our recent advances enable new applications for dark matter detection, imaging, and space-to-ground communication and provide insight into the fundamental physics of single-photon detection in superconducting nanowires.