We have demonstrated the multiplexed operation of titanium hot-electron nanobolometers (nano-HEB). Because of their low thermal conductance and small electron heat capacity nanobolometers are particularly interesting as sensors for far- infrared spectroscopy and mid- and near-IR calorimetry. However, the short time constant of these devices (~ µs at 300- 400 mK) makes time domain or audio-frequency domain multiplexing impractical. The Microwave SQUID (MSQUID) approach pursued in this work uses dc SQUIDs coupled to GHz-band microresonators which are, in turn, coupled to a transmission line. We used a 4-element array of Ti HEBs operated at 415 mK in a He3 dewar with an optical fiber access. The microwave signal exhibited 10-MHz wide resonances at individual MSQUD frequencies between 9 GHz and 10 GHz. The resonance depth is modulated by the current through the bolometer via a change of the SQUID flux state. The transmitted signal was amplified by a cryogenic amplifier and downconverted to baseband using an IQ mixer. A 1-dB per Φ 0 /2 responsivity was sufficient for keeping the system noise at the level of ~ 2 pA/Hz 1/2 . This is more than an order of magnitude smaller than phonon noise in the HEB. The devices were able to detect single near-IR photons (1550 nm) with a time constant of 3.5 µs. A digital transceiver for simultaneous generation of 16 probing tones and for processing of 16 downconverting signals has been demonstrated as well.
We have demonstrated the multiplexed operation of titanium hot-electron nanobolometers (nano-HEB). Because of their low thermal conductance and small electron heat capacity nanobolometers are particularly interesting as sensors for far- infrared spectroscopy and mid- and near-IR calorimetry. However, the short time constant of these devices (~ µs at 300- 400 mK) makes time domain or audio-frequency domain multiplexing impractical. The Microwave SQUID (MSQUID) approach pursued in this work uses dc SQUIDs coupled to GHz-band microresonators which are, in turn, coupled to a transmission line. We used a 4-element array of Ti HEBs operated at 415 mK in a He3 dewar with an optical fiber access. The microwave signal exhibited 10-MHz wide resonances at individual MSQUD frequencies between 9 GHz and 10 GHz. The resonance depth is modulated by the current through the bolometer via a change of the SQUID flux state. The transmitted signal was amplified by a cryogenic amplifier and downconverted to baseband using an IQ mixer. A 1-dB per Φ 0 /2 responsivity was sufficient for keeping the system noise at the level of ~ 2 pA/Hz 1/2 . This is more than an order of magnitude smaller than phonon noise in the HEB. The devices were able to detect single near-IR photons (1550 nm) with a time constant of 3.5 µs. A digital transceiver for simultaneous generation of 16 probing tones and for processing of 16 downconverting signals has been demonstrated as well.
We have obtained the first data on the multiplexed operation of titanium hot‐electron bolometers (HEB). Because of their low thermal conductance and small electron heat capacity nanobolometers are particularly interesting as sensors for far‐infrared spectroscopy and mid‐ and near‐IR calorimetry. However, the short time constant of these devices (∼μs at 300–400 mK) makes time domain or audio‐frequency domain multiplexing impractical. The Microwave SQUID (MSQUID) approach pursued in this work uses dc SQUIDs coupled to X‐band microresonators which are, in turn, coupled to a transmission line. We used a 4‐element array of Ti HEBs operated at 415 mK in a He3 dewar with an optical fiber access. The microwave signal exhibited 10‐MHz wide resonances at individual MSQUD frequencies between 9 GHz and 10 GHz. The resonance depth is modulated by the current through the bolometer via a change of the SQUID flux state. The transmitted signal was amplified by a cryogenic amplifier and downconverted to baseband using an IQ mixer. A 1‐dB per Ω0/2 responsivity was sufficient for keeping the system noise at the level of ∼2 pA/Hz1/2. This is more than an order of magnitude smaller than phonon noise in the HEB. The devices were able to detect single near‐IR photons (1550 nm) with a time constant of 3.5 μs. Follow‐on work will scale the array to larger size and will address the microwave frequency signal generation and processing using a digital transceiver.
We are developing hot-electron superconducting transition-edge sensors (TES) capable of counting THz photons and operating at . We fabricated superconducting Ti nanosensors with Nb contacts with a volume of on planar Si substrates and have measured the thermal conductance in the material, G=4times10-3W/K at 0.3 K, caused predominantly by the weak electron-phonon coupling. The corresponding phonon-noise NEP=3times10-19W/Hz1/2. Detection of single optical photons (1550 nm and 670 nm wavelength) has been demonstrated for larger devices and yielded the thermal time constants of 30 mus at 145 mK and of 25 mus at 190 mK. This hot-electron direct detector (HEDD) is expected to have a small enough energy fluctuation noise for detecting individual photons with v>THz where NEP~3times10-20W/Hz1/2is needed for spectroscopy in space.
Superconducting Hot Electron Bolometers (HEBs) are good candidates for detecting weak signals in the submillimeter or terahertz range. In this thesis work, a novel fabrication method was developed to make two types of niobium HEBs for different applications. HEBs were designed, fabricated, and then characterized at dc, microwave, and THz frequencies. The first type is a diffusion-cooled HEB, made with a short bridge that determines its cooling time. In this thesis, bridges were typically 400 nm long with bandwidths of about 1 GHz. These diffusion-cooled HEBs were developed as part of a collaboration with the University of Arizona (UA), to develop a proof-of-concept heterodyne array submillimeter camera. Devices were fabricated on thin fused quartz and silica substrates for waveguide coupling in the UA system for the astrophysically interesting 345 and 810 GHz atmospheric windows. The goal of this collaboration is to provide a basis of comparison between Nb diffusion-cooled HEB mixers and superconductorinsulator-superconductor mixers at these frequencies. The second type is a phonon-cooled HEB, made with a ∼3 µm long bridge. Its thermal response is dictated by the electron-phonon relaxation time. These devices were developed in collaboration with Prof. C. Schmuttenmaer’s lab in the Yale Chemistry department, Prof. G. Blake at Caltech,
We propose a new detection technique based on radio-frequency (RF) bias and readout of an antenna-coupled superconducting nanobolometer. This approach is suitable for Frequency-Division-Multiplexing (FDM) readout of large arrays using broadband low-noise RF amplifier. We call this new detector RFTES. This feasibility study was made on demonstrator devices which are made in all-Nb technology and operate at 4.2 K. The studied RFTES devices consist of an antenna-coupled superconducting nanobolometer made of ultrathin niobium films with transition temperature Tc = 5.2 K. The 0.65-THz antenna and nanobolometer are embedded as a load into a GHz-range coplanar niobium resonator (Tc = 8.9 K, Q = 4000). To heat the superconducting Nb nanobolometer close to the Tc, the RF power at resonator frequency f = 5.8 GHz is applied via a transmission line which is weakly coupled (-11 dB) to the loaded resonator. The THz-antenna of RFTES was placed in the focus of a sapphire immersion lens inside a He4-cryostat equipped with an optical window and a semiconductor RF amplifier. We have demonstrated optical response of the RFTES to THz radiation. The demonstrator receiver system employing the RFTES device showed an optical Noise-Equivalent Power (NEP) 1e-14 W/sqrt(Hz) at 4.2 K.
Dissipationless microwave radio frequency superconducting interference device (RF-SQUID) multiplexers are attractive for readouts of large format arrays of transition edge sensors (TES). This multiplexer has the potential for readout bandwidth of several GHz and power consumption of ≈0.1 pW per pixel, which are ≈103 and ≈10-4 times as large as those of DC-SQUID-based conventional multiplexers. To evaluate their readout performance for TES photon counters ranging from near infrared to gamma ray, white noise of this multiplexer was experimentally studied at 4 K. The reason for this was, firstly, to avoid the low-frequency fluctuation obvious at around 0.1 K but trivial for the energy resolution of photon counters, and secondly for a feasibility study of readout operation at 4 K for extended applications. To increase resonant Q at 4 K and maintain low-noise SQUID operation, multiplexer chips consisting of niobium nitride (NbN)-based coplanar-waveguide resonators and niobium (Nb)-based RF-SQUIDs have been developed. This hybrid multiplexer exhibited 1×104≤QI≤2×104 and the square root of spectral density of current noise referred to the SQUID input √SI =31 pA/√Hz, where QI is the internal Q of resonators. The former and the latter are factor-of-five and seven improvements from our previous results on Nb-based resonators, respectively. Systematic noise measurement with various microwave readout power PMR and two-directional readout on the complex plane of transmission component of scattering matrix S21 makes the contribution of each noise source obvious. By decreasing these noises to the degree achievable by current technology, we predicted the microwave RF-SQUID multiplexer would exhibit √SI ≤5 pA/√Hz; i.e., close to √SI of state-of-the-art DC-SQUID-based multiplexers.
Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.