Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Internet of Things Journal

Exploiting Mapping Diversity for Enhancing Security at Physical Layer in the Internet of Things

Sasi Vinay Pechetti, Abhishek Jindal, Ranjan Bose

Published May 30, 2018• 23 citations
Publisher

Abstract

Application of Internet of Things (IoT) in health, defense, banking, and other confidential information transfer urges the need for secure IoT. As most of the IoT devices are resource-limited (antennas, bandwidth, energy), securing the information transfer has always been a challenge. Looking at a solution for enhancing the security of single antenna, single carrier, energy efficient devices, we propose a novel scheme, channel-based mapping diversity. This scheme uses the inherent randomness of the wireless channel and multiple mappings available for an M-ary phase shift keying constellation in confusing an eavesdropper. When the legitimate and the eavesdropper channels are independent of each other, it is shown that a symbol error rate (SER) of (M-1)/ M is induced at the eavesdropper. Whereas, when the channels are correlated, optimal and suboptimal strategies at source and eavesdropper are derived for their respective optimal performances. Further, a closed-form expression for a lower-bound on the SER at the eavesdropper is derived. Simulation results show that for the correlated case, as SNR at the eavesdropper increases, SER initially decreases, later saturates to a relatively high SER, hence making the job of the eavesdropper difficult in getting the legitimate data. Furthermore, the effect of the correlation is more pronounced on SER at higher levels of correlation. This indicates that for practical correlation scenarios, SER is high enough to confuse the eavesdropper.

DOI
10.1109/jiot.2018.2842056

Related papers

Channel-based mapping diversity for enhancing the physical layer security in the Internet of Things

Sasi Vinay Pechetti, Abhishek Jindal, Ranjan Bose

Demand of minimal hardware requirement and low energy consumption for internet of things (IoT) has gained the importance of techniques enhancing the physical layer security. Looking at this, we propose a channel-based mapping diversity (CBMD) scheme for a source (S), destination (D) pair to increase the average bit error rate (ABER) at an eavesdropper (E). CBMD leads to an ABER of 0.5 at E when the channels between S - D and S - E are independent. In the case where S - D and S - E are correlated (due to the proximity of E at D), we derive an optimal strategy at E which leads to the best performance at E. We also derive an optimal strategy at S, assuming E uses its optimal strategy, thereby, considering the worst case scenario. A sub-optimal strategy is also proposed at S which does not require any statistical information about the link S - E and hence, has low implementation complexity. We analyze the variation of ABER at E with the signal to noise ratio (SNR) and the channel correlation coefficient. Our simulation results demonstrate that CBMD indeed leads to significant performance degradation at E even at moderate channel correlation for a properly chosen strategy.

IEEE International Symposium on Personal, Indoor and Mobile Radio Communications (PIMRC)•Oct 1, 2017•10 citations

A Channel State Information-Based Key Generation Scheme for Internet of Things

Muhammad Usman, Saud Althunibat, Marwa Qaraqe

Internet-of-Things (IoT) networks generally contain resource-constrained devices that require an energy-efficient key generation procedure to producing secure keys at a faster rate. The physical characteristics of the wireless channel can be exploited to secure communication within IoT networks. In particular, secret keys can be generated by leveraging on the randomness of the wireless physical channel between two communicating parties. The conventional mechanism of generating keys at the physical layer, i.e., using channel probing, quantization, information reconciliation, and privacy amplification, may not be preferable for IoT devices. In addition, in some cases IoT devices may be deployed in static environments, wherein the channel coherence time is too high to generate keys at a faster rate and with the desired randomness. This study proposes a mapping table-based key distribution scheme for IoT environments, wherein multiple characteristics of the random channel are combined to improve not only the key generation rate (KGR) but also the key agreement rate (KAR) and bit error rate (BER). In the proposed scheme, both the channel magnitude and the phase are exploited in the key generation process. The proposed scheme is immune to channel estimation errors while providing sufficient randomness in the static environment. Additionally, the scheme is thoroughly investigated for different scenarios including the case of a smarter eavesdropper, which attempts to estimate the channel between the legitimate nodes. This case verifies the robustness of the proposed scheme in different settings and attack models.

Security and Communication Networks•May 14, 2022•16 citations

Time Reversal Precoding with Artificial Noise Injection for Physical Layer Security

Sidney Golstein

An increasing number of devices exchanges data via the wireless medium into large scale, decentralized, and heterogeneous networks, leading to the concept of Internet of Things (IoT). This PhD work proposes a new practical scheme to perform physical layer security (PLS) in this IoT context.Wireless communications in IoT networks are prone to passive eavesdropping. Therefore, this work introduces a scheme that guarantees the reliability of a communication from a transmitter (Alice) towards a legitimate user (Bob), while preventing multiple passive eavesdroppers (Eve) to correctly decode the data in a worst-cases scenario, thereby considering i) Eve to be noiseless, ii) Eve equipped with an arbitrarily large number of antennas, iii) Alice imperfectly estimating Bob's channel state information (CSI). To do so, a frequency domain time-reversal (TR) precoder is proposed using orthogonal frequency-division multiplexing (OFDM) and artificial noise (AN) injection. The scheme exploits the frequency diversity selective behaviour in multipath channels, and can be incorporated into existing standards, such as in LTE or 5G networks. Different configurations are investigated, namely, single-input single-output (SISO), multiple-input single-output (MISO), and single-input multiple-output (SIMO) systems.The handshake procedures between Alice and Bob are described, both in time-division duplexing (TDD) and frequency-division duplexing (FDD) systems, highlighting the amount of CSI acquisition at Eve, which influences the secrecy performances. Depending on the handshake procedures, different decoding structures are investigated at Eve for each system configuration, considering a block-fading environment. Closed-form approximations of the signal-to-noise ratio required at Bob and the maximal CSI error that can be made at Alice, in order to guarantee a communication ergodic secrecy rate (ESR), are derived. Furthermore, the optimal amount of AN energy to inject, as well as the maximal number of eavesdropper's antennas allowed, considering imperfect CSI, are also given as closed-form expressions. A trade-off on the choice of the spreading factor of the TR precoder is established between maximizing the ESR and decreasing the percentage of outage, leading to information leaked to Eve. Finally, thanks to these results, Alice can be a-priori aware of the ESR over which she can establish a secure communication, assuming worst-case assumptions regarding the eavesdroppers. The PLS scheme presented in this PhD work therefore emerges as a promising solution to secure wireless communications in IoT networks.

•Feb 15, 2022•0 citations

Secure Key Distribution Scheme in IoT Networks Exploiting Channel State Information

Tasneem Alshamaseen, Saud Althunibat, Marwa Qaraqe +1 more

The Internet of Things (IoT) is a popular technology that refers to a network of internet-connected physical devices that interact to perform tasks with minimal human intervention. However, as these networks expand, ensuring their security becomes challenging due to the communication broadcasting nature and extensive data exchanges. Traditional cryptographic security methods may not be optimal due to the constrained resources of loT devices. In this study, we propose a novel secure key distribution scheme from a physical layer perspective suitable for an loT environment. The proposed scheme takes advantage of the availability of Channel State Information (CSI) at both ends of the communication to enhance security. Specifically, CSI is utilized to precode the key symbols during the key distribution process. Additionally, the scheme employs the xor operation to add an extra layer of difficulty for potential eavesdroppers that attempt to retrieve the transmitted key symbols. The performance of the proposed scheme is evaluated in terms of Key Error Rate (KER) at legitimate nodes and eavesdroppers by using Monte Carlo simulations.

IEEE Vehicular Technology Conference•Jun 24, 2024•0 citations

Physical-Layer Cooperative Key Generation with Correlated Eavesdropping Channels in IoT

Peng Xu, Dongyang Hu, Gaojie Chen

With a massive amount of wireless sensor nodes in Internet of Things (IoT), it is difficult to establish key distribution and management mechanism for traditional encryption technology. Alternatively, the physical layer key generation technology is promising to implement in IoT, since it is based on the principle of information-theoretical security and has the advantage of low complexity. Most existing key generation schemes assume that eavesdropping channels are independent of legitimate channels, which may not be practical especially when eavesdropper nodes are near to legitimate nodes. However, this paper investigates key generation problems for a multi-relay wireless network in IoT, where the correlation between eavesdropping and legitimate channels are considered. Key generation schemes are proposed for both non-colluding and partially colluding eavesdroppers situations. The main idea is to divide the key agreement process into three phases: 1) we first generate a secret key by exploiting the difference between the random channels associated with each relay node and the eavesdropping channels; 2) another key is generated by integrating the residual common randomness associated with each relay pair; 3) the two keys generated in the first two phases are concatenated into the final key. The secrecy key performance of the proposed key generation schemes is also derived with closed-forms.

IEEE International Conference on Internet of Things (iThings) and IEEE Green Computing and Communications (GreenCom) and IEEE Cyber, Physical and Social Computing (CPSCom) and IEEE Smart Data (SmartData)•Nov 1, 2020•13 citations

A Lightweight Secure and Resilient Transmission Scheme for the Internet of Things in the Presence of a Hostile Jammer

Mehdi Letafati, Ali Kuhestani, Kai‐Kit Wong +1 more

In this article, we propose a lightweight security scheme for ensuring both information confidentiality and transmission resiliency in the Internet-of-Things (IoT) communication. A single-antenna transmitter communicates with a half-duplex single-antenna receiver in the presence of a sophisticated multiple-antenna-aided passive eavesdropper and a multiple-antenna-assisted hostile jammer (HJ). A low-complexity artificial noise (AN) injection scheme is proposed for drowning out the eavesdropper. Furthermore, for enhancing the resilience against HJ attacks, the legitimate nodes exploit their own local observations of the wireless channel as the source of randomness to agree on shared secret keys. The secret key is utilized for the frequency hopping (FH) sequence of the proposed communication system. We then proceed to derive a new closed-form expression for the achievable secret key rate (SKR) and the ergodic secrecy rate (ESR) for characterizing the secrecy benefits of our proposed scheme, in terms of both information secrecy and transmission resiliency. Moreover, the optimal power sharing between the AN and the message signal is investigated with the objective of enhancing the secrecy rate. Finally, through extensive simulations, we demonstrate that our proposed system model outperforms the state-of-the-art transmission schemes in terms of secrecy and resiliency. Several numerical examples and discussions are also provided to offer further engineering insights.

IEEE Internet of Things Journal•Sep 24, 2020•60 citations
Application of Internet of Things (IoT) in health, defense, banking, and other confidential information transfer urges the need for secure IoT. As most of the IoT devices are resource-limited (antennas, bandwidth, energy), securing the information transfer has always been a challenge. Looking at a solution for enhancing the security of single antenna, single carrier, energy efficient devices, we propose a novel scheme, channel-based mapping diversity. This scheme uses the inherent randomness of the wireless channel and multiple mappings available for an M-ary phase shift keying constellation in confusing an eavesdropper. When the legitimate and the eavesdropper channels are independent of each other, it is shown that a symbol error rate (SER) of (M-1)/ M is induced at the eavesdropper. Whereas, when the channels are correlated, optimal and suboptimal strategies at source and eavesdropper are derived for their respective optimal performances. Further, a closed-form expression for a lower-bound on the SER at the eavesdropper is derived. Simulation results show that for the correlated case, as SNR at the eavesdropper increases, SER initially decreases, later saturates to a relatively high SER, hence making the job of the eavesdropper difficult in getting the legitimate data. Furthermore, the effect of the correlation is more pronounced on SER at higher levels of correlation. This indicates that for practical correlation scenarios, SER is high enough to confuse the eavesdropper.
Demand of minimal hardware requirement and low energy consumption for internet of things (IoT) has gained the importance of techniques enhancing the physical layer security. Looking at this, we propose a channel-based mapping diversity (CBMD) scheme for a source (S), destination (D) pair to increase the average bit error rate (ABER) at an eavesdropper (E). CBMD leads to an ABER of 0.5 at E when the channels between S - D and S - E are independent. In the case where S - D and S - E are correlated (due to the proximity of E at D), we derive an optimal strategy at E which leads to the best performance at E. We also derive an optimal strategy at S, assuming E uses its optimal strategy, thereby, considering the worst case scenario. A sub-optimal strategy is also proposed at S which does not require any statistical information about the link S - E and hence, has low implementation complexity. We analyze the variation of ABER at E with the signal to noise ratio (SNR) and the channel correlation coefficient. Our simulation results demonstrate that CBMD indeed leads to significant performance degradation at E even at moderate channel correlation for a properly chosen strategy.
Internet-of-Things (IoT) networks generally contain resource-constrained devices that require an energy-efficient key generation procedure to producing secure keys at a faster rate. The physical characteristics of the wireless channel can be exploited to secure communication within IoT networks. In particular, secret keys can be generated by leveraging on the randomness of the wireless physical channel between two communicating parties. The conventional mechanism of generating keys at the physical layer, i.e., using channel probing, quantization, information reconciliation, and privacy amplification, may not be preferable for IoT devices. In addition, in some cases IoT devices may be deployed in static environments, wherein the channel coherence time is too high to generate keys at a faster rate and with the desired randomness. This study proposes a mapping table-based key distribution scheme for IoT environments, wherein multiple characteristics of the random channel are combined to improve not only the key generation rate (KGR) but also the key agreement rate (KAR) and bit error rate (BER). In the proposed scheme, both the channel magnitude and the phase are exploited in the key generation process. The proposed scheme is immune to channel estimation errors while providing sufficient randomness in the static environment. Additionally, the scheme is thoroughly investigated for different scenarios including the case of a smarter eavesdropper, which attempts to estimate the channel between the legitimate nodes. This case verifies the robustness of the proposed scheme in different settings and attack models.
An increasing number of devices exchanges data via the wireless medium into large scale, decentralized, and heterogeneous networks, leading to the concept of Internet of Things (IoT). This PhD work proposes a new practical scheme to perform physical layer security (PLS) in this IoT context.Wireless communications in IoT networks are prone to passive eavesdropping. Therefore, this work introduces a scheme that guarantees the reliability of a communication from a transmitter (Alice) towards a legitimate user (Bob), while preventing multiple passive eavesdroppers (Eve) to correctly decode the data in a worst-cases scenario, thereby considering i) Eve to be noiseless, ii) Eve equipped with an arbitrarily large number of antennas, iii) Alice imperfectly estimating Bob's channel state information (CSI). To do so, a frequency domain time-reversal (TR) precoder is proposed using orthogonal frequency-division multiplexing (OFDM) and artificial noise (AN) injection. The scheme exploits the frequency diversity selective behaviour in multipath channels, and can be incorporated into existing standards, such as in LTE or 5G networks. Different configurations are investigated, namely, single-input single-output (SISO), multiple-input single-output (MISO), and single-input multiple-output (SIMO) systems.The handshake procedures between Alice and Bob are described, both in time-division duplexing (TDD) and frequency-division duplexing (FDD) systems, highlighting the amount of CSI acquisition at Eve, which influences the secrecy performances. Depending on the handshake procedures, different decoding structures are investigated at Eve for each system configuration, considering a block-fading environment. Closed-form approximations of the signal-to-noise ratio required at Bob and the maximal CSI error that can be made at Alice, in order to guarantee a communication ergodic secrecy rate (ESR), are derived. Furthermore, the optimal amount of AN energy to inject, as well as the maximal number of eavesdropper's antennas allowed, considering imperfect CSI, are also given as closed-form expressions. A trade-off on the choice of the spreading factor of the TR precoder is established between maximizing the ESR and decreasing the percentage of outage, leading to information leaked to Eve. Finally, thanks to these results, Alice can be a-priori aware of the ESR over which she can establish a secure communication, assuming worst-case assumptions regarding the eavesdroppers. The PLS scheme presented in this PhD work therefore emerges as a promising solution to secure wireless communications in IoT networks.
The Internet of Things (IoT) is a popular technology that refers to a network of internet-connected physical devices that interact to perform tasks with minimal human intervention. However, as these networks expand, ensuring their security becomes challenging due to the communication broadcasting nature and extensive data exchanges. Traditional cryptographic security methods may not be optimal due to the constrained resources of loT devices. In this study, we propose a novel secure key distribution scheme from a physical layer perspective suitable for an loT environment. The proposed scheme takes advantage of the availability of Channel State Information (CSI) at both ends of the communication to enhance security. Specifically, CSI is utilized to precode the key symbols during the key distribution process. Additionally, the scheme employs the xor operation to add an extra layer of difficulty for potential eavesdroppers that attempt to retrieve the transmitted key symbols. The performance of the proposed scheme is evaluated in terms of Key Error Rate (KER) at legitimate nodes and eavesdroppers by using Monte Carlo simulations.
With a massive amount of wireless sensor nodes in Internet of Things (IoT), it is difficult to establish key distribution and management mechanism for traditional encryption technology. Alternatively, the physical layer key generation technology is promising to implement in IoT, since it is based on the principle of information-theoretical security and has the advantage of low complexity. Most existing key generation schemes assume that eavesdropping channels are independent of legitimate channels, which may not be practical especially when eavesdropper nodes are near to legitimate nodes. However, this paper investigates key generation problems for a multi-relay wireless network in IoT, where the correlation between eavesdropping and legitimate channels are considered. Key generation schemes are proposed for both non-colluding and partially colluding eavesdroppers situations. The main idea is to divide the key agreement process into three phases: 1) we first generate a secret key by exploiting the difference between the random channels associated with each relay node and the eavesdropping channels; 2) another key is generated by integrating the residual common randomness associated with each relay pair; 3) the two keys generated in the first two phases are concatenated into the final key. The secrecy key performance of the proposed key generation schemes is also derived with closed-forms.
In this article, we propose a lightweight security scheme for ensuring both information confidentiality and transmission resiliency in the Internet-of-Things (IoT) communication. A single-antenna transmitter communicates with a half-duplex single-antenna receiver in the presence of a sophisticated multiple-antenna-aided passive eavesdropper and a multiple-antenna-assisted hostile jammer (HJ). A low-complexity artificial noise (AN) injection scheme is proposed for drowning out the eavesdropper. Furthermore, for enhancing the resilience against HJ attacks, the legitimate nodes exploit their own local observations of the wireless channel as the source of randomness to agree on shared secret keys. The secret key is utilized for the frequency hopping (FH) sequence of the proposed communication system. We then proceed to derive a new closed-form expression for the achievable secret key rate (SKR) and the ergodic secrecy rate (ESR) for characterizing the secrecy benefits of our proposed scheme, in terms of both information secrecy and transmission resiliency. Moreover, the optimal power sharing between the AN and the message signal is investigated with the objective of enhancing the secrecy rate. Finally, through extensive simulations, we demonstrate that our proposed system model outperforms the state-of-the-art transmission schemes in terms of secrecy and resiliency. Several numerical examples and discussions are also provided to offer further engineering insights.