Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Magnetometry by a proximity Josephson junction interferometer

Robab Najafi Jabdaraghi

Published Feb 13, 2018• 0 citations
OpenAlex

Abstract

In quantum technology, several aspects of superconductivity such as proximity effect have studied to develop a wide range of attractive applications at sub-kelvin temperatures. A new type of interferometer based on the proximity effect, taking place around transparent interfaces between normal- and superconducting metals, the Superconducting Quantum Interference Proximity Transistor (SQUIPT), relies on the phase dependence of the density of states in the proximized weak link. The SQUIPT devices offer the possibility to realize sensitive low-dissipation magnetometers compared to conventional DC SQUIDs. In this thesis, we investigate the development of the sensitive SQUIPT magnetometers. The first part of the thesis covers the characterization of non-hysteretic SQUIPTs with enhanced responsivity. In these structures, we demonstrate magnetic flux modulation of the device characteristics displaying no hysteresis at low temperatures by simply increasing the Josephson inductance of the weak link compared to self-inductance of the superconducting loop in the device. As a consequence, improvement in magnetic field responsivity is achievable. We then turn to the implementation of SQUIPT devices based on different fabrication methods and superconductor materials for improving the device performance. In this aspect, we fabricate and characterize niobium-based SNS devices utilizing two separate lithography and deposition steps with strong Ar ion cleaning in between. We further investigate a prototype hybrid SQUIPT device based on an Nb-Cu-Nb SNS junction with a conventional Al probe in tunnel junction. In the third part of the thesis, we present the flux noise characterization of a SQUIPT device using simultaneous measurement of DC transport properties and shot noise. To probe the noise, we use a cryogenic amplifier operating at frequencies in the range of a few MHz. We adapt this technique for flux noise measurements in SQUIPTs, adaptable also to low-temperature shot noise measurements of other nonlinear devices with high impedance. In order to investigate flux noise of SQUIPTs, we develop a model allowing one to optimize the figures of merit of the magnetometers such as the noise-equivalent flux.

Related papers

Magnetometry by a proximity Josephson junction interferometer

Robab Najafi Jabdaraghi

In quantum technology, several aspects of superconductivity such as proximity effect have studied to develop a wide range of attractive applications at sub-kelvin temperatures. A new type of interferometer based on the proximity effect, taking place around transparent interfaces between normal- and superconducting metals, the Superconducting Quantum Interference Proximity Transistor (SQUIPT), relies on the phase dependence of the density of states in the proximized weak link. The SQUIPT devices offer the possibility to realize sensitive low-dissipation magnetometers compared to conventional DC SQUIDs. In this thesis, we investigate the development of the sensitive SQUIPT magnetometers. \n \nThe first part of the thesis covers the characterization of non-hysteretic SQUIPTs with enhanced responsivity. In these structures, we demonstrate magnetic flux modulation of the device characteristics displaying no hysteresis at low temperatures by simply increasing the Josephson inductance of the weak link compared to self-inductance of the superconducting loop in the device. As a consequence, improvement in magnetic field responsivity is achievable. \n \nWe then turn to the implementation of SQUIPT devices based on different fabrication methods and superconductor materials for improving the device performance. In this aspect, we fabricate and characterize niobium-based SNS devices utilizing two separate lithography and deposition steps with strong Ar ion cleaning in between. We further investigate a prototype hybrid SQUIPT device based on an Nb-Cu-Nb SNS junction with a conventional Al probe in tunnel junction. \n \nIn the third part of the thesis, we present the flux noise characterization of a SQUIPT device using simultaneous measurement of DC transport properties and shot noise. To probe the noise, we use a cryogenic amplifier operating at frequencies in the range of a few MHz. We adapt this technique for flux noise measurements in SQUIPTs, adaptable also to low-temperature shot noise measurements of other nonlinear devices with high impedance. In order to investigate flux noise of SQUIPTs, we develop a model allowing one to optimize the figures of merit of the magnetometers such as the noise-equivalent flux.

•Jan 1, 2018•3 citations

Noise of a superconducting magnetic flux sensor based on a proximity Josephson junction

Robab Najafi Jabdaraghi, Dmitry S. Golubev, Jukka P Pekola +1 more

Abstract We demonstrate simultaneous measurements of DC transport properties and flux noise of a hybrid superconducting magnetometer based on the proximity effect (superconducting quantum interference proximity transistor, SQUIPT). The noise is probed by a cryogenic amplifier operating in the frequency range of a few MHz. In our non-optimized device, we achieve minimum flux noise ~4 μ Φ 0 /Hz 1/2 , set by the shot noise of the probe tunnel junction. The flux noise performance can be improved by further optimization of the SQUIPT parameters, primarily minimization of the proximity junction length and cross section. Furthermore, the experiment demonstrates that the setup can be used to investigate shot noise in other nonlinear devices with high impedance. This technique opens the opportunity to measure sensitive magnetometers including SQUIPT devices with very low dissipation.

arXiv:1705.06448•Scientific Reports•Aug 8, 2017•15 citations

Non-hysteretic superconducting quantum interference proximity transistor with enhanced responsivity

Robab Najafi Jabdaraghi, M. Meschke, Jukka P Pekola

This letter presents fabrication and characterization of an optimized SQUIPT (superconducting quantum interference proximity transistor). The present device, characterized with reduced tunnel junction area and shortened normal-metal section, demonstrates no hysteresis at low temperatures as we increased the Josephson inductance of the weak link by decreasing its cross section. It has consequently almost an order of magnitude improved magnetic field responsivity as compared to the earlier design. The modulation of both the current and the voltage across the junction have been measured as a function of magnetic flux piercing the superconducting loop.

arXiv:1310.8085•Applied Physics Letters•Feb 24, 2014•19 citations

Inductive Superconducting Quantum Interference Proximity Transistor: The L-SQUIPT

Federico Paolucci, Paolo Solinas, Francesco Giazotto

The design for an inductive superconducting quantum interference proximity transistor with enhanced performance, the L-SQUIPT, is presented and analyzed. The interferometer is based on a double-loop structure, where each ring comprises a superconductor--normal-metal--superconductor mesoscopic Josephson weak link and the readout electrode is implemented in the form of a superconducting tunnel probe. Our design allows us to both improve the coupling of the transistor to the external magnetic field and increase the characteristic magnetic flux transfer functions, thereby leading to an improved ultrasensitive quantum limited magnetometer. The L-SQUIPT behavior is analyzed in both the dissipative and the dissipationless Josephson-like operation modes, in the latter case by exploiting both an inductive and a dispersive readout scheme. The improved performance makes the L-SQUIPT promising for magnetic flux detection as well as for specific applications in quantum technology, where a responsive dispersive magnetometry at millikelvin temperatures is required.

arXiv:2203.03948•Physical Review Applied•Nov 15, 2022•4 citations

Spectral Characteristics of a Fully Superconducting SQUIPT

Pauli Virtanen, Alberto Ronzani, F. Giazotto

Superconducting loops form a basis for very sensitive magnetometers. Recently, replacing the Josephson junction of a SQUID with a weak link, and probing the flux by measuring tunneling current, was proposed to realize a SQUIPT (superconducting quantum interference proximity transistor) sensor. Here the authors theorize an all-superconducting variant of this design, which would permit simplified fabrication of a device from a single material.

arXiv:1607.04414•Physical Review Applied•Nov 7, 2016•21 citations

Ultralinear Magnetic-Flux-To-Voltage Conversion in Superconducting Quantum Interference Proximity Transistors

Giorgio De Simoni, Francesco Giazotto

Superconducting interferometers are quantum devices able to transduce a magnetic flux into an electrical output with excellent sensitivity, integrability, and power consumption. Yet, their voltage response is intrinsically nonlinear, a limitation which is conventionally circumvented through the introduction of compensation inductances or by the construction of complex device arrays. Here we propose an intrinsically linear flux-to-voltage mesoscopic transducer, exploiting the superconducting quantum interference proximity transistor (SQUIPT) as a fundamental building block, called bi-SQUIPT. It provides a voltage-noise spectral density as low as approximately ${10}^{\ensuremath{-}16}\phantom{\rule{0.2em}{0ex}}{\mathrm{V}/\mathrm{Hz}}^{1/2}$ and, more interestingly, under a proper operation parameter selection, exhibits a spur-free dynamic range as large as approximately $60$ dB, a value on par with that obtained with state-of-the-art linear flux-to-voltage superconducting transducers based on superconducting quantum interference devices (SQUIDs). Furthermore, thanks to its peculiar measurement configuration, the bi-SQUIPT is tolerant to imperfections and nonidealities in general. For the above reasons, we believe that the bi-SQUIPT could provide a relevant step beyond in the field of low-dissipation and low-noise current amplification with a special emphasis on applications in cryogenic quantum electronics.

arXiv:2207.00339•Physical Review Applied•May 5, 2023•5 citations
In quantum technology, several aspects of superconductivity such as proximity effect have studied to develop a wide range of attractive applications at sub-kelvin temperatures. A new type of interferometer based on the proximity effect, taking place around transparent interfaces between normal- and superconducting metals, the Superconducting Quantum Interference Proximity Transistor (SQUIPT), relies on the phase dependence of the density of states in the proximized weak link. The SQUIPT devices offer the possibility to realize sensitive low-dissipation magnetometers compared to conventional DC SQUIDs. In this thesis, we investigate the development of the sensitive SQUIPT magnetometers.
The first part of the thesis covers the characterization of non-hysteretic SQUIPTs with enhanced responsivity. In these structures, we demonstrate magnetic flux modulation of the device characteristics displaying no hysteresis at low temperatures by simply increasing the Josephson inductance of the weak link compared to self-inductance of the superconducting loop in the device. As a consequence, improvement in magnetic field responsivity is achievable.
We then turn to the implementation of SQUIPT devices based on different fabrication methods and superconductor materials for improving the device performance. In this aspect, we fabricate and characterize niobium-based SNS devices utilizing two separate lithography and deposition steps with strong Ar ion cleaning in between. We further investigate a prototype hybrid SQUIPT device based on an Nb-Cu-Nb SNS junction with a conventional Al probe in tunnel junction.
In the third part of the thesis, we present the flux noise characterization of a SQUIPT device using simultaneous measurement of DC transport properties and shot noise. To probe the noise, we use a cryogenic amplifier operating at frequencies in the range of a few MHz. We adapt this technique for flux noise measurements in SQUIPTs, adaptable also to low-temperature shot noise measurements of other nonlinear devices with high impedance. In order to investigate flux noise of SQUIPTs, we develop a model allowing one to optimize the figures of merit of the magnetometers such as the noise-equivalent flux.
In quantum technology, several aspects of superconductivity such as proximity effect have studied to develop a wide range of attractive applications at sub-kelvin temperatures. A new type of interferometer based on the proximity effect, taking place around transparent interfaces between normal- and superconducting metals, the Superconducting Quantum Interference Proximity Transistor (SQUIPT), relies on the phase dependence of the density of states in the proximized weak link. The SQUIPT devices offer the possibility to realize sensitive low-dissipation magnetometers compared to conventional DC SQUIDs. In this thesis, we investigate the development of the sensitive SQUIPT magnetometers. \n \nThe first part of the thesis covers the characterization of non-hysteretic SQUIPTs with enhanced responsivity. In these structures, we demonstrate magnetic flux modulation of the device characteristics displaying no hysteresis at low temperatures by simply increasing the Josephson inductance of the weak link compared to self-inductance of the superconducting loop in the device. As a consequence, improvement in magnetic field responsivity is achievable. \n \nWe then turn to the implementation of SQUIPT devices based on different fabrication methods and superconductor materials for improving the device performance. In this aspect, we fabricate and characterize niobium-based SNS devices utilizing two separate lithography and deposition steps with strong Ar ion cleaning in between. We further investigate a prototype hybrid SQUIPT device based on an Nb-Cu-Nb SNS junction with a conventional Al probe in tunnel junction. \n \nIn the third part of the thesis, we present the flux noise characterization of a SQUIPT device using simultaneous measurement of DC transport properties and shot noise. To probe the noise, we use a cryogenic amplifier operating at frequencies in the range of a few MHz. We adapt this technique for flux noise measurements in SQUIPTs, adaptable also to low-temperature shot noise measurements of other nonlinear devices with high impedance. In order to investigate flux noise of SQUIPTs, we develop a model allowing one to optimize the figures of merit of the magnetometers such as the noise-equivalent flux.
Abstract We demonstrate simultaneous measurements of DC transport properties and flux noise of a hybrid superconducting magnetometer based on the proximity effect (superconducting quantum interference proximity transistor, SQUIPT). The noise is probed by a cryogenic amplifier operating in the frequency range of a few MHz. In our non-optimized device, we achieve minimum flux noise ~4 μ Φ 0 /Hz 1/2 , set by the shot noise of the probe tunnel junction. The flux noise performance can be improved by further optimization of the SQUIPT parameters, primarily minimization of the proximity junction length and cross section. Furthermore, the experiment demonstrates that the setup can be used to investigate shot noise in other nonlinear devices with high impedance. This technique opens the opportunity to measure sensitive magnetometers including SQUIPT devices with very low dissipation.
This letter presents fabrication and characterization of an optimized SQUIPT (superconducting quantum interference proximity transistor). The present device, characterized with reduced tunnel junction area and shortened normal-metal section, demonstrates no hysteresis at low temperatures as we increased the Josephson inductance of the weak link by decreasing its cross section. It has consequently almost an order of magnitude improved magnetic field responsivity as compared to the earlier design. The modulation of both the current and the voltage across the junction have been measured as a function of magnetic flux piercing the superconducting loop.
The design for an inductive superconducting quantum interference proximity transistor with enhanced performance, the L-SQUIPT, is presented and analyzed. The interferometer is based on a double-loop structure, where each ring comprises a superconductor--normal-metal--superconductor mesoscopic Josephson weak link and the readout electrode is implemented in the form of a superconducting tunnel probe. Our design allows us to both improve the coupling of the transistor to the external magnetic field and increase the characteristic magnetic flux transfer functions, thereby leading to an improved ultrasensitive quantum limited magnetometer. The L-SQUIPT behavior is analyzed in both the dissipative and the dissipationless Josephson-like operation modes, in the latter case by exploiting both an inductive and a dispersive readout scheme. The improved performance makes the L-SQUIPT promising for magnetic flux detection as well as for specific applications in quantum technology, where a responsive dispersive magnetometry at millikelvin temperatures is required.
Superconducting interferometers are quantum devices able to transduce a magnetic flux into an electrical output with excellent sensitivity, integrability, and power consumption. Yet, their voltage response is intrinsically nonlinear, a limitation which is conventionally circumvented through the introduction of compensation inductances or by the construction of complex device arrays. Here we propose an intrinsically linear flux-to-voltage mesoscopic transducer, exploiting the superconducting quantum interference proximity transistor (SQUIPT) as a fundamental building block, called bi-SQUIPT. It provides a voltage-noise spectral density as low as approximately ${10}^{\ensuremath{-}16}\phantom{\rule{0.2em}{0ex}}{\mathrm{V}/\mathrm{Hz}}^{1/2}$ and, more interestingly, under a proper operation parameter selection, exhibits a spur-free dynamic range as large as approximately 606060 dB, a value on par with that obtained with state-of-the-art linear flux-to-voltage superconducting transducers based on superconducting quantum interference devices (SQUIDs). Furthermore, thanks to its peculiar measurement configuration, the bi-SQUIPT is tolerant to imperfections and nonidealities in general. For the above reasons, we believe that the bi-SQUIPT could provide a relevant step beyond in the field of low-dissipation and low-noise current amplification with a special emphasis on applications in cryogenic quantum electronics.