An Integrated Optical-Waveguide Chip for Measurement of Cold-Atom Clouds

Manuel Succo

Published Feb 1, 2011• 2 citations

Abstract

This thesis introduces the first demonstration of a monolithic, micro-fabricated, multi-channel, optical-waveguide chip to measure ultra-cold atomic clouds. The optics consist of an array of 12 independent junctions, which are separated by only 10 μm and have large atom-photon coupling. The integrated and scalable design is presented, along with an atom chip for mounting the optical waveguide chip and magnetically trapping and handling ultra-cold atoms. The experimental apparatus which was built to accommodate this new chip set is described, along with a new experimental control programme which was developed to accommodate the scalability requirements of the new chip. The chip was optically, mechanically and magnetically characterised and cold atoms with densities up to 10-² μm-³, corresponding to 1 atom at a time inside the waveguide mode, were detected with this new kind of chip using absorption and fluorescence techniques. Subsequently, the atoms were utilised to diagnose light polarisation and intensity within the optical-waveguide chip. For future use, various detection methods adapted to the optical-waveguide chip were considered to minimise photon scattering and thus heating of a trapped ultra-cold sample of atoms.

DOI: 10.25560/6394

Related papers

Detecting Atoms with Integrated Optics and Frequency-Synthesised Light

M. Kohnen

This thesis reports on the development of novel techniques for the detection and manipulation of cold gases of neutral atoms. The research presented focusses on the implementation of a photonic waveguide chip into an atom optics experiment. Our photonic chip consists of 12 parallel waveguides with a 10 µm pitch and a 16 µm trench in the centre. A wire subchip underneath the photonic chip can create magnetic fields to guide atoms into the trench and hold them there. The electric field of the light mode propagating through the waveguides has a 1/e radius of 2:2 µm. This small light mode can readily be used for local measurements of the atomic density. This thesis describes the setup of the waveguide chip experiment and gives a detailed characterisation of the interaction between light and atoms in the trench. Additionally, I report on a scheme for detecting atoms while minimising the number of scattered photons for a given precision of the measurement. We use a light beam synthesized from two frequencies tuned to either side of the atomic resonance and detect the differential phase shift they acquire when passing through an atomic cloud by referencing the beat between the two frequencies to a local oscillator. Unlike most similar techniques our beam does not contain a carrier signal and can therefore be balanced around the atomic resonance in order to cancel the mean optical dipole force on the atoms.

Nov 1, 20121 citation

Measurement and manipulation of ultracold bosons using microfabricated optics

James Garvie-Cook

This thesis describes atomic physics experiments performed using a microfabricated photonic waveguide chip: a device that enables the interaction of cold atoms with an array of 12 microscopic light beams emitted by optical waveguides, inside a microscopic trench that has been cut into the chip, across all of the waveguides. The chip uses standard cold-atom control techniques along with readily available photonics technologies to provide an integrated atomic physics device that is not ‘scalable’ so much as already scaled. We describe experiments where atoms are driven into the trench using magneto-optical traps and magnetic traps. In the latter case, the large, homogeneous magnetic field that is present during the atom-light interaction allows us to observe polarization-dependent effects in absorption signals from the trench. Vacuum difficulties have limited the efficiency of rf-driven evaporative cooling in our magnetic trap to 0.4 (with a final phase-space density of 2×10^-5). To circumvent this issue, we have developed a novel evaporative cooling process, in which a dimple potential, comprised of an optical trap and a magnetic trap, is used to perform cycles of isentropic trap deformation and selective atom removal. Using this cooling process increases our evaporative cooling efficiency to 1.2. Various other cooling strategies that involve the dimple are also investigated. Using the dimple, we achieve a phase-space density of 0.04. Having cooled the cloud using the dimple, we move it into the trench and measure absorption signals of 50%, much larger than those achieved previously. We investigate the possibility of producing microscopic optical dipole traps in the trench by sending red-detuned light through the waveguides, and show results of preliminary experiments looking at light shifts.

Sep 1, 20140 citations

Single atom detection on an atom chip with integrated optics

Marco Wilzbach

The subject of this thesis is the miniaturization and integration of detectors for the detection of single rubidium atoms on an atom chip. For this purpose three different detectors were developed for atom detection by absorption or fluorescence: i) A fluorescence detector was realized by mounting a tapered lensed fiber perpendicular to a collection fiber. ii) An absorption detector was built by placing a multi-mode fiber in-line with a tapered lensed fiber. iii) A tunable cavity detector was built from two single mode fibers mounted on the chip surface. To mount the detectors on the planar surface of the atom chip retaining structures by means of lithographical techniques were developed. Those structures allow a very accurate and stable passive fiber alignment. To test the individual detectors an atomic ensemble of thermal rubidium atoms was prepared in a magneto-optical trap. Then the atoms were transferred into magnetic micro-traps of the atom chip and were guided to one of the detectors. Each integrated detector has been evaluated by several characterization measurements. With the fluorescence detector the highest single atom detection efficiency of 54\\% was attained. Thereby it was possible to perform quantitative measurements for the magnetically guided atoms on a single atom level and to study fundamental properties of the confined atoms.

Jan 1, 20070 citations

Towards an integrated atom chip

G. Lewis

The field of atom chips is a relatively new area of research which is rapidly becoming of great interest to the scientific community. It started out as a small branch of cold atom physics which has quickly grown into a multidisciplinary\nsubject. It now encompasses topics from fundamental atomic and quantum theory, optics and laser science, to the engineering of ultra sensitive sensors.\n\nIn this thesis the first steps are taken towards a truly integrated atom chip device for real world applications. Multiple devices are presented that allow the trapping, cooling, manipulation and counting of atoms. Each device presents a new component required for the integration and miniaturisation of atom chips\ninto a single device, capable of being used as a sensor.\n\nInitially, a wire trap was created capable of trapping and splitting a cloud of BoseEinstein condensate (BEC) for use in atom interferometry. Using this chip a BEC has been successfully created, trapped and coherent splitting of this cloud has been achieved.\n\nSubsequently, the integration and simplification of the initial trapping process was approached. In all the experiments to date, atoms are initially collected from a warm vapour by a magneto-optical trap (MOT). This thesis presents a new approach in which microscopic pyramidal MOTs’ are integrated into the chip itself. This greatly reduces the number of optical components and helps to simplify the process significantly.\n\nAlso presented is a method for creating a planar-concave micro-cavity capable of single atom detection. One such cavity consists of a concave mirror fabricated in silicon and the planar tip of an optical fibre. The performance of the resonators\nis highly dependent on the surface roughness and shape profile of the concave mirrors therefore a detailed study into the fabrication technique and its effects on these parameters was undertaken. Using such cavities single atom detection has been shown to be possible. These cavities have also been sccessfully integrated into an atom wire guide.\n\nFinally a co-sputtered amorphous silicon/titanium (a-Si/Ti) nanocomposite material was created and studied for its use as a novel structural material. This material is potentially suitable for integrated circuitry (IC)/Micro-electromechanical-\nsystems (MEMS) integration. The material’s electrical and\nstructural properties were investigated and initial results suggest that a-Si/Ti has the potential to be a compelling structural material for future IC/MEMS integration.\n\nTo build all of these devices, a full range of standard microfabrication techniques was necessary as well as some non standard processes that required considerable process development such as the electrochemical deposition.\n\nThis thesis presents a tool box of fabrication techniques for creating various components capable of different tasks that can be integrated into a single device. Each component has been successfully demonstrated in laboratory conditions. This represents a significant step toward a real world atom chip device.

Mar 1, 20090 citations

Integrating cold caesium atoms into optical waveguides

Elisa Da Ros

This project focuses on a novel experimental method for interfacing cold atoms with optical waveguides. This relies on the introduction of cold atoms into microscopic laser-drilled holes that are perpendicular to the propagation axis of the waveguide. Direct interfacing of cold atoms with the guided mode of a waveguide is an attractive mechanism by which to create atom-photon interfaces, as the small mode area increases the interaction rate. Unlike many previous approaches, this technique can be applied in almost any existing waveguide system, including chip-based waveguide arrays and other complex environments. It therefore has great promise as a way of creating hybrid atom-photon quantum devices. Using this method, we demonstrate coupling between cold atoms and the light propagating in the core of an untapered single-mode optical fibre. This was achieved by laser-drilling a cylindrical, transverse hole (30 μm diameter) through the core of the fibre. Ensembles of cold caesium atoms can be tightly confined through an optical dipole trap within the microscopic void. Probe light, resonant with the Cs D2 line, is then coupled into the fibre. By measuring the transmitted optical power through the interface, it was determined that up to 87% of the probe power could be absorbed by the atoms. The corresponding optical depth per unit length of the atom cloud is over 700 cm^(-1), higher than any value reported to date for a comparable system. This will be a key parameter for the miniaturisation of atom-optical systems as well as for enhancing spatial resolution in sensing applications. The dependence of this absorption on several experimental parameters was also characterised and found to be in line with theoretical expectations. The atomic transition is not noticeably broadened by the presence of the fibre. We have also carried out numerical simulations of light transmission across wave-guide junctions of this type, proving that tailored hole geometries can enable enhanced optical transmission. The achievable degree of improvement is such that it is conceivable to place the void within an optical resonator, for example using laser-written Bragg gratings, and to achieve the strong coupling between the atoms and the guided light. Altogether this work demonstrates the potential of this technique to interface atoms with tightly confined light, allowing for integration in otherwise purely photonic circuits. In such environment the interaction between the atomic ensemble and the light can act as a node for the storage and processing of quantum information.

Dec 31, 20200 citations

Enabling Technologies for Integrated Atom Chips

Matthew Aldous, Rushton, Jo, Himsworth, Matt

The confinement and control of atomic clouds, at temperatures measured in nanokelvin, has become a valuable tool for physicists. As a source of new physics, development of cooling techniques has led to innovative new ways to probe the nature of reality. Of particular note are experiments carried out on new and exotic states of matter such as the Bose-Einstein condensate, unseen before the advent of these techniques. Likewise, the potential for applications outside of the lab is extensive and encompasses navigation, timekeeping, quantum communication and quantum computing. Manipulating cold atoms in the presence of a so-called ‘atom chip’ (a millimetre-scale electronic device) is currently considered the future of miniaturising these experiments and measurements, but since they still require precisely locked and stabilised lasers and predominantly must take place in the ultra-high vacuum regime, quantum control relies on an extensive and well-established infrastructure of optics, electronics, vacuum chambers and pumps. This encumbrance has slowed down the transition from chip-in-a-lab experiments to lab-on-a-chip technologies. This thesis is an account of work carried out in the development of enabling technologies which will accelerate this transition, including details of prototype devices made using established semiconductor and MEMS planar fabrication techniques. The construction and testing of an apparatus for anodically and eutectically bonding die-scale samples in ultra-high vacuum is described, along with an analysis and characterisation of some of its products.

Jan 1, 20142 citations