Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

TEION KOGAKU (Journal of Cryogenics and Superconductivity Society of Japan)

ミリ波・サブミリ波検出器

Kazuo Fujisawa

Published Jan 1, 1980• 0 citations
Publisher

Abstract

In this report, Josephson junction detectors for millimeter and submillimeter waves are surveyed. Emphasis is placed on heterodyne detectors (mixers). Others are briefly referred to, such as video detectors, bolometers, quasiparticle mixers and parametric amplifiers. Also, three kinds of Josephson junctions for detector use are mentioned and brief comments are given on them. These are tunnel junctions, thin film microbridges and point contacts.Thermally cyclable oxide barrier tunnel junctions have been obtained and used as low noise quasiparticle mixers at 115GHz. They have lower noise temperatures compared to Josephson effect mixers, but the receiver noise temperatures are not lowered owing to their lower conversion efficiencies. Thin film microbridges suffer from low junction resistances and also from heating effects caused by d.c. bias supply and r.f. incident power. There seems to exist many problems to be overcome in order to make good submillimeter wave detectors by tunnel junctions or microbridges.Point contacts are now widely used as sensitive detectors for millimeter and submillimeter waves. Although there exist difficulties for making rugged and thermally cyclable point contacts, the techniques for making them have made considerable progress, and a new construction of detector mount has appeared, which brought a low noise mixer at 115GHz thermally cyclable.It is shown that the sensitivity of video detectors decreases as proportional to the inverse square of frequency. So, for submillimeter waves, video detectors are inferior to superconducting bolometers.Recent progress in heterodyne detectors (fundamental and harmonic mixers) are touched on. They are superior to Shottky diode mixers in that they have much smaller NEP's and much higher conversion efficiencies (especially in harmonic mixers), and also in that they operate with much smaller LO power. Experimental curves of IF output power v.s. bias voltage are given for harmonic mixers with harmonic number N=7 and N=10. It is noted that harmonic mixers with even harmonic number are preferable, because they can operate at zero bias voltage. Among them, low even numbers 2 or 4 are recommended in regards to good conversion efficiency.By using Josephson junctions, a peculiar parametric operation is possible, namely doubly degenerate mode. This mode operates under zero d.c. bias by choosing pump frequency as 2ωp=ωs+ωi, ωp-ωs-ωi. Zero bias operation allows the adoption of microbridge arrays. A parametric amplifier with 160 microbridge arrays was built at 33GHz, and showed amplifier gain of 15dB and noise temperature of 20K.

DOI
10.2221/jcsj.15.22

Related papers

Superconducting detectors for infrared and millimeter waves

Paul L. Richards

Quasiparticle and Josephson tunneling currents in superconducting tunnel junctions provide nonlinear low-noise response up to terahertz frequencies. Many types of direct detector heterodyne mixer and parametric amplifier based on these effects have been explored. Only the SIS quasiparticle mixer has been sufficiently competitive to find significant applications. These mixers can have noise approaching the quantum limit TN = ℏω/k and gain larger than 10 dB. They are used at a number of observatories for molecular line radio astronomy at millimeter wavelengths. Similar applications at submillimeter wavelengths are beginning.

Conference on Lasers and Electro-Optics•Apr 25, 1988•0 citations

Superconducting devices for millimeter and submillimeter wavelengths

P. L. Richards

Josephson junctions are highly nonlinear and respond up to infrared frequencies. A wide variety of high frequency applications have been explored. In addition, several high frequency superconducting devices are being developed which do not use the Josephson effect. These include a superconducting version of the Schottky barrier diode for use as a heterodyne mixer and a video detector, and also a composite superconducting bolometer. In this review, the state of development of superconducting mixers, detectors, and parametric amplifiers at microwave, millimeter, and submillimeter wavelengths is discussed. Emphasis will be placed on developments which have taken place since 1974 when a previous review was circulated.

De Gruyter eBooks•Dec 31, 1977•7 citations

Low-Noise Superconducting Mixers for the Terahertz Frequency Range

Victor Y. Belitsky, Serguei Cherednichenko, Dag Winkler

This chapter discusses the high sensitivity superconducting mixers, i.e. detectors used in heterodyne receivers. Today, there are essentially two very successful concepts of superconducting mixers, or frequency down-converters, the superconductor-insulator-superconductor tunnel junction SIS mixer and the superconducting hot-electron bolometer mixer. Moving up to higher frequencies in the microwave and millimeter wave electromagnetic spectra makes it more and more difficult to retrieve a good signal-to-noise ratio with ordinary solid-state amplifiers. The driving force for using superconducting mixers is their excellent down-conversion efficiency and capability to down-convert RF signals from microwave frequencies up to the terahertz region. The main purpose of a receiver is to pick up and amplify a weak signal, which can then be accurately determined in amplitude and phase. The mixer noise temperature and conversion gain are the most important parameters for the mixing device. The Josephson junction mixer was one of the first suggested devices based on superconducting point contacts and later tunnel junctions.

CRC Press eBooks•May 17, 2022•1 citation

Studies of noise in Josephson-effect mixers and their potential for submillimeter heterodyne detection

Robert J. Schoelkopf

NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.

•Nov 7, 2007•5 citations

SMMW detectors; quasiparticle mixer and Josephson mixer using superconducting tunnel junction

Syozo Imai, Seizo Morita, Yosihisa Takeuti +1 more

There are growing needs for low noise and wide band receiver in SMMW range, e.g., in radio astronomy [1]. Hitherto, Schottky diode mixer, Josephson mixer using point contact microbridges, and quasiparticle mixer using superconducting tunnel junctions have been investigated intensively in MMW range. Over wide SMMW range, however, only Schottky diode mixer was tested and used at present. Quasiparticle mixer now confronts a basic difficulty for operation in SMMW range, although it has very high potential as a SMMW mixer. On the otherhand, potential of Josephson mixer using microbridges is unclear.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Dec 1, 1985•0 citations

Superconductive devices for millimeter wave detection, mixing, and amplification

P. L. Richards, Tek-Ming Shen

Single-particle (quasi-particle) tunneling through an insulating barrier between two superconductors or between a superconductor and a normal conductor is being used to make very-low-noise detectors and mixers for millimeter wavelengths. The nonlinearity of theI-Vcurve obtained from tunneling between two superconductors can be so strong that classical theory breaks down and photon-assisted tunneling theory must be used to understand device performance. Quantum theory predicts that a quasi-particle tunnel junction can be operated as a microwave photon detector with quantum efficiency close to unity or as a heterodyne mixer with conversion gain and with mixer noise temperature comparable with the quantum noise limitT_{M} =\bar{h}\omega/k. Both of these predictions have been experimentally realized at 36 GHz using superconductor-insulator-superconductor (SIS) junctions. It appears probable that these quasi-particle detectors and mixers will supercede the corresponding Josephson-effect devices at millimeter wavelengths.

IEEE Transactions on Electron Devices•Oct 1, 1980•61 citations
In this report, Josephson junction detectors for millimeter and submillimeter waves are surveyed. Emphasis is placed on heterodyne detectors (mixers). Others are briefly referred to, such as video detectors, bolometers, quasiparticle mixers and parametric amplifiers. Also, three kinds of Josephson junctions for detector use are mentioned and brief comments are given on them. These are tunnel junctions, thin film microbridges and point contacts.Thermally cyclable oxide barrier tunnel junctions have been obtained and used as low noise quasiparticle mixers at 115GHz. They have lower noise temperatures compared to Josephson effect mixers, but the receiver noise temperatures are not lowered owing to their lower conversion efficiencies. Thin film microbridges suffer from low junction resistances and also from heating effects caused by d.c. bias supply and r.f. incident power. There seems to exist many problems to be overcome in order to make good submillimeter wave detectors by tunnel junctions or microbridges.Point contacts are now widely used as sensitive detectors for millimeter and submillimeter waves. Although there exist difficulties for making rugged and thermally cyclable point contacts, the techniques for making them have made considerable progress, and a new construction of detector mount has appeared, which brought a low noise mixer at 115GHz thermally cyclable.It is shown that the sensitivity of video detectors decreases as proportional to the inverse square of frequency. So, for submillimeter waves, video detectors are inferior to superconducting bolometers.Recent progress in heterodyne detectors (fundamental and harmonic mixers) are touched on. They are superior to Shottky diode mixers in that they have much smaller NEP's and much higher conversion efficiencies (especially in harmonic mixers), and also in that they operate with much smaller LO power. Experimental curves of IF output power v.s. bias voltage are given for harmonic mixers with harmonic number N=7 and N=10. It is noted that harmonic mixers with even harmonic number are preferable, because they can operate at zero bias voltage. Among them, low even numbers 2 or 4 are recommended in regards to good conversion efficiency.By using Josephson junctions, a peculiar parametric operation is possible, namely doubly degenerate mode. This mode operates under zero d.c. bias by choosing pump frequency as 2ωp=ωs+ωi, ωp-ωs-ωi. Zero bias operation allows the adoption of microbridge arrays. A parametric amplifier with 160 microbridge arrays was built at 33GHz, and showed amplifier gain of 15dB and noise temperature of 20K.
Quasiparticle and Josephson tunneling currents in superconducting tunnel junctions provide nonlinear low-noise response up to terahertz frequencies. Many types of direct detector heterodyne mixer and parametric amplifier based on these effects have been explored. Only the SIS quasiparticle mixer has been sufficiently competitive to find significant applications. These mixers can have noise approaching the quantum limit TN = ℏω/k and gain larger than 10 dB. They are used at a number of observatories for molecular line radio astronomy at millimeter wavelengths. Similar applications at submillimeter wavelengths are beginning.
Josephson junctions are highly nonlinear and respond up to infrared frequencies. A wide variety of high frequency applications have been explored. In addition, several high frequency superconducting devices are being developed which do not use the Josephson effect. These include a superconducting version of the Schottky barrier diode for use as a heterodyne mixer and a video detector, and also a composite superconducting bolometer. In this review, the state of development of superconducting mixers, detectors, and parametric amplifiers at microwave, millimeter, and submillimeter wavelengths is discussed. Emphasis will be placed on developments which have taken place since 1974 when a previous review was circulated.
This chapter discusses the high sensitivity superconducting mixers, i.e. detectors used in heterodyne receivers. Today, there are essentially two very successful concepts of superconducting mixers, or frequency down-converters, the superconductor-insulator-superconductor tunnel junction SIS mixer and the superconducting hot-electron bolometer mixer. Moving up to higher frequencies in the microwave and millimeter wave electromagnetic spectra makes it more and more difficult to retrieve a good signal-to-noise ratio with ordinary solid-state amplifiers. The driving force for using superconducting mixers is their excellent down-conversion efficiency and capability to down-convert RF signals from microwave frequencies up to the terahertz region. The main purpose of a receiver is to pick up and amplify a weak signal, which can then be accurately determined in amplitude and phase. The mixer noise temperature and conversion gain are the most important parameters for the mixing device. The Josephson junction mixer was one of the first suggested devices based on superconducting point contacts and later tunnel junctions.
NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.
There are growing needs for low noise and wide band receiver in SMMW range, e.g., in radio astronomy [1]. Hitherto, Schottky diode mixer, Josephson mixer using point contact microbridges, and quasiparticle mixer using superconducting tunnel junctions have been investigated intensively in MMW range. Over wide SMMW range, however, only Schottky diode mixer was tested and used at present. Quasiparticle mixer now confronts a basic difficulty for operation in SMMW range, although it has very high potential as a SMMW mixer. On the otherhand, potential of Josephson mixer using microbridges is unclear.
Single-particle (quasi-particle) tunneling through an insulating barrier between two superconductors or between a superconductor and a normal conductor is being used to make very-low-noise detectors and mixers for millimeter wavelengths. The nonlinearity of theI-Vcurve obtained from tunneling between two superconductors can be so strong that classical theory breaks down and photon-assisted tunneling theory must be used to understand device performance. Quantum theory predicts that a quasi-particle tunnel junction can be operated as a microwave photon detector with quantum efficiency close to unity or as a heterodyne mixer with conversion gain and with mixer noise temperature comparable with the quantum noise limitT_{M} =\bar{h}\omega/k. Both of these predictions have been experimentally realized at 36 GHz using superconductor-insulator-superconductor (SIS) junctions. It appears probable that these quasi-particle detectors and mixers will supercede the corresponding Josephson-effect devices at millimeter wavelengths.