This thesis reports on the design, setup, and operation of a new atom trap apparatus, which is developed to confine few rubidium atoms in ultrahigh vacuum by means of taylored and dynamically variable light potentials (dipole traps), thus making the atoms available for spectroscopy and controlled manipulations. To maintain low background pressure, atoms of a vapour cell are transferred into a cold atomic beam by laser cooling techniques, and accumulated by a magneto-optic trap (MOT) in a separate part of the vacuum system. The laser cooled atoms are then transferred into dipole traps made of focused far-off-resonant laser fields in single or crossed-beam geometry, which are superimposed with the center of the MOT. Gaussian as well as hollow Laguerre-Gaussian (LG01) beam profiles are used with red-detuned and blue-detuned light. Microfabricated dielectric phase objects allow the efficient and robust mode conversion of Gaussian into Laguerre-Gaussian laser beams. Trap geometries can easily be changed due to the highly flexible experimental setup. The dipole trap laser beams have powers up to several hundred milliwatts and are focused to around 10 m. At a detuning of several tens of nanometers from the atomic resonance, the resulting traps are a few millikelvin deep, and the trapped atoms exhibit motional frequencies near 30 kHz, trap light scattering rates of a few hundred photons per second per atom, and storage times of several seconds. The number of dipole-trapped atoms ranges from more than ten thousand to below ten. The dipole-trapped atoms are detected either by a photon counting system with efficient straylight discrimination, or by recapture into the MOT, which is imaged onto a sensitive photodiode and a CCD-camera. Due to the strong AC-Stark shift imposed by the high-intensity trapping light, energy-selective resonant excitation and detection of the stored atoms is possible. The measured energy distribution is consistent with a harmonic potential shape and allows for the determination of temperatures and heating rates. From initial measurements, the thermal energy is found to be about 10 % of the trap depth. Using a crossed-beam geometry with red-detuned laser light, efficient transfer of atoms between the beams is observed. Optimum transfer occurs when the two beams cross at a radial offset, which can qualitatively be understood when the particle energy and geometrical properties of the two-beam trapping potential are considered. Numerical simulations reproduce the general features of the measured transfer efficiency vs. radial beam offset. This experiment is a first step towards dynamically variable potentials. Atoms have been radially confined in a blue-detuned hollow beam, and their decay time has been determined. This configuration is currently extended to a three-dimensionally confining blue-detuned dipole trap. For advanced laser cooling, state manipulation and spectroscopy of trapped atoms, a system of two diode lasers has been set up which are phase-coherently locked with a difference frequency near 6.834 GHz, to drive Raman transitions between the hyperfine-split ground states of 87Rb atoms. Resonances of such a transition have been recorded in a buffer gas loaded rubidium vapour cell with linewidths below 100 Hz.
This thesis reports on the design, setup, and operation of a new atom trap apparatus, which is developed to confine few rubidium atoms in ultrahigh vacuum by means of taylored and dynamically variable light potentials (dipole traps), thus making the atoms available for spectroscopy and controlled manipulations. To maintain low background pressure, atoms of a vapour cell are transferred into a cold atomic beam by laser cooling techniques, and accumulated by a magneto-optic trap (MOT) in a separate part of the vacuum system. The laser cooled atoms are then transferred into dipole traps made of focused far-off-resonant laser fields in single or crossed-beam geometry, which are superimposed with the center of the MOT. Gaussian as well as hollow Laguerre-Gaussian (LG01) beam profiles are used with red-detuned and blue-detuned light. Microfabricated dielectric phase objects allow the efficient and robust mode conversion of Gaussian into Laguerre-Gaussian laser beams. Trap geometries can easily be changed due to the highly flexible experimental setup. The dipole trap laser beams have powers up to several hundred milliwatts and are focused to around 10 m. At a detuning of several tens of nanometers from the atomic resonance, the resulting traps are a few millikelvin deep, and the trapped atoms exhibit motional frequencies near 30 kHz, trap light scattering rates of a few hundred photons per second per atom, and storage times of several seconds. The number of dipole-trapped atoms ranges from more than ten thousand to below ten. The dipole-trapped atoms are detected either by a photon counting system with efficient straylight discrimination, or by recapture into the MOT, which is imaged onto a sensitive photodiode and a CCD-camera. Due to the strong AC-Stark shift imposed by the high-intensity trapping light, energy-selective resonant excitation and detection of the stored atoms is possible. The measured energy distribution is consistent with a harmonic potential shape and allows for the determination of temperatures and heating rates. From initial measurements, the thermal energy is found to be about 10 % of the trap depth. Using a crossed-beam geometry with red-detuned laser light, efficient transfer of atoms between the beams is observed. Optimum transfer occurs when the two beams cross at a radial offset, which can qualitatively be understood when the particle energy and geometrical properties of the two-beam trapping potential are considered. Numerical simulations reproduce the general features of the measured transfer efficiency vs. radial beam offset. This experiment is a first step towards dynamically variable potentials. Atoms have been radially confined in a blue-detuned hollow beam, and their decay time has been determined. This configuration is currently extended to a three-dimensionally confining blue-detuned dipole trap. For advanced laser cooling, state manipulation and spectroscopy of trapped atoms, a system of two diode lasers has been set up which are phase-coherently locked with a difference frequency near 6.834 GHz, to drive Raman transitions between the hyperfine-split ground states of 87Rb atoms. Resonances of such a transition have been recorded in a buffer gas loaded rubidium vapour cell with linewidths below 100 Hz.
This thesis reports on the design and construction of, and results from, an optical-dipole trapping apparatus developed to confine ultracold rubidium atoms in a conservative, large period, optical-dipole trap. An ultra-high vacuum system was designed and constructed to create a very low- background pressure. A new technique of viewport construction was developed, allowing for the fabrication of economical, high-quality windows for transmission of mid-infra-red laser radiation. The construction of a magneto-optical trap (MOT) and an optical molasses, and the subsequent characterisation, are discussed. A theory for the ac-Stark shift of atoms in a far-detuned laser field was developed. The nature of the scalar and tensorial light-shifts of the ground and first excited states of alkali atoms - the 5s(^2)S1/2 and 5p(^2)P3/2 states of Rb - has been examined. The effect of the differential light-shifts between these states on the operation of efficient laser cooling is discussed. A quasi-electrostatic dipole trap (QUEST) was formed from 50 W of CO2 laser power (٢ = 10.6 μm), focussed to <100 μm. The transfer of ultra-cold atoms from the MOT and optical molasses to the QUEST have been examined. Single beam and standing wave geometries of the QUEST have been implemented, with lifetimes of many seconds. The theory for the ac-Stark effect due to a single laser field has been further developed to consider orthogonally polarised fields with independent wavelengths. The use of an auxiliary laser field, a Nd:YAG laser at λ = 1.064 μm, to enhance the number and density of atoms loaded into the QUEST has been proposed and realised.
This dissertation reports on the design, construction, and investigation of a pulsed optical dipole force trap which uses laser light to confine ultracold rubidium (Rb) atoms. Because the laser frequency is detuned far from the atomic resonance frequency, the optical dipole force trap is also called a "far-off-resonance trap" (FORT). The use of pulsed laser light to create an optical trap may find application in expanding the number of atomic species which can be confined. The experiments reported here are principally aimed, however, at understanding the physics of pulsed FORT dynamics in anticipation of using the free electron laser (FEL) at Jefferson Lab (Jlab) to construct a FORT. The Jlab FEL will provide a tunable, high power laser light source enabling the realization of spatially large and/or energetically deep traps which are not presently accessible with table-top laser sources. Here, a mode-locked Nd:YAG laser is used as a pulsed laser source. Since the conservative optical dipole force trap does not cool Rb atoms, ultracold atoms must be loaded into the FORT. The optical dipole force trap is formed at the focus of a Gaussian, 1.06 μm Nd:YAG laser beam which is located at the center of a high vacuum chamber and superimposed onto the center of a pre-cooled Rb atom cloud that has been previously accumulated in a magneto-optic trap (MOT). The performance of the pulsed FORT is compared to a continuous wave mode (cw) FORT which is built using the same laser beam; the operation of the two kinds of FORTs can be switched easily without disturbing the experimental alignment. The dependencies of FORT loading efficiency to FORT and MOT parameters such as FORT laser power, loading time, storage/holding time, detuning of the primary MOT laser frequency, and repump laser intensity are investigated. There are about 1.5×107 ultracold rubidium atoms in the MOT. At 7 Watts FORT laser power, about 8% of the atoms are loaded successfully into the cw FORT and about 5% into the pulsed FORT under similar, but not identical, conditions. In most respects both the cw and pulsed FORTs show comparable behavior. The behavior of both FORTs depends strongly on FORT laser power. As expected, at higher power, more atoms can be loaded into the FORT. Both FORTs also depend on the loading time and holding time.
During the course of this PhD an experimental set-up has been designed and implemented to confine neutral atoms in microscopic dipole traps and to manipulate their internal states by laser excitation to Rydberg states. A lot of effort was devoted to the stabilization of the laser sources for two-photon excitation to the Rydberg states, using techniques based on modulation transfer spectroscopy and electromagnetically induced transparency (EIT). Taking advantage of the EIT spectroscopy scheme, we have measured for the first time the electric dipole moments for the transitions between the first excited 5P3/2 and Rydberg nDS/2 level of rubidium. These measurements provided benchmarking of existing theoretical models to calculate the reduced matrix elements and have helped us to identify the D'yachkov Pankratov method as a particularly reliable one. Therefore we made use of the existing code to calculate the relative radial matrix elements for bound-bound, bound-free and free-free transitions between arbitrary states of alkali atoms. Our results allowed us to identify many features of interest and several Cooper minima have been revealed for the first time. The preparation of a new apparatus required ultra-high vacuum for efficient laser cooling and trapping experiments. A unique 4-beam magneto-optical trap has been designed and implemented in our new system. The tetrahedral MOT operating at a very acute beams angle has been demonstrated for the first time. The characterisation of the basic properties of our MOT has highlighted. some interesting new cooling mechanisms that do not fully match existing theoretical models and will require further investigation. It has been demonstrated that our tetrahedral MOT is suitable to prepare cold, diluted reservoirs of atoms and therefore efficiently load our microscopic dipole trap.
The interaction of light with atoms and molecules is of fundamental interest in many branches of science. In atomic physics, this interaction can be used to cool and spatially confine (trap) atoms. These traps can be used as the starting point for other experiments, but the dynamics of the cooling and trapping processes is itself of interest. In order to better understand the physics of trapping atoms in an optical dipole force trap, we have conducted a series of spectroscopic measurements of ultracold rubidium atoms in such a trap. The trap was created at the focus of a Nd:YAG laser beam with wavelength 1064nm and nearly Gaussian spatial mode. For rubidium, the trap light is red-detuned and the atoms are confined to the highest intensity in the beam. In order to probe the atoms confined in the trap, we have performed spectroscopy on the 5S1/2 → 5P3/2 transition. Because the polarizability of the ground and excited states is not the same at the trap wavelength, the spectra exhibit both a shift and inhomogeneous broadening. We have investigated the spectra for both linear and circular polarized traps. We also studied the application of a second laser to couple the excited state (5P3/2) to another higher excited state (5D5/2) to reduce the inhomogeneous broadening of the 5S1/2 → 5P 3/2 transition. Finally, two-photon spectroscopy was performed on atoms in the dipole force trap and compared to spectra taken in a magneto optical trap (MOT). Autler-Townes splitting was clearly observed in the MOT and appears to have been observed in the dipole force trap also.
The subject of this thesis is the construction and characterization of an experimental setup for studying the interaction of an ensemble of 10^5 - 10^6 cold 87 Rb atoms held in a far off-resonance optical dipole trap with a probe detuned by about 100 natural line widths, a regime in which refractive effects are resonantly enhanced but absorption is small. An important feature of this type of atom-light interface is that it facilitates quantum non-demolition measurements which in turn have numerous applications in quantum information technology, as well as in the field of ultra-precise metrology where they allow the measurements to overcome the so-called standard quantum limit.
The use of a dipole trap has several advantages over more conventional approaches in which vapor cells or magneto-optical traps (MOT) have been used. Most importantly interaction strength of comparable magnitude can be achieved with a far lower number of atoms and with longer coherence times. The elongated geometry that can be realized in a dipole trap maximizes the interaction strength. One of the complications that arise is that the achievable interaction strength is highly sensitive to the mode-matching between the trapped ensemble and the probe beam.
The theoretical description of the interaction between a trapped ensemble and a freely-propagating probe beam is provided in the framework of continuous variables. The relevant quantities are a pseudo-spin, defined for an ensemble of atoms in their ground state, and the Stokes vector that characterizes the polarization state of light. In practice the experiment consists of four main blocks: the atom traps, the optical pumping setup, the probe laser setup, and the photodetection.
Before loading into the dipole trap, atoms are cooled in a MOT. An existing MOT setup has been improved by implementing a new, more powerful laser system. A dedicated dipole trap, which had been constructed in collaboration with another project, has been thoroughly characterized and the results are presented in this thesis. Setups for optical pumping and for the probe have been built, characterized and incorporated into the apparatus.
Several experimental techniques have been developed and tested in order to optimize the alignment of the probe with the trapped ensemble. The effect of the geometrical overlap on the achievable signal to noise ratio is discussed and illustrated using simple, intuitive models.
Photo-detection is a critical part of the setup. In order to facilitate detection of non-classical (squeezed) states of the atomic (pseudo-) spin, the detection system must be shot-noise limited within the range of photon numbers used in the experiments. Such a system has been constructed and tested, and is described in detail. It employs a charge-sensitive amplifier (CSA) but, unlike earlier implementations, it does not use a pulse-shaping stage. Instead, an algorithm has been devised and implemented that derives the quantities of interest directly from the output signal of the CSA. This novel approach avoids the technical problems that arise in systems using hardware-based pulse shaping. It also makes the detector more flexible in terms of the shape and timing of the probe pulses that can be used.
The atomic states produced in the setup are intrinsically sensitive to stray magnetic fields. Therefore an efficient cancellation of stray fields is essential. On the other hand having the possibility to apply a fully controlled, external magnetic field makes the experimental setup more versatile. Both goals can be achieved with a magnetic field control unit that has been built during this project. It facilitates active cancellation of stray magnetic fields at the frequency of the mains and in addition allows to apply an arbitrary waveform magnetic fields along all three axes. One of the main results reported in this thesis is the observation of polarization rotation caused by population imbalance created in the process of optical pumping and, in a separate series of measurements, due to an applied magnetic field. These measurements have allowed us to assess the strength of the atom-light interaction available in the current setup. They indicate that with the necessary modifications to the optical pumping scheme the system should prove successful in implementing quantum information protocols, in particular quantum memory for light.
An interesting off-shoot has been the spectroscopic characterization of the atomic state in the dipole trap. In these measurements Doppler free spectra are recorded in a very simple setup without the need to use nonlinear techniques. Apart from providing a method to characterize the efficiency of the optical pumping into the hyperfine level of interest, the acquired spectra are a very direct illustration of the power of the laser cooling techniques developed in the recent years and without which this work would not have been possible.
We discuss our recent experimental demonstrations of three novel atom traps which are all based on the optical dipole force in far-detuned laser light. In the gravito-optical surface trap (GOST), Cs atoms are trapped and cooled by means of an evanescent-wave mirror very closely above a dielectric surface. This trap allows for optical cooling at very high densities and provides good starting conditions for evaporative cooling to quantum degeneracy and the realization of a 2D quantum gas. The conical atom trap (CAT) uses a hollow blue-detuned laser beam in combination with gravity to trap atoms in a dark spatial region. This trap is experimentally simple and provides high loading efficiency, tight confinement, efficient sub-Doppler cooling, and strong suppression of collisional losses. The standing-wave red-detuned (STAR) trap allows one to confine atoms in a shallow optical potential at a very low photon scattering rate, and is thus an interesting tool for studies of the atomic ground-state dynamics in external electro-magnetic fields. We have studied atomic spin polarization in this trap.