Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Optics

Backpropagating neurons from bichromatic interaction with a three-level system

David Kagan, Harry Friedmann

Published May 1, 1989• 3 citations
Publisher

Abstract

Optical implementation of a backpropagating neuron by means of a nonlinear Fabry-Perot etalon requires thresholding a forward signal beam while the transmittance of a backpropagating beam is multiplied by the differential of the forward signal. This is achievable by inputting a bichromatic field to a three-level system in an optical cavity. The response characteristics of this device have the added possibility of adaptability of the threshold by the backward probe input intensity.

DOI
10.1364/ao.28.001697

Related papers

Optical Error Correction by Adaptive Thresholding

David Kagan, Harry Friedmann

During the last few years we have suggested1−2 the use of a four-level system irradiated by a bichromatic beam to obtain a tunable optical bistable device. By tunable we mean that the switching threshold can be altered without changing the hardware characteristics, the operating temperature, or the frequencies of the inputs to the device. The basic principle of our suggestion is that by irradiating the non-linear optical material by two beams of appropriately chosen frequencies in an optical cavity, one can act as a signal and the other as tuning control beam. The advantage of the four level system lay in the possibility of using low power control beams which could tune the characteristic optically bistable output curves.

Optical Computing•Jan 1, 1989•0 citations

Signal Processing With A Nonlinear Fabry-Perot

E. Garmire

In this paper we consider the nonlinear Fabry-Perot and its applications to optical signal and image processing. This paper addresses the signal processing aspects of a nonlinear Fabry-Perot interferometer with emphasis on image processing. The device geometry is shown in Figure 1. A thin nonlinear medium, whose refractive index is a function of the light intensity inside the Fabry-Perot is sandwiched between two plane parallel mirrors. The output as a function of input is shown in Fig. 2, for two different values of the difference between the Fabry-Perot low intensity resonance and the incident wavelength. The bistable curve in 2a is the origin of the term optical bistability and makes possible an optical memory, in which the output is a function of the history of the device. The Figure 2b represents a typical nonlinear transfer curve which may be used for signal processing. It can be seen that small changes in the input intensity Ic make large changes in the output intensity.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 29, 1981•5 citations

Optical Bistability

The study of optical bistability and bistable devices is a special topic of nonlinear optics. In this chapter, we focus our discussion only on the most typical optical bistable configuration, i.e. a Fubry–Perot (F–P) etalon containing a nonlinear optical medium, the refractive-index of which depends on the light intensity. Under the action of an intense coherent optical beam, this device may exhibit a nonlinear response to the incident beam in the sense that the transmitted intensity is a nonlinear function of the incident intensity. Based on such a nonlinear response this type of device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element depending on the chosen nonlinear medium and operation conditions.

WORLD SCIENTIFIC eBooks•Dec 14, 2017•0 citations

Optical Bistability

Guang S. He

When the output parameter of an optical device could be a multivalued function of the input parameter, this device can be working in an optical bistable status. The most typical optical bistable device is a Fabry–Perot cavity containing a nonlinear optical medium, the refractive index of which depends on the light intensity. Upon the action of an intense input optical beam, the transmitted (or reflected) intensity of this device may exhibit a nonlinear response to the incident light intensity variation and, especially under appropriate working conditions, the characteristic output/input curve may manifest a single (or multiple) hysteresis loop(s). Such type of optical bistable device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element, depending on the chosen nonlinear medium and operation conditions.

Oxford University Press eBooks•Oct 30, 2014•1 citation

Guided-wave controlled etalons

Dror Sarid

Abstract Optical bistability in a nonlinear Fabry-Perot etalon can be controlled by several optical beams injected through the edges of the etalon. The control beams, which propagate transversely in the etalon, modify the refractive index, which in turn switches the etalon between its two stable states. The theory of operation of the device is presented, possible logical operations are discussed and experimental results from using an InSb etalon and a CO laser are reported.

Philosophical Transactions of the Royal Society of London Series A Mathematical and Physical Sciences•Dec 18, 1984•1 citation

OPTICAL FLIP-FLOP AND LOGIC GATE OPERATIONS WITH ZnSe NONLINEAR ETALONS USING TWO LIGHT BEAMS

Takashi Kurokawa, Hiroyuki Tsuda, S. Fukushima

There has recently been increasing interest in bistable optical devices because of their potential for all-optical signal processing in optical computing systems and optical transmission networks(1), (2). Nonlinear Fabry-Perot etalons whose steady-state properties have been studied extensively are one candidate for such applications. Relatively little work, however, has been done on their operating characteristics and transient behavior(3).

•Jul 18, 1988•0 citations
Optical implementation of a backpropagating neuron by means of a nonlinear Fabry-Perot etalon requires thresholding a forward signal beam while the transmittance of a backpropagating beam is multiplied by the differential of the forward signal. This is achievable by inputting a bichromatic field to a three-level system in an optical cavity. The response characteristics of this device have the added possibility of adaptability of the threshold by the backward probe input intensity.
During the last few years we have suggested1−2 the use of a four-level system irradiated by a bichromatic beam to obtain a tunable optical bistable device. By tunable we mean that the switching threshold can be altered without changing the hardware characteristics, the operating temperature, or the frequencies of the inputs to the device. The basic principle of our suggestion is that by irradiating the non-linear optical material by two beams of appropriately chosen frequencies in an optical cavity, one can act as a signal and the other as tuning control beam. The advantage of the four level system lay in the possibility of using low power control beams which could tune the characteristic optically bistable output curves.
In this paper we consider the nonlinear Fabry-Perot and its applications to optical signal and image processing. This paper addresses the signal processing aspects of a nonlinear Fabry-Perot interferometer with emphasis on image processing. The device geometry is shown in Figure 1. A thin nonlinear medium, whose refractive index is a function of the light intensity inside the Fabry-Perot is sandwiched between two plane parallel mirrors. The output as a function of input is shown in Fig. 2, for two different values of the difference between the Fabry-Perot low intensity resonance and the incident wavelength. The bistable curve in 2a is the origin of the term optical bistability and makes possible an optical memory, in which the output is a function of the history of the device. The Figure 2b represents a typical nonlinear transfer curve which may be used for signal processing. It can be seen that small changes in the input intensity Ic make large changes in the output intensity.
The study of optical bistability and bistable devices is a special topic of nonlinear optics. In this chapter, we focus our discussion only on the most typical optical bistable configuration, i.e. a Fubry–Perot (F–P) etalon containing a nonlinear optical medium, the refractive-index of which depends on the light intensity. Under the action of an intense coherent optical beam, this device may exhibit a nonlinear response to the incident beam in the sense that the transmitted intensity is a nonlinear function of the incident intensity. Based on such a nonlinear response this type of device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element depending on the chosen nonlinear medium and operation conditions.
When the output parameter of an optical device could be a multivalued function of the input parameter, this device can be working in an optical bistable status. The most typical optical bistable device is a Fabry–Perot cavity containing a nonlinear optical medium, the refractive index of which depends on the light intensity. Upon the action of an intense input optical beam, the transmitted (or reflected) intensity of this device may exhibit a nonlinear response to the incident light intensity variation and, especially under appropriate working conditions, the characteristic output/input curve may manifest a single (or multiple) hysteresis loop(s). Such type of optical bistable device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element, depending on the chosen nonlinear medium and operation conditions.