Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Bandwidth and Noise of Submillimeter Wave Cuprate Bicrystal Josephson Junction Detectors

G. A. Ovsyannikov, I. V. Borisenko, K. Y. Constantinian, Y.V. Kislinski, Arsen A. Hakhoumian, N.G. Pogosyan, Tatevik V. Zakaryan, N. F. Pedersen, J. Mygind, N.K. Uzunoglu, Evangelia A. Karagianni

Published Jun 1, 2005• 8 citations
Publisher

Abstract

Detectors made from superconducting cuprate YBa/sub 2/Cu/sub 3/O/sub x/ bicrystal Josephson junctions (BJJs) on sapphire and NdGaO/sub 3/ substrates have been fabricated and characterized in the frequency band 200-900 GHz. Junctions on sapphire substrates had a normal state resistance R/sub N//spl ap/15-60 /spl Omega/, and I/sub C/R/sub N/ product up to 2.5 mV at T=4.2 K. Junctions on NdGaO/sub 3/ substrates had lower R/sub N/=1-5 /spl Omega/ and I/sub C/R/sub N/=0.4-0.9 mV at T=77 K. Three types of detecting devices have been investigated in both the broadband and the frequency-selective detection modes. One type was patterned with log-periodic antenna, and two others with Pt-metal double-slot antenna designed for a central frequency f=300 GHz and f=400 GHz, respectively. Measurements at f=320 GHz of the reception bandwidth /spl Delta/f for a device with double-slot antenna gave a quality factor Q=f//spl Delta/f/spl ap/10. A low-noise cooled 1-2 GHz bandwidth amplifier enables a better sensitivity in the self-pumping frequency mixing mode, avoiding the 1/f noise. The dependence of the spectral density of noise on voltage was compared to the data for the Josephson emission linewidth obtained by the selective detector response method. Also discussed are measurements at 500 GHz of the NEP values carried out at different experimental conditions.

DOI
10.1109/tasc.2005.849902

Related papers

Submillimeter-wave mixing and noise in HTS Josephson junctions

Michael A. Tarasov, Е. А. Степанцов, Dmitry S. Golubev +6 more

A Josephson quasioptical detector comprising YBaCuO junction on bicrystal MgO substrate, integrated log-periodic Au antenna, MgO extended hyperhemisphere lens attached to the substrate and 1.4 GHz cold amplifier with cold circulator has been designed, fabricated and experimentally studied. We fabricated several integrated Josephson junctions 1-2 /spl mu/m wide which at 4.2 K demonstrate RSJ IV curves with critical currents 100-300 /spl mu/A and normal resistance of 10-20 /spl Omega/. The noise temperature (T/sub N/) at 4.2 K and 330 GHz measured by a hot/cold load method in fundamental mixing mode with external BWO local oscillator brings T/sub N/=1100 K for the junction shunted by low-inductance resistive shunt and T/sub N/=1400 K without shunting. At bath temperatures of 20-40 K the noise temperature was in the range 1500-3000 K, at 50 K the noise temperature was below 2000 K, and at 60-70 K increased over 3000 K in the frequency range 310-586 GHz. The noise temperatures measured in the self-pumping mode vary between 580-2300 K with dc bias in the range 0.1-0.5 mV. The linewidth of Josephson oscillations has been extracted from a selective detector response and IF noise voltage dependence. The measured excess noise can be attributed to shot noise and multiple Andreev reflection in pinholes with Ss'S structure. We observed small subharmonic steps in IV curve and noise dependencies, which are typical for SNS junctions.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•8 citations

Shot noise in YBCO bicrystal Josephson junctions

K. Y. Constantinian, G. A. Ovsyannikov, I. V. Borisenko +2 more

We measured spectral noise density in YBCO symmetric bicrystal Josephson junctions on sapphire substrates at bias voltages up to 100 mV and T=4.2 K. Normal state resistance of the Josephson junctions, R/sub N/=20-90 /spl Omega/ and I/sub C/R/sub N/ up to 2.2 mV have been observed in the experimental samples. Noise measurements were carried out within frequency bands of 1-2 GHz and 0.3-300 kHz. At bias voltages 10/spl les/V/spl les/60 mV a linear voltage dependence of noise power has been registered, while at V/spl les/5 mV a noticeable noise rise has been observed. The latter may explain the experimentally measured linewidth broadening of Josephson oscillations at mm and submm wave frequencies in high-Tc superconducting junctions. Experimental results are discussed in terms of bound states existing at surfaces of d-wave superconducting electrodes.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•5 citations

Observation of a voltage-tunable sub-mm wave response from a YBCO Josephson device, operating in self-pumping mode

K. Y. Constantinian, G. A. Ovsyannikov, I. V. Borisenko +1 more

The first experimental data are presented on the observation of a response of a noise signal applied to a tunable-by-voltage high- T C Josephson mixer operating in a self-pumping mode within the frequency band of f = 750–970 GHz at ambient temperature T = 12.5 K. The mixer device was a thin-film YBaCuO bicrystal Josephson junction coupled with the electrodes patterned in log-periodic antenna. Experimental junctions exhibit RSJ-like I–V characteristics with a product of I C R N ≈ 2 mV ( I C is the critical current and R N is the normal state resistance). Down-converted signal response was examined at an intermediate frequency band within 1–2 GHz by means of the Fourier transform spectroscopy technique. Evaluated from Fourier transform spectrograms clear double-side band mixer response functions were registered at any of the fixed bias voltages in the range of V = 1.65–2.1 mV.

Superconductor Science and Technology•Nov 14, 2001•6 citations

A broadband detector based on series YBCO grain boundary Josephson junctions

Egor I. Glushkov, Alexander V. Chiginev, L. S. Kuzmin +1 more

Modeling of a broadband receiving system based on a meander series of Josephson YBaCuO grain boundary junctions integrated into a log-periodic antenna was carried out. The electromagnetic properties of the system, namely amplitude–frequency characteristic, beam pattern, and fraction of the absorbed power in each Josephson junction were investigated. Based on the obtained results, a numerical simulation of one-dimensional arrays was carried out. The dc characteristics of the detector were calculated, that is, current–voltage characteristic, responsivity, noise, and noise-equivalent power (NEP) for a 250 GHz external signal. The optimal number of junctions to obtain the minimum NEP was found. The use of a series of junctions allows one to increase the responsivity by a factor of 2.5, the NEP value by a factor of 1.5, and the power dynamic range by a factor of 5. For typical YBaCuO Josephson junctions fabricated on a ZrYO bicrystal substrate by magnetron deposition, the following parameters were obtained at a temperature of 77 K: responsivity = 9 kV/W; NEP = 3·10−13 W/Hz(1/2); power dynamic range = 1·106.

Beilstein Journal of Nanotechnology•Mar 28, 2022•12 citations

Josephson spectroscopy at submillimetre waves

Michael A. Tarasov, A. Shul’man, N Solopov +8 more

An HTS Josephson spectrometer has been designed, fabricated and experimentally studied. The spectrometer circuit consists of a YBCO bicrystal Josephson junction integrated with a double-slot or log-periodic antenna, connected in parallel with a gold low-inductance shunt. The selective detector response and RF response at intermediate frequency f IF = 1.4 GHz were measured in the signal frequency range f s = 400-1250 GHz and the linewidth of Josephson oscillations (LJO) was determined by using three different methods. (1) The Hilbert spectroscopy approach was used in the processing of the selective detector response. (2) In case of f IF < LJO the detector and RF responses have similar shapes, allowing the spectrum and LJO to be extracted from the RF response and even processing by modified Hilbert spectroscopy. (3) The RF response at f IF > LJO corresponds to the frequency down-conversion in a self-pumped Josephson mixer mode. For the processing of the RF response in the high f IF limit we suggest a novel method that allows extraction of the signal spectrum by means of simple operations: shifting, summing and subtracting. The advantage of the RF response method is in its simplicity and higher sensitivity that allows it to be proposed for spectroscopy applications.

Superconductor Science and Technology•Nov 1, 1999•4 citations

YBa 2 Cu 3 O 7 Josephson junctions on LaAlO3 bicrystals for terahertz-frequency applications

A. Kaestner, M. Volk, Frank Ludwig +2 more

We prepared Josephson junctions made of YBa2Cu3O7 on symmetric 24° LaAlO3 bicrystal substrates. For better coupling of high-frequency radiation, we structured the contacts with logarithmic-periodic antennas made of YBa2Cu3O7. Characterization was done by measuring the voltage–current characteristics to determine the critical current IC, the normal-state resistance RN, the noise parameter Γ, and the Stewart–McCumber parameter βC as predicted by the resistively and capactively shunted junction model (RCSJ). The junctions showed excellent RCSJ-like behavior with ICRN products of up to 2.0 mV at 10 K and 220 μV at 77 K. To demonstrate the possibility to detect high-frequency radiation up to the THz regime, we used the Josephson junction as a detector for radiation from a far-infrared laser and we reconstructed the spectra by Hilbert spectroscopy.

Applied Physics Letters•Nov 6, 2000•23 citations
Detectors made from superconducting cuprate YBa/sub 2/Cu/sub 3/O/sub x/ bicrystal Josephson junctions (BJJs) on sapphire and NdGaO/sub 3/ substrates have been fabricated and characterized in the frequency band 200-900 GHz. Junctions on sapphire substrates had a normal state resistance R/sub N//spl ap/15-60 /spl Omega/, and I/sub C/R/sub N/ product up to 2.5 mV at T=4.2 K. Junctions on NdGaO/sub 3/ substrates had lower R/sub N/=1-5 /spl Omega/ and I/sub C/R/sub N/=0.4-0.9 mV at T=77 K. Three types of detecting devices have been investigated in both the broadband and the frequency-selective detection modes. One type was patterned with log-periodic antenna, and two others with Pt-metal double-slot antenna designed for a central frequency f=300 GHz and f=400 GHz, respectively. Measurements at f=320 GHz of the reception bandwidth /spl Delta/f for a device with double-slot antenna gave a quality factor Q=f//spl Delta/f/spl ap/10. A low-noise cooled 1-2 GHz bandwidth amplifier enables a better sensitivity in the self-pumping frequency mixing mode, avoiding the 1/f noise. The dependence of the spectral density of noise on voltage was compared to the data for the Josephson emission linewidth obtained by the selective detector response method. Also discussed are measurements at 500 GHz of the NEP values carried out at different experimental conditions.
A Josephson quasioptical detector comprising YBaCuO junction on bicrystal MgO substrate, integrated log-periodic Au antenna, MgO extended hyperhemisphere lens attached to the substrate and 1.4 GHz cold amplifier with cold circulator has been designed, fabricated and experimentally studied. We fabricated several integrated Josephson junctions 1-2 /spl mu/m wide which at 4.2 K demonstrate RSJ IV curves with critical currents 100-300 /spl mu/A and normal resistance of 10-20 /spl Omega/. The noise temperature (T/sub N/) at 4.2 K and 330 GHz measured by a hot/cold load method in fundamental mixing mode with external BWO local oscillator brings T/sub N/=1100 K for the junction shunted by low-inductance resistive shunt and T/sub N/=1400 K without shunting. At bath temperatures of 20-40 K the noise temperature was in the range 1500-3000 K, at 50 K the noise temperature was below 2000 K, and at 60-70 K increased over 3000 K in the frequency range 310-586 GHz. The noise temperatures measured in the self-pumping mode vary between 580-2300 K with dc bias in the range 0.1-0.5 mV. The linewidth of Josephson oscillations has been extracted from a selective detector response and IF noise voltage dependence. The measured excess noise can be attributed to shot noise and multiple Andreev reflection in pinholes with Ss'S structure. We observed small subharmonic steps in IV curve and noise dependencies, which are typical for SNS junctions.
We measured spectral noise density in YBCO symmetric bicrystal Josephson junctions on sapphire substrates at bias voltages up to 100 mV and T=4.2 K. Normal state resistance of the Josephson junctions, R/sub N/=20-90 /spl Omega/ and I/sub C/R/sub N/ up to 2.2 mV have been observed in the experimental samples. Noise measurements were carried out within frequency bands of 1-2 GHz and 0.3-300 kHz. At bias voltages 10/spl les/V/spl les/60 mV a linear voltage dependence of noise power has been registered, while at V/spl les/5 mV a noticeable noise rise has been observed. The latter may explain the experimentally measured linewidth broadening of Josephson oscillations at mm and submm wave frequencies in high-Tc superconducting junctions. Experimental results are discussed in terms of bound states existing at surfaces of d-wave superconducting electrodes.
The first experimental data are presented on the observation of a response of a noise signal applied to a tunable-by-voltage high- T C Josephson mixer operating in a self-pumping mode within the frequency band of f = 750–970 GHz at ambient temperature T = 12.5 K. The mixer device was a thin-film YBaCuO bicrystal Josephson junction coupled with the electrodes patterned in log-periodic antenna. Experimental junctions exhibit RSJ-like I–V characteristics with a product of I C R N ≈ 2 mV ( I C is the critical current and R N is the normal state resistance). Down-converted signal response was examined at an intermediate frequency band within 1–2 GHz by means of the Fourier transform spectroscopy technique. Evaluated from Fourier transform spectrograms clear double-side band mixer response functions were registered at any of the fixed bias voltages in the range of V = 1.65–2.1 mV.
Modeling of a broadband receiving system based on a meander series of Josephson YBaCuO grain boundary junctions integrated into a log-periodic antenna was carried out. The electromagnetic properties of the system, namely amplitude–frequency characteristic, beam pattern, and fraction of the absorbed power in each Josephson junction were investigated. Based on the obtained results, a numerical simulation of one-dimensional arrays was carried out. The dc characteristics of the detector were calculated, that is, current–voltage characteristic, responsivity, noise, and noise-equivalent power (NEP) for a 250 GHz external signal. The optimal number of junctions to obtain the minimum NEP was found. The use of a series of junctions allows one to increase the responsivity by a factor of 2.5, the NEP value by a factor of 1.5, and the power dynamic range by a factor of 5. For typical YBaCuO Josephson junctions fabricated on a ZrYO bicrystal substrate by magnetron deposition, the following parameters were obtained at a temperature of 77 K: responsivity = 9 kV/W; NEP = 3·10−13 W/Hz(1/2); power dynamic range = 1·106.
An HTS Josephson spectrometer has been designed, fabricated and experimentally studied. The spectrometer circuit consists of a YBCO bicrystal Josephson junction integrated with a double-slot or log-periodic antenna, connected in parallel with a gold low-inductance shunt. The selective detector response and RF response at intermediate frequency f IF = 1.4 GHz were measured in the signal frequency range f s = 400-1250 GHz and the linewidth of Josephson oscillations (LJO) was determined by using three different methods. (1) The Hilbert spectroscopy approach was used in the processing of the selective detector response. (2) In case of f IF < LJO the detector and RF responses have similar shapes, allowing the spectrum and LJO to be extracted from the RF response and even processing by modified Hilbert spectroscopy. (3) The RF response at f IF > LJO corresponds to the frequency down-conversion in a self-pumped Josephson mixer mode. For the processing of the RF response in the high f IF limit we suggest a novel method that allows extraction of the signal spectrum by means of simple operations: shifting, summing and subtracting. The advantage of the RF response method is in its simplicity and higher sensitivity that allows it to be proposed for spectroscopy applications.
We prepared Josephson junctions made of YBa2Cu3O7 on symmetric 24° LaAlO3 bicrystal substrates. For better coupling of high-frequency radiation, we structured the contacts with logarithmic-periodic antennas made of YBa2Cu3O7. Characterization was done by measuring the voltage–current characteristics to determine the critical current IC, the normal-state resistance RN, the noise parameter Γ, and the Stewart–McCumber parameter βC as predicted by the resistively and capactively shunted junction model (RCSJ). The junctions showed excellent RCSJ-like behavior with ICRN products of up to 2.0 mV at 10 K and 220 μV at 77 K. To demonstrate the possibility to detect high-frequency radiation up to the THz regime, we used the Josephson junction as a detector for radiation from a far-infrared laser and we reconstructed the spectra by Hilbert spectroscopy.