We have developed a method of designing single-flux-quantum (SFQ) logic circuits with passive gate-to-gate interconnections. Based on our method, we designed a 2/spl times/2 switch in which all the interconnections are implemented with passive transmission lines (PTLs) while short Josephson transmission line (JTL) segments are used only to adjust the signal timings. Compared with an identical switch using JTL interconnections, the switch using PTL interconnections has 45% fewer wiring junctions and requires 48% less wiring power current. The switch operated at 40 GHz with a bias margin of /spl plusmn/9.5%.
We have developed a method of designing single-flux-quantum (SFQ) logic circuits with passive gate-to-gate interconnections. Based on our method, we designed a 2/spl times/2 switch in which all the interconnections are implemented with passive transmission lines (PTLs) while short Josephson transmission line (JTL) segments are used only to adjust the signal timings. Compared with an identical switch using JTL interconnections, the switch using PTL interconnections has 45% fewer wiring junctions and requires 48% less wiring power current. The switch operated at 40 GHz with a bias margin of /spl plusmn/9.5%.
To enable the use of passive transmission lines (PTLs) for the interconnection of single-flux-quantum (SFQ) circuits, we have implemented a driver and a receiver and have developed a method for designing SFQ circuits with passive interconnections. Basic components and properties of passive interconnections, such as the frequency characteristics of the driver and receiver, the PTL delay, and the crosstalk between PTLs, have been experimentally verified. Our developed components and design method have been applied to actual SFQ circuits, such as a 4 x 4 switch having block-to-block passive interconnections and a 2 x 2 switch having gate-to-gate passive interconnections. We have also shown the advantages of PTLs over Josephson transmission lines (JTLs). We also discuss the prospects of SFO circuits having passive interconnections.
We developed a design approach for interface circuits to connect Single Flux Quantum (SFQ) cells by using passive transmission lines (PTL's). In the approach, an interface circuit between a PTL and JTL is optimized to obtain a standard interface circuit, and then, modifications are made to previously designed SFQ cells and the standard interface circuit to connect the SFQ cells by using PTL's. The key point is the use of approximately the same interface circuit with every SFQ cell to maintain the matching condition between the interface circuit and the PTL's. Based on this approach, we designed an interface circuit and a test circuit composed of two D-flip-flops connected using 2-mm-long PTL's via the interface circuits. The impedance of the PTL was 2 /spl Omega/. We achieved high-speed operation of the test circuit up to 35 GHz with a bias margin of -15/+30%.
The introduction of passive-transmission-line (PTL) wiring to large-scale SFQ logic circuits offers several advantages over traditional Josephson-transmission-line (JTL) wiring, such as smaller wiring area, less delay, lower power consumption, and more freedom in routing. PTL wiring can drastically change the style of designing SFQ logic circuits. We propose a new methodology for designing large-scale SFQ circuits using PTL wiring. Aiming at generalizing SFQ circuit design, we chose synchronous clocking. We developed a placer that was suitable for SFQ circuit design to assist us with the new design methodology. The placer first synthesizes an H-tree clock distribution network, placing SFQ pulse splitter cells at each branch. It then places logic cells to minimize the maximum length of data PTL wires, aiming at higher operating speeds. Finally, a router completes the PTL wiring. To evaluate the design methodology we designed an 8-bit general purpose RISC processor. Within twelve hours, we obtained a 15-mm-square SFQ circuit that could operate up to 27.6 GHz. We adopted an advanced Nb process, which was characterized by a critical current density of 10 kA/cm2, two 5-mum-wide PTL wiring layers, and a minimum cell size of 30 mum times 30 mum. The circuit consisted of about 20,000 logic cells, which approximated more than 400,000 Josephson junctions including splitters to distribute the clock signal.
The increasing complexity of modern rapid single flux quantum (RSFQ) circuits has made on-chip signal routing, an issue of growing importance. In this paper, several methods for routing large-scale RSFQ circuits are described, and a process is presented for determining when to use passive microstrip transmission lines (PTL) and active Josephson transmission lines (JTL). The effect of the size of the JTL inductor and Josephson junctions on the length of a JTL chain for a target delay is also discussed. The dependence of the JTL inductance on the physical layout is evaluated, and the effects of the primary PTL parameters on delay are characterized. A novel PTL driver and receiver configuration is also proposed. Tradeoffs among the number of JJs, inductance, and length of a PTL stripline in the receiver and driver circuits are reported. The energy dissipation is evaluated for two different interconnects. A tradeoff between the proposed PTL circuits and an optimized JTL in terms of energy dissipation and delay is discussed. Guidelines for choosing the optimal element values are determined, and a simulated bias margin of ±29% for the bias current of the proposed receiver operating at 20 GHz in a 10 kA/cm2technology for a 1-mm transmission line is achieved. Summarizing, guidelines and design tradeoffs appropriate for automated layout and synthesis are provided for driving long interconnect in SFQ VLSI circuits.
We have been developing a single-flux-quantum (SFQ) cross-bar switch, which is a main component of a network packet switch. We think that a network switch is an application in which the high speed of SFQ technology would be advantageous. Anticipating general and large-scale SFQ logic circuit design, we used the cell-based design method and the CONNECT standard SFQ cell library. The two-input and two-output cross-bar switch, a core switch component, consists of 13 logic cells connected by Josephson-transmission-line (JTL) cells. Because of the large size of JTL cells and the large delay in them, timing adjustment becomes more difficult as the operating speed and circuit size increase. After using a commercially available automatic router to find appropriate routes efficiently, we used a static timing analyzer for fine timing adjustment. Timing violations were fixed by changing JTL path delays using the tools we developed. The target operating frequency of the switch was 40 GHz, which corresponds to a clock period of 25 ps. Careful timing adjustment was necessary to ensure correct operations at such a high speed. The test chip was fabricated by using an NEC standard Nb process. The circuit, including on-chip test circuitry, was composed of about 1500 Josephson junctions. We confirmed its correct operations up to 50 GHz with a bias margin of /spl plusmn/20%.
Superconductive passive transmission lines (PTL) are widely used for signal routing in large-scale rapid single flux quantum (RSFQ) circuits. Due to the imperfect matching of the transmission lines between the driver and receiver, single flux quantum (SFQ) pulses are partially reflected. The round trip propagation time of these reflections can coincide with the following SFQ pulse, resulting in a decrease in bias margins or incorrect circuit behavior. This resonant effect depends upon the length of the PTL and the clock frequency of the signal. A methodology to reduce and manage this effect is the focus of this article. A closed-form expression describing the dependence of the resonance frequency on the length of the PTL is presented. This expression describes a set of forbidden lengths for PTL interconnect segments in RSFQ circuits. The proposed methodology and algorithm insert active PTL-based repeaters into long superconductive interconnect while ensuring the length of the line segment is outside the forbidden region and increasing bias margins.