IEEE Transactions on Applied Superconductivity

Aluminum hot-electron bolometer mixers at submillimeter wavelengths

Anders J. Skalare, William R. McGrath, P. M. Echternach, Henry George LeDuc, Irfan A. Siddiqi, A. Verevkin, D. E. Prober

Published Mar 1, 2001• 17 citations

Publisher

Abstract

Diffusion-cooled aluminum hot-electron bolometer (HEB) mixers are of interest for low-noise high resolution THz-frequency spectroscopy within astrophysics. Al HEB mixers offer operation with an order of magnitude less local oscillator power, higher intermediate frequency bandwidth and potentially lower noise than competing devices made from other materials. We report on mixer experiments at 618 GHz with devices fabricated from films with sheet resistances in the range from about 55 /spl Omega/ down to about 9 /spl Omega/ per square. Intermediate frequency bandwidths of up to 3 GHz were measured (1 /spl mu/m long device), with absorbed local oscillator power levels of 0.5 to 6 nW and mixer conversion up to -21.5 dB. High input coupling efficiency implies that the electrons in the device are able to thermalize before escaping from the device. It was found that the long coherence length complicates mixer operations due to the proximity of the contact pads. Also, saturation at the IF frequency may be a concern for this type of device, and warrants further studies.

DOI: 10.1109/77.919426

Related papers

Noise and conversion efficiency of aluminum superconducting hot-electron bolometer mixer

Irfan A. Siddiqi, A. Verevkin, D. E. Prober +5 more

We report on microwave measurements of superconducting aluminum hot-electron bolometers (Al HEBs). Diffusion-cooled Al HEB mixers are good candidates for space-borne applications in the Terahertz frequency range since they are predicted to have small local oscillator (LO) power requirements, intermediate frequency (IF) bandwidths /spl gsim/10 GHz, and a noise temperature lower than that of Nb and NbN HEB mixers. Mixer measurements were made at an LO frequency /spl sim/30 GHz, with an IF in the range 0.1 to 7.3 GHz. For T<0.8 K, a magnetic field H=0.1-0.3 T was applied to suppress the superconductivity in the contact pads, and partly in the bridge. For a 0.6 /spl mu/m long device, we measure an IF bandwidth of 4 GHz, a conversion efficiency /spl eta/=-8 dB, and a mixer noise temperature T/sub M//spl gsim/4 K, DSB (T/sub mixer/=T/sub output noise//2/spl eta/). These results are shown to be in quantitative agreement with simple theoretical predictions.

IEEE Transactions on Applied SuperconductivityMar 1, 200117 citations

Low-noise and wideband hot-electron superconductive mixers for THz frequencies

Boris S. Karasik, Anders J. Skalare, Rolf A. Wyss +5 more

Superconductive hot-electron bolometer (HEB) mixers have been built and tested in the frequency range 1.1-2.5 THz. The mixer device is a 0.15-03 /spl mu/m microbridge made from a 10 nm thick Nb film. This device employs diffusion as a cooling mechanism for hot electrons. The double sideband noise temperature was measured to be /spl les/3000 K at 2.5 THz and the mixer IF bandwidth is /spl ap/9-10 GHz for a 0.1 /spl mu/m long device. The local oscillator (LO) power dissipated in the HEB microbridge was 20-100 nW. Further improvement of the mixer characteristics can be potentially achieved by using Al microbridges. The advantages and parameters of such devices are evaluated The HEB mixer Is a primary candidate for ground based, airborne and spaceborne heterodyne instruments at THz frequencies. HEB receivers are planned for use on the NASA Stratospheric Observatory for Infrared Astronomy (SOFIA) and the ESA Far Infrared and Submillimeter Space Telescope (FIRST). The prospects of a submicron-size YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// (YBCO) HEB are also discussed. The expected LO power of 1-10 /spl mu/W and SSB noise temperature of /spl ap/2000 K may make this mixer attractive for various remote sensing applications.

IEEE International Conference on Terahertz Electronics (THz)Nov 27, 20025 citations

Aluminum Sub-Micron Superconducting Hot-Electron Bolometer Mixer

Irfan A. Siddiqi, A. Verevkin, D. E. Prober +5 more

We report on microwave measurements of superconducting aluminum hot-electron bolometers (Al HEBs). Diffusion-cooled Al HEB mixers are ideal candidates for space-borne and terrestrial remote-sensing applications in the Terahertz frequency range since they are predicted to have small local oscillator (LO) power requirements, intermediate frequency (IF) bandwidths ! 10 GHz, and a noise temperature lower than that of Nb and NbN HEBs. Mixer measurements were made at an LO frequency ~30 GHz LO, with an IF in the range 0.1-7.3 GHz. For T < 0.8 K, a magnetic field H=0.1-0.3T was applied to suppress the superconductivity in the contact pads, and partly in the bridge. For a 0.6 μm long Al HEB, we measure an IF bandwidth of 4 GHz, a conversion efficiency η = -8dB, and a mixer noise temperature Tm ! 4K, DSB (Tmixer=Toutput noise/2η). These results are shown to be in quantitative agreement with simple theoretical predictions.

Softwaretechnik-TrendsMay 1, 20003 citations

Noise and Bandwidth Measurements of Diffusion-Cooled Nb Hot-Electron Bolometer Mixers at Frequencies Above the Superconductive Energy Gap

Rolf A. Wyss, Boris S. Karasik, William R. McGrath +2 more

Diffusion-cooled Nb hot-electron bolometer (HEB) mixers have the potential to simultaneously achieve high intermediate frequency (IF) bandwidths and low mixer noise temperatures for operation at THz frequencies (above the superconductive gap energy). We have measured the IF signal bandwidth at 630 GHz of Nb devices with lengths L = 0.3, 0.2, and 0.1 micrometer in a quasioptical mixer configuration employing twin-slot antennas. The 3-dB EF bandwidth increased from 1.2 GHz for the 0.3 gm long device to 9.2 GHz for the 0.1 gm long device. These results demonstrate the expected 1/L squared dependence of the IF bandwidth at submillimeter wave frequencies for the first time, as well as the largest EF bandwidth obtained to date. For the 0.1 gm device, which had the largest bandwidth, the double sideband (DSB) noise temperature of the receiver was 320-470 K at 630 GHz with an absorbed LO power of 35 nW, estimated using the isothermal method. A version of this mixer with the antenna length scaled for operation at 2.5 THz has also been tested. A DSB receiver noise temperature of 1800 plus or minus 100 K was achieved, which is about 1,000 K lower than our previously reported results. These results demonstrate that large EF bandwidth and low-noise operation of a diffusion-cooled HEB mixer is possible at THz frequencies with the same device geometry.

Softwaretechnik-TrendsJan 1, 199920 citations

Low-noise and wideband hot-electron superconductive mixer for terahertz frequencies

Boris S. Karasik, Anders J. Skalare, William R. McGrath +7 more

Superconductive hot-electron bolometer (HEB) mixers have been built and tested in the frequency range from 1.1 THz to 2.5 THz. The mixer device is a 0.15 - 0.3 micrometer microbridge made from a 10 nm thick Nb film. This device employs diffusion as a cooling mechanism for hot electrons. The double sideband noise temperature was measured to be less than or equal to 3000 K at 2.5 THz and the mixer IF bandwidth is expected to be at least 10 GHz for a 0.1 micrometer long device. The local oscillator (LO) power dissipated in the HEB microbridge was 20 - 100 nW. Further improvement of the mixer characteristics can be potentially achieved by using Al microbridges. The advantages and parameters of such devices are evaluated. The HEB mixer is a primary candidate for ground based, airborne and spaceborne heterodyne instruments at THz frequencies. HEB receivers are planned for use on the NASA Stratospheric Observatory for Infrared Astronomy (SOFIA) and the ESA Far Infrared and Submillimeter Space Telescope (FIRST). The prospects of a submicron-size YBa2Cu3O7-(delta ) (YBCO) HEB are discussed. The expected LO power of 1 - 10 (mu) W and SSB noise temperature of approximately equals 2000 K may make this mixer attractive for various remote sensing applications.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIENov 13, 19981 citation

Heterodyne mixing in diffusion-cooled superconducting aluminum hot-electron bolometers

Irfan A. Siddiqi, A. Verevkin, D. E. Prober +4 more

We present microwave (30 GHz) measurements on aluminum superconducting hot-electron bolometer (HEB) mixers. Aluminum HEB mixers have a lower superconducting transition temperature than niobium and niobium nitride devices, and are predicted to have improved sensitivity and require less local oscillator power. The devices studied consist of a narrow superconducting aluminum microbridge with contacts comprised of thick aluminum, titanium, and gold. A perpendicular magnetic field is used to suppress superconductivity in the contacts. The device length is much shorter than the electron–phonon inelastic length [L≪(Dτe–ph)1/2] and thus the intermediate frequency (IF) bandwidth is set by the diffusion time of hot electrons from the microbridge into the contacts. We discuss limitations on the IF bandwidth in very short HEB mixers with fully normal contacts. Overall, the microwave heterodyne mixing results show good performance with a mixer noise temperature inferred from the conversion efficiency and output noise of TM⩾4 K, double side band (DSB). Measurements at 618 GHz yield a conversion efficiency approximately 10 dB lower than observed at 30 GHz. Output saturation by background radiation is postulated to contribute significantly to this difference. A similar decrease in conversion efficiency in the microwave mixing measurements is observed when broadband noise is added to the rf input signal. We discuss the tradeoff between increased sensitivity and the occurrence of saturation effects in low transition temperature HEBs.

Journal of Applied PhysicsApr 1, 200213 citations