Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Temperature dependence of the Josephson linewidth of resistively shunted double junction HTS SQUIDs

D.A. Peden, L. Hao, J.C. Macfarlane, R.A.M. Lee, John C. Gallop

Published Mar 1, 2001• 0 citations
Publisher

Abstract

Double Josephson junction HTS resistive SQUIDs have been fabricated using an on-chip shunt Au resistor across a gap in an YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// loop, providing a low shunt resistance of R/sub s/ /spl sim/26 /spl mu//spl Omega/ at T/spl les/77 K. The dependence of the heterodyne oscillation linewidth of the R-SQUID on the thermal noise across the shunt resistor is under investigation with a view to the development of an absolute noise thermometer. Signal powers /spl sim/nW have been measured and the device has been shown to be tunable from 5 to 50 MHz. The measured oscillation linewidth (/spl sim/30 kHz at 17 K) is believed to be the narrowest reported for such an HTS device, however non-thermal broadening of the linewidth is also observed, as has been reported for single junctions at GHz frequencies. We describe measurements on such devices over a range of temperatures and bias conditions.

DOI
10.1109/77.919568

Related papers

Linewidth of a resistively shunted high-temperature-superconductor Josephson heterodyne oscillator

J.C. Macfarlane, L. Hao, D.A. Peden +1 more

High-temperature-superconducting (HTS) resistively shunted superconducting quantum interference devices, consisting of two yttrium–barium–copper–oxide (YBCO) grain boundary junctions shunted by gold-film resistors of ∼20 μΩ, have been prepared and characterized at temperatures from 17 to 74 K. The small value and stability of the resistor allows narrow-band heterodyne oscillations to be generated between the Josephson oscillations in the individual junctions. The frequency can be precisely controlled in accordance with the ac Josephson effect by adjustment of an external current applied to the YBCO–Au–YBCO shunt resistor, and the linewidth is determined in principle only by Johnson noise in the resistor. Off-chip detection and spectral analysis of the heterodyne signal generated in this way has not been previously reported. Measurements of the signal power (∼nW), the tunability of the center frequency from 5 to 50 MHz, the frequency stability and the linewidth of the heterodyne Josephson oscillation are described. Although linewidth broadening due to nonthermal fluctuations is observed, the linewidth of ∼30 kHz at T=17 K, at a center frequency of 24 MHz, is believed to be the narrowest reported for Josephson oscillations in an HTS device of this type.

Applied Physics Letters•Mar 27, 2000•14 citations

Tunable HTS rf Josephson-effect oscillator based on YBCO-Au-YBCO resistive SQUID

L Hao, D.A. Peden, John C. Gallop +1 more

We report the successful realization of a resistively shunted two-junction high temperature superconducting (HTS) SQUID in which the heterodyne signal generated between the two YBCO grain-boundary junctions is accurately controlled in the range of 1–50 MHz by adjustment of the bias current in the milliampere range through a thin-film on-chip YBCO-Au-YBCO shunt resistor (∼25 μΩ). Oscillations in the temperature range 20–60 K and signal powers up to 2 nW in a 20 kHz bandwidth have been recorded.

Superconductor Science and Technology•Nov 21, 2001•5 citations

Simulation and Measurement of HTS Josephson Heterodyne Oscillator

J.C. Macfarlane, Jia Du, Richard Taylor +1 more

We report continuing investigations into practical applications of the AC Josephson effect as the basis for a voltage-tunable radio-frequency oscillator. We have previously demonstrated experimentally that useful power levels (10 s of nW) and linewidths of a few kHz can be achieved in the heterodyne output from a high-temperature-superconducting resistive SQUID (HTS-RSQUID) operating in the frequency range 1-50 MHz. Those results were achieved with 2-junction R-SQUIDs incorporating current-biased shunt resistors of a few micro-ohms. We have now modified the fabrication procedures, and adjusted the shunt resistors and bias current values so that higher frequencies can be achieved. The Josephson junctions are of step-edge type, rather than the bi-crystal type used in our earlier work. The step-edge technique permits much more flexibility in the geometrical lay-out and utilizes the more cost-effective single-crystal MgO substrates. In the present paper, we report numerical simulations and experimental measurements on these devices in the frequency range up to 2 GHz.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•17 citations

Linewidth of Josephson oscillations in YBa/sub 2/Cu/sub 3/O/sub 7-x/ grain-boundary junctions

Yu. Ya. Divin, J. Mygind, N. F. Pedersen +1 more

The AC Josephson effect in YBa/sub 2/Cu/sub 3/O/sub 7-x/ grain-boundary junctions (GBJs) was studied in the temperature range from 4 K to 90 K. The temperature dependence of the linewidth of millimeter-wave Josephson oscillations was measured, and it is shown that the derived effective noise temperature of GBJ might be as low as the physical temperature in the temperature range investigated. This makes it possible to use the resistively shunted junction (RSJ) model with thermal fluctuations to get a limiting performance of high-T/sub c/ devices utilizing the AC Josephson effect. The lowest value of the linewidth of 72 GHz Josephson oscillations observed at 77 K was equal to 380 MHz, which demonstrates the applicability of GBJ, particularly in the field of radiation spectroscopy, even at liquid nitrogen temperatures.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•7 citations

Self-pumped HTS Josephson heterodyne tunable mixer

Jia Du, J.C. Macfarlane, Ting Zhang +2 more

Experimental evaluation of a high-temperature superconducting Josephson heterodyne mixer based on a 'resistive-SQUID' configuration is reported. The device consists of two YBa 2 Cu 3 O 7− x step-edge Josephson junctions connected via a small resistor in an otherwise superconducting loop. It has been previously shown to generate a heterodyne oscillation, which is frequency-tunable by a control current through the resistor. Under certain conditions, this device can operate as a frequency-tunable heterodyne mixer (down-converter) in the presence of an RF signal. In this paper, we describe the operation of the autonomous Josephson mixer–local oscillator device and present the experimental results on the mixer performances in terms of the junction current–voltage characteristics, the frequency tunability, linearity, and dynamic range as well as their temperature dependence for signal frequencies from 1 to 5 GHz.

Superconductor Science and Technology•Jan 10, 2012•16 citations

Submillimeter-wave mixing and noise in HTS Josephson junctions

Michael A. Tarasov, Е. А. Степанцов, Dmitry S. Golubev +6 more

A Josephson quasioptical detector comprising YBaCuO junction on bicrystal MgO substrate, integrated log-periodic Au antenna, MgO extended hyperhemisphere lens attached to the substrate and 1.4 GHz cold amplifier with cold circulator has been designed, fabricated and experimentally studied. We fabricated several integrated Josephson junctions 1-2 /spl mu/m wide which at 4.2 K demonstrate RSJ IV curves with critical currents 100-300 /spl mu/A and normal resistance of 10-20 /spl Omega/. The noise temperature (T/sub N/) at 4.2 K and 330 GHz measured by a hot/cold load method in fundamental mixing mode with external BWO local oscillator brings T/sub N/=1100 K for the junction shunted by low-inductance resistive shunt and T/sub N/=1400 K without shunting. At bath temperatures of 20-40 K the noise temperature was in the range 1500-3000 K, at 50 K the noise temperature was below 2000 K, and at 60-70 K increased over 3000 K in the frequency range 310-586 GHz. The noise temperatures measured in the self-pumping mode vary between 580-2300 K with dc bias in the range 0.1-0.5 mV. The linewidth of Josephson oscillations has been extracted from a selective detector response and IF noise voltage dependence. The measured excess noise can be attributed to shot noise and multiple Andreev reflection in pinholes with Ss'S structure. We observed small subharmonic steps in IV curve and noise dependencies, which are typical for SNS junctions.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•8 citations
Double Josephson junction HTS resistive SQUIDs have been fabricated using an on-chip shunt Au resistor across a gap in an YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// loop, providing a low shunt resistance of R/sub s/ /spl sim/26 /spl mu//spl Omega/ at T/spl les/77 K. The dependence of the heterodyne oscillation linewidth of the R-SQUID on the thermal noise across the shunt resistor is under investigation with a view to the development of an absolute noise thermometer. Signal powers /spl sim/nW have been measured and the device has been shown to be tunable from 5 to 50 MHz. The measured oscillation linewidth (/spl sim/30 kHz at 17 K) is believed to be the narrowest reported for such an HTS device, however non-thermal broadening of the linewidth is also observed, as has been reported for single junctions at GHz frequencies. We describe measurements on such devices over a range of temperatures and bias conditions.
High-temperature-superconducting (HTS) resistively shunted superconducting quantum interference devices, consisting of two yttrium–barium–copper–oxide (YBCO) grain boundary junctions shunted by gold-film resistors of ∼20 μΩ, have been prepared and characterized at temperatures from 17 to 74 K. The small value and stability of the resistor allows narrow-band heterodyne oscillations to be generated between the Josephson oscillations in the individual junctions. The frequency can be precisely controlled in accordance with the ac Josephson effect by adjustment of an external current applied to the YBCO–Au–YBCO shunt resistor, and the linewidth is determined in principle only by Johnson noise in the resistor. Off-chip detection and spectral analysis of the heterodyne signal generated in this way has not been previously reported. Measurements of the signal power (∼nW), the tunability of the center frequency from 5 to 50 MHz, the frequency stability and the linewidth of the heterodyne Josephson oscillation are described. Although linewidth broadening due to nonthermal fluctuations is observed, the linewidth of ∼30 kHz at T=17 K, at a center frequency of 24 MHz, is believed to be the narrowest reported for Josephson oscillations in an HTS device of this type.
We report the successful realization of a resistively shunted two-junction high temperature superconducting (HTS) SQUID in which the heterodyne signal generated between the two YBCO grain-boundary junctions is accurately controlled in the range of 1–50 MHz by adjustment of the bias current in the milliampere range through a thin-film on-chip YBCO-Au-YBCO shunt resistor (∼25 μΩ). Oscillations in the temperature range 20–60 K and signal powers up to 2 nW in a 20 kHz bandwidth have been recorded.
We report continuing investigations into practical applications of the AC Josephson effect as the basis for a voltage-tunable radio-frequency oscillator. We have previously demonstrated experimentally that useful power levels (10 s of nW) and linewidths of a few kHz can be achieved in the heterodyne output from a high-temperature-superconducting resistive SQUID (HTS-RSQUID) operating in the frequency range 1-50 MHz. Those results were achieved with 2-junction R-SQUIDs incorporating current-biased shunt resistors of a few micro-ohms. We have now modified the fabrication procedures, and adjusted the shunt resistors and bias current values so that higher frequencies can be achieved. The Josephson junctions are of step-edge type, rather than the bi-crystal type used in our earlier work. The step-edge technique permits much more flexibility in the geometrical lay-out and utilizes the more cost-effective single-crystal MgO substrates. In the present paper, we report numerical simulations and experimental measurements on these devices in the frequency range up to 2 GHz.
The AC Josephson effect in YBa/sub 2/Cu/sub 3/O/sub 7-x/ grain-boundary junctions (GBJs) was studied in the temperature range from 4 K to 90 K. The temperature dependence of the linewidth of millimeter-wave Josephson oscillations was measured, and it is shown that the derived effective noise temperature of GBJ might be as low as the physical temperature in the temperature range investigated. This makes it possible to use the resistively shunted junction (RSJ) model with thermal fluctuations to get a limiting performance of high-T/sub c/ devices utilizing the AC Josephson effect. The lowest value of the linewidth of 72 GHz Josephson oscillations observed at 77 K was equal to 380 MHz, which demonstrates the applicability of GBJ, particularly in the field of radiation spectroscopy, even at liquid nitrogen temperatures.>
Experimental evaluation of a high-temperature superconducting Josephson heterodyne mixer based on a 'resistive-SQUID' configuration is reported. The device consists of two YBa 2 Cu 3 O 7− x step-edge Josephson junctions connected via a small resistor in an otherwise superconducting loop. It has been previously shown to generate a heterodyne oscillation, which is frequency-tunable by a control current through the resistor. Under certain conditions, this device can operate as a frequency-tunable heterodyne mixer (down-converter) in the presence of an RF signal. In this paper, we describe the operation of the autonomous Josephson mixer–local oscillator device and present the experimental results on the mixer performances in terms of the junction current–voltage characteristics, the frequency tunability, linearity, and dynamic range as well as their temperature dependence for signal frequencies from 1 to 5 GHz.
A Josephson quasioptical detector comprising YBaCuO junction on bicrystal MgO substrate, integrated log-periodic Au antenna, MgO extended hyperhemisphere lens attached to the substrate and 1.4 GHz cold amplifier with cold circulator has been designed, fabricated and experimentally studied. We fabricated several integrated Josephson junctions 1-2 /spl mu/m wide which at 4.2 K demonstrate RSJ IV curves with critical currents 100-300 /spl mu/A and normal resistance of 10-20 /spl Omega/. The noise temperature (T/sub N/) at 4.2 K and 330 GHz measured by a hot/cold load method in fundamental mixing mode with external BWO local oscillator brings T/sub N/=1100 K for the junction shunted by low-inductance resistive shunt and T/sub N/=1400 K without shunting. At bath temperatures of 20-40 K the noise temperature was in the range 1500-3000 K, at 50 K the noise temperature was below 2000 K, and at 60-70 K increased over 3000 K in the frequency range 310-586 GHz. The noise temperatures measured in the self-pumping mode vary between 580-2300 K with dc bias in the range 0.1-0.5 mV. The linewidth of Josephson oscillations has been extracted from a selective detector response and IF noise voltage dependence. The measured excess noise can be attributed to shot noise and multiple Andreev reflection in pinholes with Ss'S structure. We observed small subharmonic steps in IV curve and noise dependencies, which are typical for SNS junctions.