Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)
Superconducting single photon detectors
Sae Woo Nam, Brice Calkins, T. Gerritts, Sean David Harrington, Adriana E. Lita, Francesco Marsili, Varun Boehm Verma, Igor Vayshenker, Richard P. Mirin, Matthew D. Shaw, William H. Farr, J. A. Stern
There is increasing interest in using superconducting optical photon detectors in a variety of applications. These applications require detectors that have extremely low dark count rates, high count rates, and high quantum efficiency. I will describe our work on two types of superconducting detectors, the Superconducting Nanowire Single Photon Detector (SNSPD or nSSPD) and superconducting Transition-Edge Sensor (TES). An SNSPD is an ultra-thin, ultra-narrow (nm scale) superconducting meander that is current biased just below its critical current density. When one or more photon is absorbed, a hot spot is formed that causes the superconductor to develop a resistance and consequently a voltage pulse. At NIST and JPL, we have been developing nanowire detectors using an amorphous alloy of tungsten-silicide. An example of this detector is shown in Fig 1(a). In this case, there are two tungsten silicide layers separated by a dielectric layer to optimize detection of light for any polarization[1]. Fig 1(b) is an example of a TES detector with gold cooling fins to enhance timing of the detector[2]. By exploiting the sharp superconducting-to-normal resistive transition of tungsten at 100mK, TES detectors give an output signal that is proportional to the cumulative energy in an absorption event. This proportional pulse-height enables the determination of the energy absorbed by the TES and the direct conversion of sensor pulse-height into photon number. I will discuss our progress towards developing both types of detectors with quantum efficiencies approaching 100%.
There is increasing interest in using superconducting optical photon detectors in a variety of applications. These applications require detectors that have extremely low dark count rates, high count rates, and high quantum efficiency. I will describe our work on two types of superconducting detectors, the Superconducting Nanowire Single Photon Detector (SNSPD or nSSPD) and superconducting Transition-Edge Sensor (TES). An SNSPD is an ultra-thin, ultra-narrow (nm scale) superconducting meander that is current biased just below its critical current density. When one or more photon is absorbed, a hot spot is formed that causes the superconductor to develop a resistance and consequently a voltage pulse. At NIST and JPL, we have been developing nanowire detectors using an amorphous alloy of tungsten-silicide. An example of this detector is shown in Fig 1(a). In this case, there are two tungsten silicide layers separated by a dielectric layer to optimize detection of light for any polarization[1]. Fig 1(b) is an example of a TES detector with gold cooling fins to enhance timing of the detector[2]. By exploiting the sharp superconducting-to-normal resistive transition of tungsten at 100mK, TES detectors give an output signal that is proportional to the cumulative energy in an absorption event. This proportional pulse-height enables the determination of the energy absorbed by the TES and the direct conversion of sensor pulse-height into photon number. I will discuss our progress towards developing both types of detectors with quantum efficiencies approaching 100%.
Superconducting devices offer the potential to perform at speeds and detection efficiencies higher than what is possible using conventional technologies (such as semiconducting avalanche photodiodes and photomultiplier tubs) for wavelengths from the ultraviolet to the mid-infrared. As a result, there has been increasing interest in using superconducting optical photon detectors in a variety of applications. There has been significant progress in using these types of detectors in areas of basic research such as quantum information science and quantum optics. These applications require detectors that have extremely low dark count rates, high count rates, and high quantum efficiency. I will begin by describing some of our earlier work on superconducting Transition-Edge Sensor (TES). In particular, I will describe some of the engineering involved in the cryogenic, electrical, and optical packaging so that these devices can be easily coupled into fiber-based optics. I will also describe our recent work on developing superconducting nanowire single photon detectors (SNSPD or SSPD). An SNSPD is an ultra-thin, ultra-narrow (nm scale) superconducting meander that is current biased just below its critical current density. When one or more photon is absorbed, a hot spot is formed that causes the superconductor to develop a resistance and consequently a voltage pulse. At NIST and JPL, we have been developing nanowire detectors using an amorphous alloy of tungsten-silicide. We will describe to construct systems using tungsten-silicide nanowires to achieve high detection efficiency (>90% at 1550nm). I will also describe our work to improve the performance of the device by fabricating multiple nanowires in an electrically parallel structure to implement a superconducting nanowire avalanche photodiode (SNAP)[1]. One example of this type of detector is shown in Fig 1. In this case, there are two tungsten silicide layers separated by a dielectric layer to optimize detection of light for any polarization[2]. In addition, progress on other types of SNAP detectors will be described to increase the signal size from a single photon, reduce the recovery time of the device, and to improve the jitter.
Superconducting single-photon detectors have been shown to have extremely high detection efficiency over a large wavelength range, typically exceeding 90 % [1, 2]. Their use in quantum and classical optics is becoming more and more widespread in part due to improvements to and ease of use of the cryogenic packaging. In this talk, we will review two superconducting detector technologies, the superconducting nanowire single-photon detector (SNSPD) and the optical transition-edge sensor (TES) [3], that are being developed at NIST. We will also describe their applications in quantum and classical optics and present our recent effort to use these detectors as calibration standards, as well as our effort to establish a single-photon detector calibration service. Superconducting Nanowire Single Photon Detectors The SNSPD is based on a meandering, narrow, thin superconducting nanowire, current-biased close to its critical current. Our SNSPDs operate at temperatures around 1K. When a photon is absorbed in the detection region, the energy deposited drives the wire normal and a voltage pulse can be observed. Due to the speed of the detection process, the SNSPD offers high timing resolution along with detection of the photon flux at the shot-noise limit. The combination of both these features yields a detector that can measure the photon’s arrival time from a faint object or source. SNSPDs also offer single-photon detection capability beyond the wavelength detection range of silicon and InGaAs, out to at least 5000 nm [4]. SNSPDs were also recently implemented in an 8×8-pixel array enabling low-resolution, real-time imaging [5]. For our calibration service effort, we built an SNSPD system that can be used as a transfer standard between labs for single-photon detector calibrations. Transition Edge Sensors In contrast to the SNSPD, the TES is a photon-number resolving detector that has almost unity detection efficiency. The TES consists of a superconducting thin film, voltage-biased so that its resistance is in the transition between the superconducting regime and the normal conducting regime. The steep slope of the resistive transition allows for small temperature changes to be measured. The TES is designed such that the absorption of a single photon increases the temperature of the superconducting film enough to discern the resulting signal from the TES system noise. Therefore, the TES needs to be electrically and thermally quiet and is generally operated at temperatures around 100 mK. Due to its energy resolving capability, the TES can be also used as a spectrally resolving single-photon detector with limited resolution [6]. The TES can also be operated as a cryogenic radiometer in combination with an electrical substitution method, and can, in principle, yield absolute calibration of optical powers on the order of a few tens of femtowatts [7]. References 1 A. E. Lita, A. J. Miller, and S. W. Nam, Opt. Express 16, 3032 (2008). 2 F. Marsili, et al., Nat Photon 7, 210 (2013). 3 R. Hadfield and G. Johansson, Superconducting Devices in Quantum Optics (Springer, 2016). 4 F. Marsili, et al., in CLEO: 2013 (OSA, San Jose, California, 2013), p. CTu1H.1. 5 M. S. Allman, et al., Applied Physics Letters 106, 192601 (2015). 6 M. Fortsch, et al., Journal of Optics 17, 065501 (2015). 7 N. A. Tomlin, J. H. Lehman, and S. Nam, Optics Letters 37, 2346 (2012).
Superconducting nanowire single-photon detectors (SNSPD) are used in quantum optics when record-breaking time resolution, high speed, and exceptionally low levels of dark counts (false readings) are required. Their detection efficiency is limited, however, by the absorption coefficient of the ultrathin superconducting film for the detected radiation. One possible way of increasing the detector absorption without limiting its broadband response is to make a detector in the form of several vertically stacked layers and connect them in parallel. For the first time we have studied single-photon detection in a multilayer structure consisting of three superconducting layers of amorphous tungsten silicide (WSi) separated by thin layers of amorphous silicon. Two operating modes of the detector are illustrated: an avalanche regime and an arm-trigger regime. A shift in these modes occurs at currents of ∼0.5–0.6 times the critical current of the detector.
Abstract Superconducting Nanowire Single-Photon Detectors (SNSPDs) are key building blocks for photonic quantum technologies due to their ability to detect single photons with ultra-high efficiency, low dark counts and fast temporal resolution. Superconducting materials exhibiting high uniformity, large absorption cross-section and atomic-scale thickness are desirable to extend single-photon detection from the near-infrared up to the terahertz regime, where existing material choices are especially constrained. Substrate independence would further open the way to integrating detectors onto functional materials and heterostructures, enhancing performance and enabling proximal readout of a wide range of individual excitations. Here, we pattern the prototypical two-dimensional superconductor niobium diselenide (NbSe 2 ) into few-layer nanowires less than 100 nm wide and demonstrate single-photon detection at 780 nm and 1550 nm. At the same time, the dark-count rate remains below 1 Hz up to the switching current and we achieve a timing jitter below 50 ps. We estimate via a diffusive hot-spot model that materials and geometric parameters would allow a theoretical cut-off wavelength in the millimetre range, assuming state-of-the-art device parameters. Our results open up routes toward quantum-limited detectors integrated into quantum-photonic circuits and quantum devices, with the potential for novel detection capabilities and unprecedented energy sensitivity.
Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.