The application of superconducting (SQUID) galvanometers as low-noise preamplifiers with considerable bandwidth is explored. The important role of negative feedback in maximizing the bandwidth of these preamplifiers is carefully analyzed. Also discussed is the design and construction of superconducting impedance matching transformers suitable for making the unexcelled noise characteristics of these amplifiers available over a wide range of source impedances. A working preamplifier is described which has exhibited a maximum bandwidth of 10 kHz and noise temperatures in the liquid helium temperature range or below for all source impedances up to a few ohms. The operating characteristics of this preamplifier are compared to the best conventional room temperature amplifiers and are found to be superior for source impedances less than ∼10 Ω.
The application of superconducting (SQUID) galvanometers as low-noise preamplifiers with considerable bandwidth is explored. The important role of negative feedback in maximizing the bandwidth of these preamplifiers is carefully analyzed. Also discussed is the design and construction of superconducting impedance matching transformers suitable for making the unexcelled noise characteristics of these amplifiers available over a wide range of source impedances. A working preamplifier is described which has exhibited a maximum bandwidth of 10 kHz and noise temperatures in the liquid helium temperature range or below for all source impedances up to a few ohms. The operating characteristics of this preamplifier are compared to the best conventional room temperature amplifiers and are found to be superior for source impedances less than ∼10 Ω.
We describe a low-noise, two-stage dc Superconducting QUantum Interference Device (SQUID) amplifier that is designed for applications requiring high bandwidth and dynamic range. The output signal of a low-noise SQUID in the input stage coherently modulates a series array of identical SQUIDs in the output stage via a common modulation line. The input stage is designed so its output signal does not produce multiple modulation periods in the output stage. The output stage is designed to have sufficient gain so the output noise is dominated by the amplified noise of the input SQUID and exceeds the noise of a preamplifier in the room temperature readout electronics. The SQUID amplifier may therefore be operated without flux modulation or any impedance matching network, resulting in a large dynamic range and high bandwidth.
User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.
Due to their superior noise performance, superconducting quantum interference devices (SQUIDs) are an attractive alternative to high electron mobility transistors for constructing ultra-low-noise microwave amplifiers for cryogenic use. We describe the use of a lumped element SQUID inductively coupled to a quarter wave resonator. The resonator acts as an impedance transformer and also makes it possible to accurately measure the input impedance and intrinsic microwave characteristics of the SQUID. We present a model for input impedance and gain, compare it to the measured scattering parameters, and describe how to use the model for the systematic design of low-noise microwave amplifiers with a wide range of performance characteristics.
An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.
We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.
We investigated and optimized the low-frequency noise characteristics of a preamplifier used for readout of direct current superconducting quantum interference devices (SQUIDs). When the SQUID output was detected directly using a room-temperature low-voltage-noise preamplifier, the low-frequency noise of a SQUID system was found to be dominated by the input current noise of the preamplifiers in case of a large dynamic resistance of the SQUID. To reduce the current noise of the preamplifier in the low-frequency range, we investigated the dependence of total preamplifier noise on the collector current and source resistance. When the collector current was decreased from 8.4 mA to 3 mA in the preamplifier made of 3 parallel SSM2220 transistor pairs, the low-frequency total voltage noise of the preamplifier (at 0.1 Hz) decreased by about 3 times for a source resistance of 30 Ω whereas the white noise level remained nearly unchanged. Since the relative contribution of preamplifier's input voltage and current noise is different depending on the dynamic resistance or flux-to-voltage transfer of the SQUID, the results showed that the total noise of a SQUID system at low-frequency range can be improved significantly by optimizing the preamplifier circuit parameters, mainly the collector current in case of low-noise bipolar transistor pairs.