Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Asia-Pacific Microwave Conference (APMC)

Measurement of the Direct-Detection Responses of a 500-GHz and a 660-GHz Waveguide Superconducting SIS Mixer

Jing Li, Ming-Jye Wang, Sheng‐Cai Shi, Hiroshi Matsuo

Published Mar 22, 2006• 1 citation
Publisher

Abstract

This paper presents the direct-detection responses of a 500-GHz and a 660-GHz waveguide superconducting SIS (superconductor-insulator-superconductor) mixer measured with a Fourier transform spectrometer (FTS). The two superconducting SIS mixers adopt the same type of junction tuning circuit (i.e., parallel connected twin SIS junctions), but are of different designs for the junction feed point where RF signals are coupled and then transmitted to the SIS junction tuning circuit and have different mixer design criteria. The experimental results are discussed in detail.

DOI
10.1109/apmc.2005.1606815

Related papers

Direct-detection characteristics of an 850-GHz Niobium-based superconducting SIS mixer

Qing Shi, Ming Yao, Jing Li +1 more

This paper presents the direct-detection responses of an 850GHz Niobium-based superconducting SIS (superconductor-insulator-superconductor) mixer measured with a Fourier transform spectrometer (FTS). The frequency response, current response rate, shot noise and equivalent noise power (NEP) of the SIS junction are calculated and analyzed. The experiment results are discussed in detail.

IEEE International Workshop on Electromagnetics: Applications and Student Innovation Competition•May 1, 2016•0 citations

Development of a 0.5-THz Waveguide NbN-Based SIS Mixer

Jing Li, Masanori Takeda, Zhen Wang +1 more

This paper mainly reports the development of a 0.5-THz waveguide SIS (superconductor – insulator – superconductor) mixer, which adopts twin NbN-based SIS junctions (NbN/AlN/NbN) connected in parallel. The 0.5-THz waveguide NbN SIS mixer is designed incorporating with a 51-μm thick MgO substrate and a waveguide mixer mount with no back-short cavity. Detailed simulation results, junction fabrication process and junction I-V characteristics are described. Preliminary FTS (Fourier Transform Spectrometer) measurement results will also be discussed.

International Conference on Microwave and Millimeter Wave Technology (ICMMT)•Apr 1, 2007•4 citations

Performance Characterization of a 600-700 GHz SIS Mixer

M. J. Wang, Rey Chin, Wenlei Shan +4 more

A 600-700GHz SIS mixer with the twin-junction tuning circuit has been designed and fabricated [1] The surface impedance of thin-film superconducting microstrip lines, based on Mattis-Bardeen theory [2], is included in the optimization of RF impedance matching. The receiver noise temperature measured in the frequency range of 630-660GHz is below 200K and the lowest receiver noise temperature of 181K is achieved at 656GHz. The FTS response of the SIS mixer shows a good RF coupling from 600GHz to 700GHz. Both the noise performance and the FTS response can be quantitatively described by numerical results using the quantum theory of mixing. Some detail considerations on the mixer model calculation, such as spreading inductance around the junction tuning structure and mixer's embedding impedance, are discussed. Introduction Nb-based superconductor-insulator-superconductor (SIS) mixers have been used very successfully in sub-mm wavelength detection. Their receiver noise temperature has reached to three times the quantum limit, —3 hfrkB, below the junction's gap frequency. However, at high frequency bands, Nb SIS mixers need to be designed carefully because the photon energy is close to or higher than the gap energy of Nb, A-1.4meV. When the frequency band covers the gap frequency of Nb, —670GHz, the RF loss of Nb superconducting transmission lines increases dramatically and the surface impedance has strong frequency dependence. Usually, the RF properties of a superconducting transmission line can be described by the Mattis-Bardeen theory [2] in good accuracy. From results reported so far [4-9], the best receiver noise temperature is close to 5 hi7kB in the band of 600-700GHz. Despite of the input loss contributed by the experimental setup, some other properties of SIS mixers should be taken into account. In this paper, we characterize the performance of a 600-700GHz mixer by comparing the experimental and simulated results.

Softwaretechnik-Trends•Mar 1, 2002•1 citation

Fourier transform spectrometer studies (300-1000 GHz) of Nb-based quasi-optical SIS detectors

Victor Y. Belitsky, Stellan Jacobsson, Lyudmila V. Filippenko +3 more

Three Nb/AlO/sub x//Nb SIS detectors, designed to operate in the 400-550, 550-700, and 600-750 GHz bands, have been studied in direct detection mode using a Fourier-transform spectrometer. All three detectors were of quasi-optical type and had on-chip-integrated-fixed tuned SIS junctions. The tuning ranges of the detectors were selected to cover the interesting region around the superconducting gap frequency of Nb (about 700 GHz). Measurements show detector responses at frequencies above the gap frequency, i.e., up to /spl ap/920 GHz, and that cooling the detectors to 3.1 K improved the direct detection responses about 15% below 700 GHz and about 50% for frequencies up to 800 GHz, compared to the responses at 4.2 K. The 500 GHz SIS detector was also studied in a 440-520 GHz heterodyne receiver set up. Good agreement between modeled tuning circuit characteristics, tuning range of the mixer and the direct detection response bandwidths were found. However, it is essential that the dispersion of the field penetration depth into the superconductor is included in the modeling of the tuning circuits when the detector is operated at frequencies above the superconducting gap.>

IEEE Transactions on Applied Superconductivity•Jan 1, 1995•8 citations

A 100-GHz fixed-tuned waveguide SIS mixer exhibiting broad bandwidth and very low noise temperature

Sheng-Gai Shi, Takashi Noguchi, Junji Inatani

This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.

IEEE Transactions on Applied Superconductivity•Jan 1, 1997•22 citations

A 650 GHz fixed-tuned waveguide SIS distributed mixer with no integrated tuning circuit

Edward Tong, R. Blundell, Koko G. Megerian +2 more

A Superconductor-Insulator-Superconductor (SIS) distributed mixer with no integrated tuning circuit has been designed for use in a fixed-tuned waveguide mixer block. This mixer employs two half-wave SIS resonators connected in series across the feed point of the waveguide circuit. By selecting appropriate dimensions for the resonators, we can obtain proper impedance matching over a reasonable input bandwidth. Since there is no lossy thin film microstrip line in front of the SIS junction, efficient power transfer from the waveguide feed to the mixer element can be achieved. A receiver noise temperature of 185 K at 650 GHz has been measured with a dual 0.33/spl times/16.8 /spl mu/m SIS resonator. The noise temperature remains below 300 K over an input bandwidth of about 10%. This design can be used at much higher frequency where the loss of tuning circuit becomes significant.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•8 citations
This paper presents the direct-detection responses of a 500-GHz and a 660-GHz waveguide superconducting SIS (superconductor-insulator-superconductor) mixer measured with a Fourier transform spectrometer (FTS). The two superconducting SIS mixers adopt the same type of junction tuning circuit (i.e., parallel connected twin SIS junctions), but are of different designs for the junction feed point where RF signals are coupled and then transmitted to the SIS junction tuning circuit and have different mixer design criteria. The experimental results are discussed in detail.
This paper mainly reports the development of a 0.5-THz waveguide SIS (superconductor – insulator – superconductor) mixer, which adopts twin NbN-based SIS junctions (NbN/AlN/NbN) connected in parallel. The 0.5-THz waveguide NbN SIS mixer is designed incorporating with a 51-μm thick MgO substrate and a waveguide mixer mount with no back-short cavity. Detailed simulation results, junction fabrication process and junction I-V characteristics are described. Preliminary FTS (Fourier Transform Spectrometer) measurement results will also be discussed.
A 600-700GHz SIS mixer with the twin-junction tuning circuit has been designed and fabricated [1] The surface impedance of thin-film superconducting microstrip lines, based on Mattis-Bardeen theory [2], is included in the optimization of RF impedance matching. The receiver noise temperature measured in the frequency range of 630-660GHz is below 200K and the lowest receiver noise temperature of 181K is achieved at 656GHz. The FTS response of the SIS mixer shows a good RF coupling from 600GHz to 700GHz. Both the noise performance and the FTS response can be quantitatively described by numerical results using the quantum theory of mixing. Some detail considerations on the mixer model calculation, such as spreading inductance around the junction tuning structure and mixer's embedding impedance, are discussed. Introduction Nb-based superconductor-insulator-superconductor (SIS) mixers have been used very successfully in sub-mm wavelength detection. Their receiver noise temperature has reached to three times the quantum limit, —3 hfrkB, below the junction's gap frequency. However, at high frequency bands, Nb SIS mixers need to be designed carefully because the photon energy is close to or higher than the gap energy of Nb, A-1.4meV. When the frequency band covers the gap frequency of Nb, —670GHz, the RF loss of Nb superconducting transmission lines increases dramatically and the surface impedance has strong frequency dependence. Usually, the RF properties of a superconducting transmission line can be described by the Mattis-Bardeen theory [2] in good accuracy. From results reported so far [4-9], the best receiver noise temperature is close to 5 hi7kB in the band of 600-700GHz. Despite of the input loss contributed by the experimental setup, some other properties of SIS mixers should be taken into account. In this paper, we characterize the performance of a 600-700GHz mixer by comparing the experimental and simulated results.
Three Nb/AlO/sub x//Nb SIS detectors, designed to operate in the 400-550, 550-700, and 600-750 GHz bands, have been studied in direct detection mode using a Fourier-transform spectrometer. All three detectors were of quasi-optical type and had on-chip-integrated-fixed tuned SIS junctions. The tuning ranges of the detectors were selected to cover the interesting region around the superconducting gap frequency of Nb (about 700 GHz). Measurements show detector responses at frequencies above the gap frequency, i.e., up to /spl ap/920 GHz, and that cooling the detectors to 3.1 K improved the direct detection responses about 15% below 700 GHz and about 50% for frequencies up to 800 GHz, compared to the responses at 4.2 K. The 500 GHz SIS detector was also studied in a 440-520 GHz heterodyne receiver set up. Good agreement between modeled tuning circuit characteristics, tuning range of the mixer and the direct detection response bandwidths were found. However, it is essential that the dispersion of the field penetration depth into the superconductor is included in the modeling of the tuning circuits when the detector is operated at frequencies above the superconducting gap.>
This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.
A Superconductor-Insulator-Superconductor (SIS) distributed mixer with no integrated tuning circuit has been designed for use in a fixed-tuned waveguide mixer block. This mixer employs two half-wave SIS resonators connected in series across the feed point of the waveguide circuit. By selecting appropriate dimensions for the resonators, we can obtain proper impedance matching over a reasonable input bandwidth. Since there is no lossy thin film microstrip line in front of the SIS junction, efficient power transfer from the waveguide feed to the mixer element can be achieved. A receiver noise temperature of 185 K at 650 GHz has been measured with a dual 0.33/spl times/16.8 /spl mu/m SIS resonator. The noise temperature remains below 300 K over an input bandwidth of about 10%. This design can be used at much higher frequency where the loss of tuning circuit becomes significant.