Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Microwave Theory and Techniques

A wideband fixed-tuned SIS receiver for 200-GHz operation

R. Blundell, Edward Tong, D. C. Papa, R. L. Leombruno, Xiaolei Zhang, Scott N. Paine, J. A. Stern, Henry George LeDuc, B. Bumble

Published Apr 1, 1995• 69 citations
Publisher

Abstract

We report on the design and development of a heterodyne receiver, designed to cover the frequency range 176-256 GHz. This receiver incorporates a niobium superconductor-insulator-superconductor (SIS) tunnel junction mixer, which, chiefly for reasons of reliability and ease of operation, is a fixed-tuned waveguide design. On-chip tuning is provided to resonate out the junction's geometric capacitance and produce a good match to the waveguide circuit. Laboratory measurements on the first test receiver indicate that the required input bandwidth (about 40%) is achieved with an average receiver noise temperature of below 50 K. Mixer conversion gain is observed at some frequencies, and the lowest measured receiver noise is less than 30 K. Furthermore, the SIS mixer used in this receiver is of simple construction, is easy to assemble and is therefore a good candidate for duplication.>

DOI
10.1109/22.375257

Related papers

A 100-GHz fixed-tuned waveguide SIS mixer exhibiting broad bandwidth and very low noise temperature

Sheng-Gai Shi, Takashi Noguchi, Junji Inatani

This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.

IEEE Transactions on Applied Superconductivity•Jan 1, 1997•22 citations

A 547 GHz SIS receiver employing a submicron Nb junction with an integrated matching circuit

Pascal Febvre, William R. McGrath, P. D. Batelaan +4 more

A heterodyne receiver using an SIS (superconductor-insulator-superconductor) waveguide mixer with two mechanical tuners has been built and characterized over the frequency range of 460 GHz to 630 GHz. This receiver is designed for radioastronomy applications. The mixer uses high-current-density, 0.25- mu m/sup 2/, Nb/AlO/sub x//Nb SIS tunnel junctions with integrated superconductive RF circuits to tune the junction capacitance. A DSB (double sideband) receiver noise temperature as low as 200+or-17 K has been obtained at 540 GHz. In addition, negative differential resistance has been observed in the DC I-V (current-voltage) curve at 487-491 GHz.>

IEEE MTT-S International Microwave Symposium digest•Dec 30, 2002•4 citations

Development of a waveguide NbN-based SIS mixer in the 900-GHz band

Mahoto Takeda, Yoshinori Uzawa, Zhen Wang +2 more

We have designed and fabricated waveguide superconductor-insulator-superconductor (SIS) receivers at 870 GHz with NbN/AlN/NbN tunnel junctions on an MgO substrate. A waveguide probe was incorporated into the mixer chip for a waveguide-to-microstrip transition. As the tuning circuit for the SIS mixer, we designed a resonant distributed junction whose length is one wavelength and critical current density is 20 kA/cm/sup 2/. The mixing properties were calculated based on the quantum theory of mixing. The SSB mixer noise temperature should be less than 100 K and conversion gain larger than -8.0 dB in the frequency range from 840 to 920 GHz. We also observed the resonance steps of the fabricated SIS mixer. The tuning frequency was slightly higher than the designed frequency.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•6 citations

A 850-GHz waveguide receiver employing a niobium SIS junction fabricated on a 1-μm Si/sub 3/N/sub 4/ membrane

J. Kooi, Jérôme Pety, B. Bumble +4 more

We report on a 850-GHz superconducting-insulator-superconducting (SIS) heterodyne receiver employing an RF-tuned niobium tunnel junction with a current density of 14 kA/cm^2, fabricated on a 1-µm Si_3N_4 supporting membrane. Since the mixer is designed to be operated well above the superconducting gap frequency of niobium (2Δ/h ≈ 690 GHz), special care has been taken to minimize niobium transmission-line losses. Both Fourier transform spectrometer (FTS) measurements of the direct detection performance and calculations of the IF output noise with the mixer operating in heterodyne mode, indicate an absorption loss in the niobium film of about 6.8 dB at 822 GHz. These results are in reasonably good agreement with the loss predicted by the Mattis-Bardeen theory in the extreme anomalous limit. From 800 to 830 GHz, we report uncorrected receiver noise temperatures of 518 or 514 K when we use Callen and Welton's law to calculate the input load temperatures. Over the same frequency range, the mixer has a 4-dB conversion loss and 265 K ± 10 K noise temperature. At 890 GHz, the sensitivity of the receiver has degraded to 900 K, which is primarily the result of increased niobium film loss in the RF matching network. When the mixer was cooled from 4.2 to 1.9 K, the receiver noise temperature improved about 20% 409-K double sideband (DSB). Approximately half of the receiver noise temperature improvement can be attributed to a lower mixer conversion loss, while the remainder is due to a reduction in the niobium film absorption loss. At 982 GHz, we measured a receiver noise temperature of 1916 K.

IEEE Transactions on Microwave Theory and Techniques•Jan 1, 1998•21 citations

Performance of an SIS receiver over 460 GHz to 640 GHz using submicron Nb junctions with integrated RF tuning circuits

Pascal Febvre

The most sensitive heterodyne receivers used formillimeter wave and submillimeter wave radioastronomyemploy superconductor-insulator-superconductor (SIS)tunnel junctions as the nonlinear mixing element. Goodperformance has recently been reported for SIS junctionsused in planar mixer circuits and waveguide mixers fromabout 300 GHz to 500 GHz. We have developed asubmillimeter wave SIS heterodyne receiver for observingimportant rotational transitions of molecules in theinterstellar medium near 550 GHz and 630 GHz. Thisreceiver is based on a waveguide mixer with an adjustablebackshort and E-plane tuner [1]. The mixer uses a highcurrent density, 0.25 gm2 Nb-A1Ox-Nb tunnel junctiondefined by electron beam lithography [2]. The capacitanceof the junction is compensated with an integrated RFsuperconductive microstrip tuning circuit. The receiverperformance has been measured over the frequency range460 GHz to 640 GHz. DSB receiver noise temperatures aslow as 200 ± 17 K at 540 GHz and 362 ± 33 K at626 GHz have been obtained. In addition, negativedifferential resistance has been observed in the DC I-Vcurve at frequencies around 491 GHz. These results indicatethat the superconductive Nb microstrip transmission linesused in the tuning circuits are low-loss and perform well upto at least 90% of the superconductor energy gap frequency.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Aug 30, 1993•0 citations

Fabrication and characterization of a 600-720 GHz resonant distributed SIS junction for fixed-tuned waveguide receiver

T. Matsunaga, Edward Tong, R. Blundell +1 more

The non-linear quasiparticle tunnel current flowing in a distributed superconductor-insulator-superconductor (SIS) transmission line resonator has been exploited in a low-noise heterodyne fixed-tuned waveguide receiver in the 600-720 GHz band. The mixer employs two 1.4 /spl mu/m wide half-wave or full-wave distributed SIS long junctions that are connected in series. These devices have been fabricated with optical lithography. Noise temperatures of 160-240 K have been measured at around 600 GHz. However, the achieved RF bandwidth is only about 5 % and the center frequency of the resonance is also shifted towards lower end of the target frequencies.

Asia-Pacific Microwave Conference (APMC)•Nov 13, 2002•0 citations
We report on the design and development of a heterodyne receiver, designed to cover the frequency range 176-256 GHz. This receiver incorporates a niobium superconductor-insulator-superconductor (SIS) tunnel junction mixer, which, chiefly for reasons of reliability and ease of operation, is a fixed-tuned waveguide design. On-chip tuning is provided to resonate out the junction's geometric capacitance and produce a good match to the waveguide circuit. Laboratory measurements on the first test receiver indicate that the required input bandwidth (about 40%) is achieved with an average receiver noise temperature of below 50 K. Mixer conversion gain is observed at some frequencies, and the lowest measured receiver noise is less than 30 K. Furthermore, the SIS mixer used in this receiver is of simple construction, is easy to assemble and is therefore a good candidate for duplication.>
This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.
A heterodyne receiver using an SIS (superconductor-insulator-superconductor) waveguide mixer with two mechanical tuners has been built and characterized over the frequency range of 460 GHz to 630 GHz. This receiver is designed for radioastronomy applications. The mixer uses high-current-density, 0.25- mu m/sup 2/, Nb/AlO/sub x//Nb SIS tunnel junctions with integrated superconductive RF circuits to tune the junction capacitance. A DSB (double sideband) receiver noise temperature as low as 200+or-17 K has been obtained at 540 GHz. In addition, negative differential resistance has been observed in the DC I-V (current-voltage) curve at 487-491 GHz.>
We have designed and fabricated waveguide superconductor-insulator-superconductor (SIS) receivers at 870 GHz with NbN/AlN/NbN tunnel junctions on an MgO substrate. A waveguide probe was incorporated into the mixer chip for a waveguide-to-microstrip transition. As the tuning circuit for the SIS mixer, we designed a resonant distributed junction whose length is one wavelength and critical current density is 20 kA/cm/sup 2/. The mixing properties were calculated based on the quantum theory of mixing. The SSB mixer noise temperature should be less than 100 K and conversion gain larger than -8.0 dB in the frequency range from 840 to 920 GHz. We also observed the resonance steps of the fabricated SIS mixer. The tuning frequency was slightly higher than the designed frequency.
We report on a 850-GHz superconducting-insulator-superconducting (SIS) heterodyne receiver employing an RF-tuned niobium tunnel junction with a current density of 14 kA/cm^2, fabricated on a 1-µm Si_3N_4 supporting membrane. Since the mixer is designed to be operated well above the superconducting gap frequency of niobium (2Δ/h ≈ 690 GHz), special care has been taken to minimize niobium transmission-line losses. Both Fourier transform spectrometer (FTS) measurements of the direct detection performance and calculations of the IF output noise with the mixer operating in heterodyne mode, indicate an absorption loss in the niobium film of about 6.8 dB at 822 GHz. These results are in reasonably good agreement with the loss predicted by the Mattis-Bardeen theory in the extreme anomalous limit. From 800 to 830 GHz, we report uncorrected receiver noise temperatures of 518 or 514 K when we use Callen and Welton's law to calculate the input load temperatures. Over the same frequency range, the mixer has a 4-dB conversion loss and 265 K ± 10 K noise temperature. At 890 GHz, the sensitivity of the receiver has degraded to 900 K, which is primarily the result of increased niobium film loss in the RF matching network. When the mixer was cooled from 4.2 to 1.9 K, the receiver noise temperature improved about 20% 409-K double sideband (DSB). Approximately half of the receiver noise temperature improvement can be attributed to a lower mixer conversion loss, while the remainder is due to a reduction in the niobium film absorption loss. At 982 GHz, we measured a receiver noise temperature of 1916 K.
The most sensitive heterodyne receivers used formillimeter wave and submillimeter wave radioastronomyemploy superconductor-insulator-superconductor (SIS)tunnel junctions as the nonlinear mixing element. Goodperformance has recently been reported for SIS junctionsused in planar mixer circuits and waveguide mixers fromabout 300 GHz to 500 GHz. We have developed asubmillimeter wave SIS heterodyne receiver for observingimportant rotational transitions of molecules in theinterstellar medium near 550 GHz and 630 GHz. Thisreceiver is based on a waveguide mixer with an adjustablebackshort and E-plane tuner [1]. The mixer uses a highcurrent density, 0.25 gm2 Nb-A1Ox-Nb tunnel junctiondefined by electron beam lithography [2]. The capacitanceof the junction is compensated with an integrated RFsuperconductive microstrip tuning circuit. The receiverperformance has been measured over the frequency range460 GHz to 640 GHz. DSB receiver noise temperatures aslow as 200 ± 17 K at 540 GHz and 362 ± 33 K at626 GHz have been obtained. In addition, negativedifferential resistance has been observed in the DC I-Vcurve at frequencies around 491 GHz. These results indicatethat the superconductive Nb microstrip transmission linesused in the tuning circuits are low-loss and perform well upto at least 90% of the superconductor energy gap frequency.
The non-linear quasiparticle tunnel current flowing in a distributed superconductor-insulator-superconductor (SIS) transmission line resonator has been exploited in a low-noise heterodyne fixed-tuned waveguide receiver in the 600-720 GHz band. The mixer employs two 1.4 /spl mu/m wide half-wave or full-wave distributed SIS long junctions that are connected in series. These devices have been fabricated with optical lithography. Noise temperatures of 160-240 K have been measured at around 600 GHz. However, the achieved RF bandwidth is only about 5 % and the center frequency of the resonance is also shifted towards lower end of the target frequencies.