Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

An Optical Input Module With Superconducting Single-Flux-Quantum Circuit Operating at 1550 nm

Hirotaka Terai, Satoshi Shinada, Kazumasa Makise, Z. Wang, Naoya Wada

Published Feb 11, 2011• 1 citation
Publisher

Abstract

We developed an optical input module consisting of built-in metal-semiconductor-metal photodiodes (MSM-PDs) and co-planar waveguide transmission lines fabricated on an InP substrate, which is flip-chip bonded with a single-flux-quantum (SFQ) circuit fabricated on a Si substrate. To improve photosensitivity of the MSM-PD for a wavelength above 1530 nm at 4 K, we tested the MSM-PDs made of lattice mismatched In1-xGaxAs films on InP substrates. By employing In1-xGaxAs with x=0.44, an apparent reduction of photosensitivity for a wavelength above 1530 nm was suppressed. We also tested newly designed DC/SFQ converters with higher input current sensitivities. The observed current sensitivity was improved to 41 μA, while that in the conventional DC/SFQ converter was 140 μA.

DOI
10.1109/tasc.2010.2103911

Related papers

1550 nm band optical input module with superconducting single-flux-quantum circuit

Satoshi Shinada, Hirotaka Terai, Zhen Wang +1 more

We developed an optical input module with a superconducting single-flux-quantum (SFQ) circuit for application of ultrafast photonic networks in the near future. The optical input module, consisting of a built-in photodiode (PD) with a coplanar waveguide transmission line, was fabricated on an InP substrate and flip-chip bonded with the SFQ circuit on a Si substrate. The fabricated PD showed photosensitivities of more than 0.2 A/W for the wavelength range 1480 to 1530 nm at 4.2 K. SFQ pulses were generated by less than 1 mW optical pulse input.

Applied Physics Letters•May 3, 2010•9 citations

Ultrafast, integrable, optics-based interface between superconducting and room-temperature electronics

Chia-Chi Wang, Marc Currie, T.Y. Hsiang

An ultrafast optical interface between superconducting and room-temperature electronics is proposed to take full advantage of high-speed superconducting circuits. We report on the computed and experimental studies of an optical receiving and modulating system that is compatible in processing with the prevailing integrated-superconducting-circuit technology. Planar interdigitated Nb/Si/Nb metal-semiconductor-metal (MSM) photodiodes are demonstrated as optical receivers with resolvable bit-rate as high as 38 Gb/s, and the response of MSM diode was shaped to be a single-flux-quantum pulse to drive Josephson-junction-based circuits. A similar interdigitated structure on a silicon waveguide is proposed to be an ultrafast light-intensity modulator, with its operation based on carrier-density modulation of the optical index of refraction. This field-effect device has insignificant power dissipation, in addition to high speed. A sample modulator with 5-V bias is shown to have a modulation depth of 40% and a bandwidth over 70 GHz.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•5 citations

Error-Free Operation of Superconducting Nanowire Optical-to-Electrical Converter Connected with SFQ Circuits

Kemmei Kajino, Shigehito Miki, Taro Yamashita +1 more

We report on the demonstration of the error-free operation of optical-to-electrical (O/E) signal converter based on superconducting nanowires with single-flux-quantum circuits. Optical input pulses were generated by the pulse pattern generator and the optical modulator, and the error rate of the output signals was measured. For a 300-nm-wide device with active area of 15×15 μm2, correct O/E conversion was confirmed with the error-rate of less than 10-6at the maximum repetition frequency of 120 MHz. The optical energy consumption per pulse was one order of magnitude lower than those of conventional semiconductor photodiodes.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2015•0 citations

Integration of Optical Waveguides With Single Flux Quantum Circuits

Yoshiki Arita, Nobuyuki Yoshikawa, Baba Toshihiko

Single flux quantum (SFQ) circuits and optical circuits are expected to be used in next-generation integrated circuits. This study investigates basic technologies for integrating optical circuits with SFQ circuits to exploit the advantages of both technologies. We calculated, designed and evaluated metal-clad waveguides, which can be fabricated by the ISTEC standard process (STD2). Light propagates along an 830-μm-long waveguide with a propagation loss of 16 dB/mm. We also designed and evaluated an optical-electrical (O-E) converter that uses a Josephson junction, which can be fabricated by the same process used to fabricate the SFQ circuits. When an optical signal with a peak power of 1.15 mW at 1.548 μm is input, the Josephson O-E converter generates SFQ pulses.

IEEE Transactions on Applied Superconductivity•Jan 7, 2011•1 citation

Optoelectronic clocking system for testing RSFQ circuits up to 20 GHz

J.F. Buzacchelli, Hae-Seung Lee, Sotiris Alexandrou +2 more

Unlike coaxial cable, optical fiber has a bandwidth commensurate with the clock rates of even the fastest rapid single flux quantum (RSFQ) circuits. Employing this advantage, we have developed an optoelectronic clocking system, in which optical pulses from a picosecond laser are delivered via fiber to a superconducting chip, on which metal-semiconductor-metal (MSM) photodiodes generate fast electrical pulses with subpicosecond timing accuracy. An optical pulse splitter, constructed out of beamsplitters, mirrors, and half-wave plates, permits selection of pulse pattern and clock rate from 80.6 MHz up to 20.6 GHz. With a sampling oscilloscope, we have directly observed optical triggering of an RSFQ T flip-flop at frequencies up to 1.3 GHz with a variety of bit patterns. Optical triggering of a Josephson transmission line (JTL) at frequencies up to 20.6 GHz has been verified by precise measurement of the Josephson voltage; this result represents the highest clock rate ever reported for an optical interface for RSFQ circuits.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•22 citations

Sub-Kelvin single flux quantum control circuits and multi-chip packaging for supporting superconducting qubit

Shinichi Yorozu, Toshiyuki Miyazaki, Vasili K. Semenov +6 more

Superconducting single flux quantum (SFQ) circuit can operate at very low temperature. This is suitable for controlling a quantum computing system with Josephson junctions. However, it is difficult to integrate both SFQ circuits and qubits into a single-chip, because of the dissipative characteristics of SFQ circuits. Therefore, we have developed a multi-chip packaging technology for a qubit control module. The module consists of SFQ circuit chips, qubit chips, and a substrate all of which are fabricated with Nb and Al technology. The chips are flip-chip bonded with superconducting solder bumps. We also investigated SFQ control circuits for superconducting qubits and circuit parameter optimization for sub-Kelvin temperature operation. Using both multi-chip packaging and optimized SFQ control circuit makes the design of qubit control module more flexible.

Journal of Physics Conference Series•Jun 1, 2006•3 citations
We developed an optical input module consisting of built-in metal-semiconductor-metal photodiodes (MSM-PDs) and co-planar waveguide transmission lines fabricated on an InP substrate, which is flip-chip bonded with a single-flux-quantum (SFQ) circuit fabricated on a Si substrate. To improve photosensitivity of the MSM-PD for a wavelength above 1530 nm at 4 K, we tested the MSM-PDs made of lattice mismatched In1-xGaxAs films on InP substrates. By employing In1-xGaxAs with x=0.44, an apparent reduction of photosensitivity for a wavelength above 1530 nm was suppressed. We also tested newly designed DC/SFQ converters with higher input current sensitivities. The observed current sensitivity was improved to 41 μA, while that in the conventional DC/SFQ converter was 140 μA.
We developed an optical input module with a superconducting single-flux-quantum (SFQ) circuit for application of ultrafast photonic networks in the near future. The optical input module, consisting of a built-in photodiode (PD) with a coplanar waveguide transmission line, was fabricated on an InP substrate and flip-chip bonded with the SFQ circuit on a Si substrate. The fabricated PD showed photosensitivities of more than 0.2 A/W for the wavelength range 1480 to 1530 nm at 4.2 K. SFQ pulses were generated by less than 1 mW optical pulse input.
An ultrafast optical interface between superconducting and room-temperature electronics is proposed to take full advantage of high-speed superconducting circuits. We report on the computed and experimental studies of an optical receiving and modulating system that is compatible in processing with the prevailing integrated-superconducting-circuit technology. Planar interdigitated Nb/Si/Nb metal-semiconductor-metal (MSM) photodiodes are demonstrated as optical receivers with resolvable bit-rate as high as 38 Gb/s, and the response of MSM diode was shaped to be a single-flux-quantum pulse to drive Josephson-junction-based circuits. A similar interdigitated structure on a silicon waveguide is proposed to be an ultrafast light-intensity modulator, with its operation based on carrier-density modulation of the optical index of refraction. This field-effect device has insignificant power dissipation, in addition to high speed. A sample modulator with 5-V bias is shown to have a modulation depth of 40% and a bandwidth over 70 GHz.>
We report on the demonstration of the error-free operation of optical-to-electrical (O/E) signal converter based on superconducting nanowires with single-flux-quantum circuits. Optical input pulses were generated by the pulse pattern generator and the optical modulator, and the error rate of the output signals was measured. For a 300-nm-wide device with active area of 15×15 μm2, correct O/E conversion was confirmed with the error-rate of less than 10-6at the maximum repetition frequency of 120 MHz. The optical energy consumption per pulse was one order of magnitude lower than those of conventional semiconductor photodiodes.
Single flux quantum (SFQ) circuits and optical circuits are expected to be used in next-generation integrated circuits. This study investigates basic technologies for integrating optical circuits with SFQ circuits to exploit the advantages of both technologies. We calculated, designed and evaluated metal-clad waveguides, which can be fabricated by the ISTEC standard process (STD2). Light propagates along an 830-μm-long waveguide with a propagation loss of 16 dB/mm. We also designed and evaluated an optical-electrical (O-E) converter that uses a Josephson junction, which can be fabricated by the same process used to fabricate the SFQ circuits. When an optical signal with a peak power of 1.15 mW at 1.548 μm is input, the Josephson O-E converter generates SFQ pulses.
Unlike coaxial cable, optical fiber has a bandwidth commensurate with the clock rates of even the fastest rapid single flux quantum (RSFQ) circuits. Employing this advantage, we have developed an optoelectronic clocking system, in which optical pulses from a picosecond laser are delivered via fiber to a superconducting chip, on which metal-semiconductor-metal (MSM) photodiodes generate fast electrical pulses with subpicosecond timing accuracy. An optical pulse splitter, constructed out of beamsplitters, mirrors, and half-wave plates, permits selection of pulse pattern and clock rate from 80.6 MHz up to 20.6 GHz. With a sampling oscilloscope, we have directly observed optical triggering of an RSFQ T flip-flop at frequencies up to 1.3 GHz with a variety of bit patterns. Optical triggering of a Josephson transmission line (JTL) at frequencies up to 20.6 GHz has been verified by precise measurement of the Josephson voltage; this result represents the highest clock rate ever reported for an optical interface for RSFQ circuits.
Superconducting single flux quantum (SFQ) circuit can operate at very low temperature. This is suitable for controlling a quantum computing system with Josephson junctions. However, it is difficult to integrate both SFQ circuits and qubits into a single-chip, because of the dissipative characteristics of SFQ circuits. Therefore, we have developed a multi-chip packaging technology for a qubit control module. The module consists of SFQ circuit chips, qubit chips, and a substrate all of which are fabricated with Nb and Al technology. The chips are flip-chip bonded with superconducting solder bumps. We also investigated SFQ control circuits for superconducting qubits and circuit parameter optimization for sub-Kelvin temperature operation. Using both multi-chip packaging and optimized SFQ control circuit makes the design of qubit control module more flexible.