Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Microwave Theory and Techniques

A Superconducting Tunnel Junction Receiver for 230 GHz

Edmund C. Sutton

Published Jan 1, 1983• 58 citations
Publisher

Abstract

The performance of superconducting tunnel junctions as high-frequency receivers is discussed. Low-noise mixing in superconductor insulator-superconductor (SIS) quasi-particle tunnel junctions has been seen for frequencies up to 400 GHz. Such mixers have the significant advantage of small local-oscillator power requirements. A receiver has been constructed which has a single-sideband (SSB) receiver noise temperature of 305 K at 241 GHz.

DOI
10.1109/tmtt.1983.1131549

Related papers

SIS mixers for low noise millimetre-wave heterodyne receivers

Steven R. Davies, C. T. Cunningham, Leslie T. Little

The development of ultra-low-noise receivers at frequencies of >200 GHz is primarily driven by astronomical applications. The most sensitive millimeter-wave receivers that have presently been constructed make use of the strong mixing afforded by superconductor-insulator-superconductor (SIS) tunnel junctions. In a collaborative project between UKC and RAL, a 230 GHz laboratory receiver has been built using a lead alloy SIS junction as the mixing element, mounted in 4:1 reduced-height waveguide, terminated at one end with a circular cross-section, adjustable backshort. Best results indicate a double-sideband receiver noise temperature of T/sub R/(DSB) approximately=120 K, which represents state-of-the-art performance at this frequency. Initial difficulties in achieving good mixing performance prompted an investigation into the importance of the 'quality' of mixer block backshort tuning elements. An analysis of the mixer equivalent circuit is presented which allows for loss in a non-ideal mixer block, and 3-port mixer model calculations are discussed which incorporate this analysis into the Tucker quantum theory of mixing.

•Mar 22, 1988•0 citations

SIS-Mixer Receiver with Single and Array Tunnel Junctions for the 140 GHZ to 170 GHZ Range

R. Blundell, J. Ibruegger, K. H. Gundlach +1 more

Mixing experiments were made with superconductor-insulator-superconductor (SIS) single tunnel junctions and arrays of junctions. The best receiver noise temperature is 96 K at 150 GHz for a single junction and 67 K at 139.5 GHz for a series array of two junctions. The IF embedding impedance seen by the junction has been measured and its influence on the noise temperature variation over the IF band is shown.

European Microwave Conference (EuMC)•Oct 1, 1984•3 citations

High-frequency limits of superconducting tunnel junction mixers

Dag Winkler, T. Claeson

We have investigated high-frequency limits of superconducting quasiparticle mixers from experiments on Al/Al-oxide-In/Al (or Ag) tunnel junctions, and from calculations based on Tucker’s quantum theory of mixing (QTM). The small superconducting energy gap of Al enabled us to study mixer performance at around the junction gap frequency, fg =(Δ1+Δ2)/h≊87 GHz, of superconductor-insulator-superconductor (SIS) mixers, and at twice the junction gap frequency for S-I-normal metal (SIN) mixers ( fg =Δ1/h) with available millimeter wave sources. Because of the low transition temperature of Al (Tc ≊1.3 K), a dilution refrigerator was used for providing temperatures below 1 K. The best mixer conversion efficiency was obtained for a low-resistance (∼34 Ω) six-junction array SIS mixer operated at f/fg ≊1 (in this case 73 GHz). The coupled single sideband conversion gain (with no image rejection) was −13.8 dB and the available conversion gain was estimated to −8.4 dB. Complicating nonequilibrium phenomena made it difficult to compare the performance of these relatively high-current-density mixers to the QTM. However, good agreement between calculated and corresponding measured conversion efficiencies and dynamic resistance values was obtained for the low-current-density mixers. Noise due to switching between rf-induced Josephson steps and interference from Josephson mixing could be quenched by a magnetic field. Several high-frequency limits are considered in this paper (such as Josephson switching noise, nonequilibrium phenomena, pair breaking, and energy gap limitations). Our results indicate that submillimeter wave SIS mixer receivers are likely to perform well, at least up to their gap frequencies, i.e., the THz region for large gap superconductors. Our QTM calculations showed that conversion gain larger than unity should be possible up to twice the gap frequency. Above this frequency the conversion loss will increase rapidly.

Journal of Applied Physics•Dec 1, 1987•35 citations

Low-noise THz-range Nb based SIS Receivers for Radio Astronomy

Kirill I. Rudakov, Andrey V. Khudchenko, Lyudmila V. Filippenko +4 more

This repost describes our results on development of low-noise heterodyne THz receivers for ground based and space radio astronomy. Superconductor-insulator-superconductor (SIS) mixers that employ high quality Nb-based tunnel junctions are the key element of the most sensitive heterodyne THz receivers. In particular we present here the SIS receivers for frequency range 211-275 GHz and 800-950 GHz with double sideband (DSB) noise temperature of about 25 K and 220 K, respectively. The latest results on development, fabrication techniques and experimental study of the SIS receivers will be discussed.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Nov 8, 2020•7 citations

Low-noise submillimeter-wave NbTiN superconducting tunnel junction mixers

Jonathan H. Kawamura, Jian Chen, David Miller +5 more

We have developed a low-noise 850 GHz superconductor–insulator–superconductor quasiparticle mixer with NbTiN thin-film microstrip tuning circuits and hybrid Nb/AlN/NbTiN tunnel junctions. The mixer uses a quasioptical configuration with a planar twin-slot antenna feeding a two-junction tuning circuit. At 798 GHz, we measured an uncorrected double-sideband receiver noise temperature of TRX=260 K at 4.2 K bath temperature. This mixer outperforms current Nb SIS mixers by a factor of nearly 2 near 800 GHz. The high-gap frequency and low loss at 800 GHz make NbTiN an attractive material with which to fabricate tuning circuits for SIS mixers. NbTiN mixers can potentially operate up to the gap frequency, 2Δ/h∼1.2 THz.

Applied Physics Letters•Dec 20, 1999•81 citations

Dayem-Martin (SIS tunnel junction) mixers for low noise heterodyne receivers

Tom G. Phillips, D. P. Woody, G. J. Dolan +2 more

Superconducting thin film tunnel junctions of small area (.1 \rightarrow 1μm2) have properties which make them suitable for high frequency (≳100 GHz) heterodyne receivers. Both pair and single quasiparticle tunneling is present in these devices, but it is found that the mixing due to the pair effect is apparently excessively noisy, whereas the single quasiparticle effect has a low noise character which gives hope for near quantum limited performance. The physical effect involved is photon assisted quasiparticle tunneling and was first observed by Dayem and Martin[1]. We have made laboratory tests at 115 and 230 GHz which gave single side band (SSB) mixer noise temperatures of 60 and 300 K respectively. Also we have fabricated a 90-140 GHz receiver for the Caltech Owens Valley Radio Observatory which has an overall receiver noise temperature of about 300 K (SSB).

IEEE Transactions on Magnetics•Jan 1, 1981•52 citations
The performance of superconducting tunnel junctions as high-frequency receivers is discussed. Low-noise mixing in superconductor insulator-superconductor (SIS) quasi-particle tunnel junctions has been seen for frequencies up to 400 GHz. Such mixers have the significant advantage of small local-oscillator power requirements. A receiver has been constructed which has a single-sideband (SSB) receiver noise temperature of 305 K at 241 GHz.
The development of ultra-low-noise receivers at frequencies of >200 GHz is primarily driven by astronomical applications. The most sensitive millimeter-wave receivers that have presently been constructed make use of the strong mixing afforded by superconductor-insulator-superconductor (SIS) tunnel junctions. In a collaborative project between UKC and RAL, a 230 GHz laboratory receiver has been built using a lead alloy SIS junction as the mixing element, mounted in 4:1 reduced-height waveguide, terminated at one end with a circular cross-section, adjustable backshort. Best results indicate a double-sideband receiver noise temperature of T/sub R/(DSB) approximately=120 K, which represents state-of-the-art performance at this frequency. Initial difficulties in achieving good mixing performance prompted an investigation into the importance of the 'quality' of mixer block backshort tuning elements. An analysis of the mixer equivalent circuit is presented which allows for loss in a non-ideal mixer block, and 3-port mixer model calculations are discussed which incorporate this analysis into the Tucker quantum theory of mixing.
We have investigated high-frequency limits of superconducting quasiparticle mixers from experiments on Al/Al-oxide-In/Al (or Ag) tunnel junctions, and from calculations based on Tucker’s quantum theory of mixing (QTM). The small superconducting energy gap of Al enabled us to study mixer performance at around the junction gap frequency, fg =(Δ1+Δ2)/h≊87 GHz, of superconductor-insulator-superconductor (SIS) mixers, and at twice the junction gap frequency for S-I-normal metal (SIN) mixers ( fg =Δ1/h) with available millimeter wave sources. Because of the low transition temperature of Al (Tc ≊1.3 K), a dilution refrigerator was used for providing temperatures below 1 K. The best mixer conversion efficiency was obtained for a low-resistance (∼34 Ω) six-junction array SIS mixer operated at f/fg ≊1 (in this case 73 GHz). The coupled single sideband conversion gain (with no image rejection) was −13.8 dB and the available conversion gain was estimated to −8.4 dB. Complicating nonequilibrium phenomena made it difficult to compare the performance of these relatively high-current-density mixers to the QTM. However, good agreement between calculated and corresponding measured conversion efficiencies and dynamic resistance values was obtained for the low-current-density mixers. Noise due to switching between rf-induced Josephson steps and interference from Josephson mixing could be quenched by a magnetic field. Several high-frequency limits are considered in this paper (such as Josephson switching noise, nonequilibrium phenomena, pair breaking, and energy gap limitations). Our results indicate that submillimeter wave SIS mixer receivers are likely to perform well, at least up to their gap frequencies, i.e., the THz region for large gap superconductors. Our QTM calculations showed that conversion gain larger than unity should be possible up to twice the gap frequency. Above this frequency the conversion loss will increase rapidly.
This repost describes our results on development of low-noise heterodyne THz receivers for ground based and space radio astronomy. Superconductor-insulator-superconductor (SIS) mixers that employ high quality Nb-based tunnel junctions are the key element of the most sensitive heterodyne THz receivers. In particular we present here the SIS receivers for frequency range 211-275 GHz and 800-950 GHz with double sideband (DSB) noise temperature of about 25 K and 220 K, respectively. The latest results on development, fabrication techniques and experimental study of the SIS receivers will be discussed.
We have developed a low-noise 850 GHz superconductor–insulator–superconductor quasiparticle mixer with NbTiN thin-film microstrip tuning circuits and hybrid Nb/AlN/NbTiN tunnel junctions. The mixer uses a quasioptical configuration with a planar twin-slot antenna feeding a two-junction tuning circuit. At 798 GHz, we measured an uncorrected double-sideband receiver noise temperature of TRX=260 K at 4.2 K bath temperature. This mixer outperforms current Nb SIS mixers by a factor of nearly 2 near 800 GHz. The high-gap frequency and low loss at 800 GHz make NbTiN an attractive material with which to fabricate tuning circuits for SIS mixers. NbTiN mixers can potentially operate up to the gap frequency, 2Δ/h∼1.2 THz.
Superconducting thin film tunnel junctions of small area (.1 \rightarrow 1μm2) have properties which make them suitable for high frequency (≳100 GHz) heterodyne receivers. Both pair and single quasiparticle tunneling is present in these devices, but it is found that the mixing due to the pair effect is apparently excessively noisy, whereas the single quasiparticle effect has a low noise character which gives hope for near quantum limited performance. The physical effect involved is photon assisted quasiparticle tunneling and was first observed by Dayem and Martin[1]. We have made laboratory tests at 115 and 230 GHz which gave single side band (SSB) mixer noise temperatures of 60 and 300 K respectively. Also we have fabricated a 90-140 GHz receiver for the Caltech Owens Valley Radio Observatory which has an overall receiver noise temperature of about 300 K (SSB).