Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Magnetics

Mixing characteristics of a microwave detector using a granular YBCO superconductor

Yorinobu Yoshisato, Minoru Takai, Kazuya Niki, Shinya Yoshikawa, Toshimasa Hirano, Satoshi Nakano

Published Mar 1, 1991• 6 citations
Publisher

Abstract

Microbridge-type Josephson junctions made of granular bulk YBCO superconductors were experimentally studied at microwave frequencies. Although the bridge included many grain boundaries, clear Shapiro steps were induced at every hf/2e voltage for microwave frequencies, and step height dependence for microwave power similar to that of a single weak link bridge was observed. A heterodyne mixing experiment of microwaves at about 20 GHz was also performed using the detector. The IF signal showed peak amplitudes corresponding to the peak dynamic resistance due to nonlinearity resulting from the Josephson effect. It was confirmed that the detector operates stably for the Josephson-effect heterodyne mixer at 60 K or below. The detector has potential for high sensitivity and good impedance matching due to its large dynamic resistance and high normal state resistance, respectively.

DOI
10.1109/20.133861

Related papers

Heterodyne Detection of Microwaves Using Granular-Type Y1Ba2Cu3O7-x Superconductors

Yorinobu Yoshisato, Akio Takeoka, Minoru Takai +4 more

A heterodyne mixing experiment of microwaves at about 20 GHz was performed using a microwave detector made from granular-type Y1Ba2Cu3O7-x (YBCO) superconductors. Although the bridge included many boundaries, voltage steps corresponding to the Josephson frequency and step height dependence for microwave power similar to those of a single weak-link bridge were clearly observed. The IF signal showed peak amplitudes corresponding to the peak dynamic resistantance due to nonlinearity resulting from the Josephson effect. It was confirmed for the first time that this detector operates stably for the heterodyne mixer at 60 K or below and has a potential for high sensitivity due to its large dynamic resistance.

Japanese Journal of Applied Physics•Apr 1, 1991•10 citations

YBCO microwave grain boundary mixer using a SrTiO/sub 3/ bicrystal substrate

R. Seed, Paul C. Dorsey, Hoton How +2 more

A microwave mixer was patterned on a microstrip transmission line of superconducting YBCO (YBa/sub 2/Cu/sub 3/O/sub 7-x/). The YBCO film was epitaxially laser deposited on a SrTiO/sub 3/ bicrystal substrate. A weak link was constructed by patterning a microbridge in the microstrip at the bicrystal boundary. Microwave signals at 9.000 GHz and 9.941 GHz were applied at the input of the microstrip line. An output intermediate frequency signal was observed at 941 MHz and was detected as the transmitted signal. The microbridge junction, which behaved as a resistively shunted Josephson junction (RSJ), was current biased slightly above the critical current I/sub c/. The mixer conversion loss was measured at the input and output ports of the device package. The mixing efficiency was determined at the device junction. This efficiency was compared with the calculated efficiency determined by numerical solution of the Josephson equation for the weak link junction.>

IEEE Transactions on Magnetics•Nov 1, 1993•4 citations

Experimental Study of Harmonic Mixer Using two HTS YBCO Grain Boundary Josephson Junctions in Series

Mei Yu, H. F. Geng, Tao Hua +6 more

Two high-Tc superconducting (HTS) YBa2Cu3O7-δ(YBCO) grain boundary (GB) Josephson junctions in series as a harmonic mixer is investigated. The research shows that the mixer consisting of two series YBCO Josephson junctions has a larger harmonic number than that with only one junction in heterodyne mixing at zero-voltage bias. One of the advantages of the series-Josephson-junction mixer is that the total critical current is improved without sacrificing the sensitivity of the junctions in the array that makes the mixer easier to get more microwave induced-steps required by larger harmonic number. Furthermore, the underdamped YBCO GB series-Josephson-junction mixer operated at zero-bias voltage, where the zero-order Shapiro step exists, achieves mutual phase locking of the junctions in the array, resulting in an excellent mixing performance. Thus, the series-underdamp-Josephson-junction mixer with zero bias is predominant and compact in terahertz (THz) application due to its excellent performance and no dc bias supply.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Sep 1, 2019•0 citations

Conversion gain and noise of YBa/sub 2/Cu/sub 3/O/sub 7/ weak-link mixers

Donald P. Butler, Jiaqi Wang, Anil Bhandari +1 more

Microwave mixing and parametric conversion in YBa/sub 2/Cu/sub 3/O/sub 7/ microbridges were investigated. The devices have been operated as down-converters, converting a 20-GHz radio frequency to a 1.5-GHz intermediate frequency under the action of an 18.5-GHz local oscillator. The microbridges were fabricated both as granular films on MgO substrates possessing grain boundary weak links and as epitaxial films deposited over substrate steps in LaAlO/sub 3/ substrates. The authors have measured conversion gains as high as -8+or-4 dB when mixing on the nonlinear resistive (superconducting-normal) transition and as high as -30 to -40 dB when parametrically converting via the nonlinear inductance of the bridge at bias currents less than the critical current. Output referred noise powers as low as -206 dB/Hz (3*10/sup -21/ W/Hz) have been measured. In some samples, noise switching events were observed.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•5 citations

Microwave Heterodyne Mixing by Step-Edge Microbridge Josephson Junctions Using YBaCuO Thin Films

Yoshito Fukumoto, Hiroshi Kajikawa, Rikuo Ogawa +1 more

Current-voltage characteristics and microwave mixing properties of step-edge microbridge Josephson junctions (SEJJs) made of YBaCuO thin films were systematically investigated. The step-edge was formed on the surface of a MgO(100) substrate employing the common photolithograph and wet-etching techniques. YBaCuO thin film was deposited by the off-axis sputtering method, and the microbridge junctions were fabricated so as to cross the step-edge. The SEJJs showed typical DC and AC characteristics which were explained by the resistively shunted junction (RSJ) model. Mixing experiments were carried out in the K-band microwave region. An intermediate frequency (IF) output with the frequency range of 20 MHz~2.0 GHz was successfully obtained.

International Conference on Solid State Devices and Materials (SSDM)•Aug 28, 1991•0 citations

Microwave Heterodyne Mixing by Step-Edge Microbridge Josephson Junctions Using YBaCuO Thin Films

Yoshito Fukumoto, Hiroshi Kajikawa, Rikuo Ogawa +1 more

Current-voltage characteristics and microwave mixing properties of step-edge microbridge Josephson junctions (SEJJs) made of YBaCuO thin films were systematically investigated. The step-edge was formed on the surface of a MgO(100) substrate employing the common photolithograph and wet-etching techniques. YBaCuO thin film was deposited by the off-axis sputtering method, and the microbridge junctions were fabricated so as to cross the step-edge. The SEJJs showed typical DC and AC characteristics which were explained by the resistively shunted junction (RSJ) model. Mixing experiments were carried out in the K-band microwave region. An intermediate frequency (IF) output with the frequency range of 20 MHz∼2.0 GHz was successfully obtained.

Japanese Journal of Applied Physics•Dec 1, 1991•17 citations
Microbridge-type Josephson junctions made of granular bulk YBCO superconductors were experimentally studied at microwave frequencies. Although the bridge included many grain boundaries, clear Shapiro steps were induced at every hf/2e voltage for microwave frequencies, and step height dependence for microwave power similar to that of a single weak link bridge was observed. A heterodyne mixing experiment of microwaves at about 20 GHz was also performed using the detector. The IF signal showed peak amplitudes corresponding to the peak dynamic resistance due to nonlinearity resulting from the Josephson effect. It was confirmed that the detector operates stably for the Josephson-effect heterodyne mixer at 60 K or below. The detector has potential for high sensitivity and good impedance matching due to its large dynamic resistance and high normal state resistance, respectively.
A heterodyne mixing experiment of microwaves at about 20 GHz was performed using a microwave detector made from granular-type Y1Ba2Cu3O7-x (YBCO) superconductors. Although the bridge included many boundaries, voltage steps corresponding to the Josephson frequency and step height dependence for microwave power similar to those of a single weak-link bridge were clearly observed. The IF signal showed peak amplitudes corresponding to the peak dynamic resistantance due to nonlinearity resulting from the Josephson effect. It was confirmed for the first time that this detector operates stably for the heterodyne mixer at 60 K or below and has a potential for high sensitivity due to its large dynamic resistance.
A microwave mixer was patterned on a microstrip transmission line of superconducting YBCO (YBa/sub 2/Cu/sub 3/O/sub 7-x/). The YBCO film was epitaxially laser deposited on a SrTiO/sub 3/ bicrystal substrate. A weak link was constructed by patterning a microbridge in the microstrip at the bicrystal boundary. Microwave signals at 9.000 GHz and 9.941 GHz were applied at the input of the microstrip line. An output intermediate frequency signal was observed at 941 MHz and was detected as the transmitted signal. The microbridge junction, which behaved as a resistively shunted Josephson junction (RSJ), was current biased slightly above the critical current I/sub c/. The mixer conversion loss was measured at the input and output ports of the device package. The mixing efficiency was determined at the device junction. This efficiency was compared with the calculated efficiency determined by numerical solution of the Josephson equation for the weak link junction.>
Two high-Tc superconducting (HTS) YBa2Cu3O7-δ(YBCO) grain boundary (GB) Josephson junctions in series as a harmonic mixer is investigated. The research shows that the mixer consisting of two series YBCO Josephson junctions has a larger harmonic number than that with only one junction in heterodyne mixing at zero-voltage bias. One of the advantages of the series-Josephson-junction mixer is that the total critical current is improved without sacrificing the sensitivity of the junctions in the array that makes the mixer easier to get more microwave induced-steps required by larger harmonic number. Furthermore, the underdamped YBCO GB series-Josephson-junction mixer operated at zero-bias voltage, where the zero-order Shapiro step exists, achieves mutual phase locking of the junctions in the array, resulting in an excellent mixing performance. Thus, the series-underdamp-Josephson-junction mixer with zero bias is predominant and compact in terahertz (THz) application due to its excellent performance and no dc bias supply.
Microwave mixing and parametric conversion in YBa/sub 2/Cu/sub 3/O/sub 7/ microbridges were investigated. The devices have been operated as down-converters, converting a 20-GHz radio frequency to a 1.5-GHz intermediate frequency under the action of an 18.5-GHz local oscillator. The microbridges were fabricated both as granular films on MgO substrates possessing grain boundary weak links and as epitaxial films deposited over substrate steps in LaAlO/sub 3/ substrates. The authors have measured conversion gains as high as -8+or-4 dB when mixing on the nonlinear resistive (superconducting-normal) transition and as high as -30 to -40 dB when parametrically converting via the nonlinear inductance of the bridge at bias currents less than the critical current. Output referred noise powers as low as -206 dB/Hz (3*10/sup -21/ W/Hz) have been measured. In some samples, noise switching events were observed.>
Current-voltage characteristics and microwave mixing properties of step-edge microbridge Josephson junctions (SEJJs) made of YBaCuO thin films were systematically investigated. The step-edge was formed on the surface of a MgO(100) substrate employing the common photolithograph and wet-etching techniques. YBaCuO thin film was deposited by the off-axis sputtering method, and the microbridge junctions were fabricated so as to cross the step-edge. The SEJJs showed typical DC and AC characteristics which were explained by the resistively shunted junction (RSJ) model. Mixing experiments were carried out in the K-band microwave region. An intermediate frequency (IF) output with the frequency range of 20 MHz~2.0 GHz was successfully obtained.
Current-voltage characteristics and microwave mixing properties of step-edge microbridge Josephson junctions (SEJJs) made of YBaCuO thin films were systematically investigated. The step-edge was formed on the surface of a MgO(100) substrate employing the common photolithograph and wet-etching techniques. YBaCuO thin film was deposited by the off-axis sputtering method, and the microbridge junctions were fabricated so as to cross the step-edge. The SEJJs showed typical DC and AC characteristics which were explained by the resistively shunted junction (RSJ) model. Mixing experiments were carried out in the K-band microwave region. An intermediate frequency (IF) output with the frequency range of 20 MHz∼2.0 GHz was successfully obtained.