Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Superconducting multiplexer for arrays of transition edge sensors

James A. Chervenak, K. D. Irwin, Erich N. Grossman, John M. Martinis, C. D. Reintsema, M. E. Huber

Published Jun 28, 1999• 286 citations
Publisher

Abstract

We report the design and testing of an analog superconducting time-division multiplexer to instrument large format arrays of low-temperature bolometers and microcalorimeters. The circuit is designed to multiplex an array of superconducting quantum interference devices, thereby simplifying wiring and room temperature electronics. We have fabricated a prototype 8×1 multiplexer chip and show a switching rate of 1 MHz. We calculate that a 32×32 array or larger is feasible.

DOI
10.1063/1.123255

Related papers

A frequency-domain SQUID multiplexer for arrays of transition-edge superconducting sensors

Trevor M. Lanting, Hsiao-Mei Cho, John L. Clarke +5 more

We describe the development of a frequency-domain multiplexer (MUX) to read out arrays of superconducting transition-edge sensors (TES). Fabrication of large-format arrays of these sensors is becoming practical; however, reading out each sensor in the array is a major instrumental challenge. Frequency-domain multiplexing can greatly simplify the instrumentation of large arrays by reducing the number of SQUID's (superconducting quantum interference devices) and wires to the low temperature stages. Each sensor is AC biased at a different frequency, ranging from 380 kHz to 1 MHz. Each sensor signal amplitude-modulates its respective AC bias frequency. An LC filter associated with each sensor suppresses Johnson noise from the other sensors. The signals are combined at a current summing node and measured by a single SQUID. The individual signals from each sensor are then lock-in detected by room temperature electronics. Test chips with fully lithographed LC filters for up to 32 channels have been designed and fabricated. The capacitance and inductance values have been measured and are close to the design goals. We discuss the basic principles of frequency-domain multiplexing, the design and testing of the test chips, and the implementation of a practical system.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•20 citations

Frequency-domain multiplexing for large-scale bolometer arrays

Trevor M. Lanting, Hsiao-Mei Cho, John L. Clarke +5 more

We describe the development of a frequency-domain multiplexer (MUX) to read out arrays of superconducting transition-edge sensors (TES). Fabrication of large-format arrays of these sensors is becoming practical; however, reading out each sensor in the array is a major instrumental challenge that is possibly solved by frequency-domain multiplexing. Each sensor is AC biased at a different frequency, ranging from 380 kHz to 1 MHz. The sensor signal amplitude-modulates its respective AC bias frequency. An LC filter associated with each sensor suppresses Johnson noise from the other sensors. The signals are combined at a current summing node and measured by a single superconducting quantum interference device (SQUID). The individual signals from each sensor are then lock-in detected by room temperature electronics. Test chips with fully lithographed LC filters for up to 32 channels have been designed and fabricated. The capacitance and inductance values have been measured and are close to the design goals. We discuss the basic principles of frequency-domain multiplexing, the design and testing of the test chips, and the implementation of a practical system.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Feb 1, 2003•16 citations

Prototype system for superconducting quantum interference device multiplexing of large-format transition-edge sensor arrays

C. D. Reintsema, J. Beyer, Sae Woo Nam +7 more

We discuss the implementation of a time-division superconducting quantum interference device (SQUID) multiplexing system for the instrumentation of large-format transition-edge sensor arrays. We cover the design and integration of cryogenic SQUID multiplexers and amplifiers, signal management and wiring, analog interface electronics, a digital feedback system, serial-data streaming and management, and system configuration and control. We present data verifying performance of the digital-feedback system. System noise and bandwidth measurements demonstrate the feasibility of adapting this technology for a broad base of applications, including x-ray materials analysis and imaging arrays for future astronomy missions such as Constellation-X (x-ray) and the SCUBA-2 instrument (submillimeter) for the James Clerk Maxwell Telescope.

Review of Scientific Instruments•Sep 25, 2003•100 citations

Time-division superconducting quantum interference device multiplexer for transition-edge sensors

Piet A. J. de Korte, Joern Beyer, Steven W. Deiker +7 more

We report on the design and performance of our second-generation 32-channel time-division multiplexer developed for the readout of large-format arrays of superconducting transition-edge sensors. We present design issues and measurement results on its gain, bandwidth, noise, and cross talk. In particular, we discuss noise performance at low frequency, important for long uninterrupted submillimeter/far-infrared observations, and present a scheme for mitigation of low-frequency noise. Also, results are presented on the decoupling of the input circuit from the first-stage feedback signal by means of a balanced superconducting quantum interference device pair. Finally, the first results of multiplexing several input channels in a switched, digital flux-lock loop are shown.

Review of Scientific Instruments•Jul 23, 2003•177 citations

Code-division multiplexing of superconducting transition-edge sensor arrays

K. D. Irwin, Michael D. Niemack, Joern Beyer +7 more

Multiplexed superconducting quantum interference device (SQUID) amplifiers have recently enabled the deployment of kilopixel arrays of superconducting transition-edge sensor (TES) detectors on a variety of receivers for astrophysics. Existing multiplexing techniques for TES arrays, however, have constraints due to aliasing of SQUID noise, the size of the required filtering elements, or the complexity of the room-temperature electronics that make it difficult to scale to much larger arrays. We have developed a Walsh code-division SQUID multiplexer that has the potential to enable the multiplexing of larger arrays or pixels with faster thermal response times. The multiplexer uses superconducting switches to modulate the polarity of coupling between N individual TES detectors and a single output SQUID channel. The polarities of the detector signals are switched in the pattern of an N × N Walsh matrix, so a frame composed of N orthogonal samples can be used to reconstruct the detector signals without degradation. We present an analysis of the circuit architecture and preliminary results.

Superconductor Science and Technology•Feb 22, 2010•60 citations

SiGe Integrated Circuit∕SQUID Hybrid Cryogenic Multiplexer for Superconducting Bolometer Array

D. Prêle, Fabrice Voisin, R. Oger +6 more

The development of large superconducting bolometer (Transition Edge Sensor: TES) arrays requires ultra low noise amplification and multiplexing electronics. The use of a first transducer stage such as a SQUID (Superconducting QUantum Interference Device) allows ultimate performance in terms of noise. However, the linearization of the SQUID characteristic requires low noise amplification. Furthermore, to realize a time domain multiplexer with SQUIDs, switched biasing is also needed. We have designed an Integrated Circuit (IC) in standard BiCMOS SiGe technology for the readout and the control of a SQUID multiplexer. It includes a low noise amplifier with multiplexed inputs, switched current sources for SQUIDs, and digital circuit for the addressing with only one room temperature clock signal. We have successfully tested this integrated circuit down to 2 K. To validate the operation of a SQUID multiplexer controlled by this SiGe cryogenic IC, we have developed a 2×2 SQUID hybrid demonstrator. It consists of four commercial SQUIDs connected to a SiGe IC.

AIP conference proceedings•Jan 1, 2009•2 citations
We report the design and testing of an analog superconducting time-division multiplexer to instrument large format arrays of low-temperature bolometers and microcalorimeters. The circuit is designed to multiplex an array of superconducting quantum interference devices, thereby simplifying wiring and room temperature electronics. We have fabricated a prototype 8×1 multiplexer chip and show a switching rate of 1 MHz. We calculate that a 32×32 array or larger is feasible.
We describe the development of a frequency-domain multiplexer (MUX) to read out arrays of superconducting transition-edge sensors (TES). Fabrication of large-format arrays of these sensors is becoming practical; however, reading out each sensor in the array is a major instrumental challenge. Frequency-domain multiplexing can greatly simplify the instrumentation of large arrays by reducing the number of SQUID's (superconducting quantum interference devices) and wires to the low temperature stages. Each sensor is AC biased at a different frequency, ranging from 380 kHz to 1 MHz. Each sensor signal amplitude-modulates its respective AC bias frequency. An LC filter associated with each sensor suppresses Johnson noise from the other sensors. The signals are combined at a current summing node and measured by a single SQUID. The individual signals from each sensor are then lock-in detected by room temperature electronics. Test chips with fully lithographed LC filters for up to 32 channels have been designed and fabricated. The capacitance and inductance values have been measured and are close to the design goals. We discuss the basic principles of frequency-domain multiplexing, the design and testing of the test chips, and the implementation of a practical system.
We describe the development of a frequency-domain multiplexer (MUX) to read out arrays of superconducting transition-edge sensors (TES). Fabrication of large-format arrays of these sensors is becoming practical; however, reading out each sensor in the array is a major instrumental challenge that is possibly solved by frequency-domain multiplexing. Each sensor is AC biased at a different frequency, ranging from 380 kHz to 1 MHz. The sensor signal amplitude-modulates its respective AC bias frequency. An LC filter associated with each sensor suppresses Johnson noise from the other sensors. The signals are combined at a current summing node and measured by a single superconducting quantum interference device (SQUID). The individual signals from each sensor are then lock-in detected by room temperature electronics. Test chips with fully lithographed LC filters for up to 32 channels have been designed and fabricated. The capacitance and inductance values have been measured and are close to the design goals. We discuss the basic principles of frequency-domain multiplexing, the design and testing of the test chips, and the implementation of a practical system.
We discuss the implementation of a time-division superconducting quantum interference device (SQUID) multiplexing system for the instrumentation of large-format transition-edge sensor arrays. We cover the design and integration of cryogenic SQUID multiplexers and amplifiers, signal management and wiring, analog interface electronics, a digital feedback system, serial-data streaming and management, and system configuration and control. We present data verifying performance of the digital-feedback system. System noise and bandwidth measurements demonstrate the feasibility of adapting this technology for a broad base of applications, including x-ray materials analysis and imaging arrays for future astronomy missions such as Constellation-X (x-ray) and the SCUBA-2 instrument (submillimeter) for the James Clerk Maxwell Telescope.
We report on the design and performance of our second-generation 32-channel time-division multiplexer developed for the readout of large-format arrays of superconducting transition-edge sensors. We present design issues and measurement results on its gain, bandwidth, noise, and cross talk. In particular, we discuss noise performance at low frequency, important for long uninterrupted submillimeter/far-infrared observations, and present a scheme for mitigation of low-frequency noise. Also, results are presented on the decoupling of the input circuit from the first-stage feedback signal by means of a balanced superconducting quantum interference device pair. Finally, the first results of multiplexing several input channels in a switched, digital flux-lock loop are shown.
Multiplexed superconducting quantum interference device (SQUID) amplifiers have recently enabled the deployment of kilopixel arrays of superconducting transition-edge sensor (TES) detectors on a variety of receivers for astrophysics. Existing multiplexing techniques for TES arrays, however, have constraints due to aliasing of SQUID noise, the size of the required filtering elements, or the complexity of the room-temperature electronics that make it difficult to scale to much larger arrays. We have developed a Walsh code-division SQUID multiplexer that has the potential to enable the multiplexing of larger arrays or pixels with faster thermal response times. The multiplexer uses superconducting switches to modulate the polarity of coupling between N individual TES detectors and a single output SQUID channel. The polarities of the detector signals are switched in the pattern of an N × N Walsh matrix, so a frame composed of N orthogonal samples can be used to reconstruct the detector signals without degradation. We present an analysis of the circuit architecture and preliminary results.
The development of large superconducting bolometer (Transition Edge Sensor: TES) arrays requires ultra low noise amplification and multiplexing electronics. The use of a first transducer stage such as a SQUID (Superconducting QUantum Interference Device) allows ultimate performance in terms of noise. However, the linearization of the SQUID characteristic requires low noise amplification. Furthermore, to realize a time domain multiplexer with SQUIDs, switched biasing is also needed. We have designed an Integrated Circuit (IC) in standard BiCMOS SiGe technology for the readout and the control of a SQUID multiplexer. It includes a low noise amplifier with multiplexed inputs, switched current sources for SQUIDs, and digital circuit for the addressing with only one room temperature clock signal. We have successfully tested this integrated circuit down to 2 K. To validate the operation of a SQUID multiplexer controlled by this SiGe cryogenic IC, we have developed a 2×2 SQUID hybrid demonstrator. It consists of four commercial SQUIDs connected to a SiGe IC.