Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Flattening of cascaded sum- and difference-frequency generation-based wavelength conversion by pump or period detuning

Shiming Gao, Changxi Yang, Xiaosheng Xiao, Yu Tian, Zheng You, Guofan Jin

Published Nov 24, 2005• 0 citations
Publisher

Abstract

We investigate response flatting of cascaded sum- and difference- frequency generation (SFG/DFG)-based wavelength conversion in quasi-phase-matched (QPM) periodically poled lithium niobate waveguides for wavelength division multiplexing optical communication systems. The cascaded SFG/DFG-based configuration shows more robustly combined properties than conventional DFG-based and cascaded second-harmonic generation and DFG (SHG/DFG)-based configurations. The response fluctuation, generated while enhancing the conversion bandwidth, can be efficiently reduced by the method of pump detuning or QPM period detuning.

DOI
10.1117/12.636318

Related papers

All-Optical Wavelength Conversion Based on the Cascaded Sum and Difference Frequency Generation in a Periodically Poled Lithium-Niobate Waveguide

Jian Wang

The principle of all-optical wavelength conversion based on the cascaded sum and difference frequency generation (SFG+DFG) in quasi-phase-matched (QPM) periodically poled LiNbO3 (PPLN) waveguides is introduced. The conversion efficiency of the wavelength converter is calculated. The influences of the powers and span of two pumps on the conversion efficiency are analyzed. Bandwidth of one pump wavelength is discussed. The tuning is about 0.5 nm. The signal pulse width is compressed about 0.68 times.

Optics & Optoelectronic Technology•Jan 1, 2007•0 citations

Ultrabroadband flattop wavelength conversion based on cascaded sum frequency generation and difference frequency generation using pump detuning in quasi-phase-matched lithium niobate waveguides

Meenu Ahlawat, Amirhossein Tehranchi, Chang Qing Xu +1 more

Flattop wavelength conversion over a 70 nm bandwidth in a 45-mm-long periodically poled lithium niobate (PPLN) waveguide based on nonlinear cascaded sum frequency generation (SFG) and difference frequency generation processes using two separated wavelengths, is realized. A 2 dB peak-to-peak ripple over the conversion bandwidth in the C band is observed when the two pumps are fixed for perfectly phase-matched SFG conversion; this is significantly reduced to 0.5 dB by slight detuning of one of the pumps to a longer wavelength. We also demonstrate multichannel broadcasting using two pumps to convert one signal wavelength to three idlers. Using the aperiodically poled lithium niobate waveguide increases the idler separation.

Applied Optics•Aug 5, 2011•11 citations

Comparison of cascaded χ2 wavelength conversions in quasi-phase-matched (QPM) waveguides

Bo Chen, Chang‐Qing Xu

Cascaded second-order nonlinear interaction (&chi(2));based wavelength conversion technique has attracted much attention due to its unique characteristics such as low noise and broadband, which are critical in fiber communication networks. In this report, wavelength conversions based on the newly proposed SFG-DFG (sum frequency generation - difference frequency generation) and conventional SHG-DFG (second harmonic generation - difference frequency generation) are studied and compared both experimentally and theoretically in a LiNbO3 quasi-phase matched (QPM) waveguide. It is shown that the same conversion efficiency can be achieved by employing two pump sources with only half power each (P1, P2) in the SFG-DFG scheme as compared with the SHG-DFG scheme with a single higher power pump beam (P=P1+P2). It is shown that the cascaded SFG-DFG based wavelength conversion has a larger 3-dB pump tolerance bandwidth. The theoretical results are consistent well with the experimental ones. It is found that the pump wavelength difference can be separated by a span as large as 75 nm, while 3-dB signal conversion efficiency is retained in a 45 mm-long device. It is also exhibited that tolerance of temperature for the cascaded SFG-DFG remains the same as that of the cascaded SHG-DFG based devices. The results show that the SFG-DFG wavelength conversion scheme is very attractive for practical applications.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 16, 2004•0 citations

Flattop broadband wavelength converters based on double-pass cascaded SFG + DFG in quasi-phase matched waveguides

Amirhossein Tehranchi, Raman Kashyap

Wavelength converters based on double-pass quasi-phase matched cascaded sum and difference frequency generation in lossy lithium niobate waveguides with a large pump wavelength difference are numerically evaluated assuming pump wavelength detuning to flatten the response.

IEEE Lasers and Electro-Optics Society Annual Meeting (LEOS)•Oct 1, 2009•0 citations

Analysis of picosecond-pulse wavelength conversion based on cascaded sum-frequency generation and difference-frequency generation in quasi-phase-matched LiNbO3 waveguides

Yong Wang, Chang-Qing Xu

Wavelength conversion based on the cascaded sum-frequency generation and difference-frequency generation (cSFG+DFG) process in quasi-phase-matched (QPM) periodically poled lithium niobate (PPLN) waveguides has the advantage of no pump occupation in the communication band, compared to the traditional cascaded second-harmonic generation (SHG) and DFG process. In cSFG+DFG-based wavelength conversion, two pump waves and a signal wave are required. The input pulse train, as a carrier of information, can be applied to either the signal or one of the two pump waves. Though the converted wave is in the form of pulses, its temporal and spectral characteristics are dependent on the arrangement of the pulsed wave. In this work, we target the wavelength conversion of 40-GHz picosecond pulse trains, and systematically analyze the temporal and spectral characteristics of the pump, signal, converted, and sum-frequency waves during their propagations in PPLN waveguides by using numerical simulation. In particular, pulse shapes, optical spectra, phases and conversion efficiency are compared when the picosecond pulse train is used as the signal and pump waves, respectively.

Optical Engineering•May 1, 2007•4 citations

Broadband wavelength converter based on segmented quasi-phase matched grating

Tao Liu, Baogang Li

Broadband wavelength converters based on difference frequency generation (DFG), single-pass and double-pass cascaded second harmonic generation and difference frequency generation (SHG+DFG), single-pass and double-pass cascaded sum and difference frequency generation (SFG+DFG) are fulfilled by utilizing segmented grating structure in lithium niobate waveguide. Under the small-signal approximation, the effects of the waveguide length and the response flatness on DFG-based wavelength conversion are investigated by use of matrix operator, and then a feasible scheme to enhance the bandwidth and stability of signal and pump wave is proposed. For single-pass/double-pass SHG+DFG wavelength conversion scheme and single-pass/double-pass SFG+DFG wavelength conversion scheme, the effect of segmented grating structure on conversion bandwidth is studied theoretically and numerically, the results show that the signal conversion bandwidth can be broadened by optimizing the aperiodic grating. Moreover, the influence of "balance condition" on double-pass SFG+DFG-based wavelength conversion is analyzed, one can achieve enhanced conversion efficiency and conversion bandwidth by adjusting the power and wavelengths of pump sources according to the "balance condition". In the end, a reasonable suggestion is presented to achieve broadband wavelength conversion under different requirements.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Aug 24, 2010•1 citation
We investigate response flatting of cascaded sum- and difference- frequency generation (SFG/DFG)-based wavelength conversion in quasi-phase-matched (QPM) periodically poled lithium niobate waveguides for wavelength division multiplexing optical communication systems. The cascaded SFG/DFG-based configuration shows more robustly combined properties than conventional DFG-based and cascaded second-harmonic generation and DFG (SHG/DFG)-based configurations. The response fluctuation, generated while enhancing the conversion bandwidth, can be efficiently reduced by the method of pump detuning or QPM period detuning.
The principle of all-optical wavelength conversion based on the cascaded sum and difference frequency generation (SFG+DFG) in quasi-phase-matched (QPM) periodically poled LiNbO3 (PPLN) waveguides is introduced. The conversion efficiency of the wavelength converter is calculated. The influences of the powers and span of two pumps on the conversion efficiency are analyzed. Bandwidth of one pump wavelength is discussed. The tuning is about 0.5 nm. The signal pulse width is compressed about 0.68 times.
Flattop wavelength conversion over a 70 nm bandwidth in a 45-mm-long periodically poled lithium niobate (PPLN) waveguide based on nonlinear cascaded sum frequency generation (SFG) and difference frequency generation processes using two separated wavelengths, is realized. A 2 dB peak-to-peak ripple over the conversion bandwidth in the C band is observed when the two pumps are fixed for perfectly phase-matched SFG conversion; this is significantly reduced to 0.5 dB by slight detuning of one of the pumps to a longer wavelength. We also demonstrate multichannel broadcasting using two pumps to convert one signal wavelength to three idlers. Using the aperiodically poled lithium niobate waveguide increases the idler separation.
Cascaded second-order nonlinear interaction (&chi(2));based wavelength conversion technique has attracted much attention due to its unique characteristics such as low noise and broadband, which are critical in fiber communication networks. In this report, wavelength conversions based on the newly proposed SFG-DFG (sum frequency generation - difference frequency generation) and conventional SHG-DFG (second harmonic generation - difference frequency generation) are studied and compared both experimentally and theoretically in a LiNbO3 quasi-phase matched (QPM) waveguide. It is shown that the same conversion efficiency can be achieved by employing two pump sources with only half power each (P1, P2) in the SFG-DFG scheme as compared with the SHG-DFG scheme with a single higher power pump beam (P=P1+P2). It is shown that the cascaded SFG-DFG based wavelength conversion has a larger 3-dB pump tolerance bandwidth. The theoretical results are consistent well with the experimental ones. It is found that the pump wavelength difference can be separated by a span as large as 75 nm, while 3-dB signal conversion efficiency is retained in a 45 mm-long device. It is also exhibited that tolerance of temperature for the cascaded SFG-DFG remains the same as that of the cascaded SHG-DFG based devices. The results show that the SFG-DFG wavelength conversion scheme is very attractive for practical applications.
Wavelength conversion based on the cascaded sum-frequency generation and difference-frequency generation (cSFG+DFG) process in quasi-phase-matched (QPM) periodically poled lithium niobate (PPLN) waveguides has the advantage of no pump occupation in the communication band, compared to the traditional cascaded second-harmonic generation (SHG) and DFG process. In cSFG+DFG-based wavelength conversion, two pump waves and a signal wave are required. The input pulse train, as a carrier of information, can be applied to either the signal or one of the two pump waves. Though the converted wave is in the form of pulses, its temporal and spectral characteristics are dependent on the arrangement of the pulsed wave. In this work, we target the wavelength conversion of 40-GHz picosecond pulse trains, and systematically analyze the temporal and spectral characteristics of the pump, signal, converted, and sum-frequency waves during their propagations in PPLN waveguides by using numerical simulation. In particular, pulse shapes, optical spectra, phases and conversion efficiency are compared when the picosecond pulse train is used as the signal and pump waves, respectively.
Broadband wavelength converters based on difference frequency generation (DFG), single-pass and double-pass cascaded second harmonic generation and difference frequency generation (SHG+DFG), single-pass and double-pass cascaded sum and difference frequency generation (SFG+DFG) are fulfilled by utilizing segmented grating structure in lithium niobate waveguide. Under the small-signal approximation, the effects of the waveguide length and the response flatness on DFG-based wavelength conversion are investigated by use of matrix operator, and then a feasible scheme to enhance the bandwidth and stability of signal and pump wave is proposed. For single-pass/double-pass SHG+DFG wavelength conversion scheme and single-pass/double-pass SFG+DFG wavelength conversion scheme, the effect of segmented grating structure on conversion bandwidth is studied theoretically and numerically, the results show that the signal conversion bandwidth can be broadened by optimizing the aperiodic grating. Moreover, the influence of "balance condition" on double-pass SFG+DFG-based wavelength conversion is analyzed, one can achieve enhanced conversion efficiency and conversion bandwidth by adjusting the power and wavelengths of pump sources according to the "balance condition". In the end, a reasonable suggestion is presented to achieve broadband wavelength conversion under different requirements.