Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Pure and Applied Optics Journal of the European Optical Society Part A

Three- and four-wave forward amplification in AC fields

Yu. V. Miklyaev, V. I. Safonov

Published Mar 1, 1997• 0 citations
Publisher

Abstract

Forward three- and four-wave mixing in a photorefractive crystal are studied theoretically for the case of an AC field applied to the crystal and illuminated by a standing or moving interference pattern. The gain coefficients are obtained in the undepleted pump approximation. A comparison is made of the forward wave gain for the different mechanisms of signal beam amplification.

DOI
10.1088/0963-9659/6/2/009

Related papers

New gain mechanism for wave amplification in photorefractive materials

Klaus H. Ringhofer, LASZLO SOLYMAR

It is shown that there is a gain mechanism in three- and four-wave forward interactions in which power is transferred inwards from the pump beams to the signal beams. The special case of amplifying a wave halfway between the pump waves is discussed.

Applied Physics Letters•Sep 19, 1988•53 citations

Photorefractive four-wave mixing with high-speed modulated beams

Yan Li, Xiudong Sun, Yongyuan Jiang +2 more

Photorefractive four-wave mixing with high-speed modulated beams is studied theoretically. The analytical solutions for the steady-state coupled equations describing four-wave mixing with an arbitrary complex-coupling constant are given without the undepleted-pump approximation.

Journal of the Optical Society of America B•Dec 1, 1997•3 citations

Noise-free Photorefractive Image Amplifiers

Henri J. Rajbenbach, A. Delboulbé, Jean‐Pierre Huignard

When a weak optical signal is injected in a photorefractive crystal illuminated with a strong pump beam, it experiences gain via a two-wave mixing process.(1) A problem common to these amplifiers is the presence of noise sources that corrupt the quality of the emerging amplified optical signal. We propose and experimentally demonstrate the first technique, to our knowledge, capable of very significantly reducing the optical noise while maintaining high gain coefficients. Consider two-wave mixing in a slowly rotating crystal. First, we estimate the influence of a crystal rotation (angular velocity Ω around the point O) on the noise intensity in the output plane (Fig. 1a). A noise source located around point A radiates a complex wavefront whose component along the direction of the injected signal is represented by a plane wave of intensity IN (A is a crystal imperfection or interface). It is essential to note that the noise sources are bounded to the crystal and will consequently move with it. This is the basis for the process of discrimination between the noise gratings and the injected signal grating. In the Ox coordinate bounded to the rotating crystal, the interference pattern responsible for the formation of a noise grating around the point A is given by: IN(x,t) = I0 [1 + mN cos KN(t)x], where KN(t) ~ 2π(θ + Ωt)/λ is the time-dependent grating wave vector (we have assumed that the angles inside the crystal are small), I0 is the total incident intensity (I0 ~ IP0), θ is the angle between the beams inside the crystal, λ = λ0/n is the optical wavelength in the crystal with refractive index n, and mN is the fringe modulation.

Photorefractive Effects, Materials, and Devices•Jan 1, 1990•0 citations

Four-wave mixing in photorefractive crystals with depleted pumps: an analytical treatment

J. Goltz, Theo T. Tschudi

We present an analytical approximative solution of four-wave mixing in photorefractive crystals with depleted pumps for the case of a negative coupling coefficient and then discuss the solution.

Optics Letters•Apr 15, 1989•3 citations

Pulsed amplification of continuous-wave signal fields in photorefractive BaTiO3

Nikolaos A. Vainos, S. Mailis, M. C. Gower

High-gain pulsed amplification of low intensity continuous-wave optical signals via two-wave mixing in a photorefractive barium titanate (BaTiO3) crystal is demonstrated. The technique relies on the nonlinear mixing between a signal field and a pump field produced via pulsed amplification of a continuous-wave field in excimer-pumped dye amplifiers.

Applied Physics Letters•Mar 30, 1992•2 citations

Photorefractive wave mixing with finite beams

Wieslaw Z. Krolikowski, Mark Cronin‐Golomb

While the interaction of optical beams in photorefractive crystals can often be accurately described in terms of 1-D plane-wave approximation, 2-D models are sometimes more suitable, as suggested by recent work.1 Here we discuss some aspects of photorefractive interaction of finite size optical beams. We have solved the system of partial differential equations governing two- and four-wave mixing numerically by using iterative procedures. Simulations of beam amplification in two-beam coupling show strong beam deformation even without any spatial information imposed on them. Spatially nonuniform energy transfer is responsible for this effect. The pump beam loses energy during propagation and at the end of its passage through the beam intersection region (which was completely inside the crystal) it is strongly depleted and cannot contribute significantly to beam amplification. As the pump beam crosses through the probe, it amplifies most strongly that side of the probe that it meets first. By the time the pump has reached the far side of the probe, it is strongly depleted and less effective at probe amplification. In the case of phase conjugation through four-wave mixing, we found that the conjugate beam is strongly deformed only when the coupling constant is negative (corresponding to deamplification of the probe input beam). For positive coupling constants the output conjugate beam is a good replica of the input probe beam.

Annual Meeting Optical Society of America•Jan 1, 1991•1 citation
Forward three- and four-wave mixing in a photorefractive crystal are studied theoretically for the case of an AC field applied to the crystal and illuminated by a standing or moving interference pattern. The gain coefficients are obtained in the undepleted pump approximation. A comparison is made of the forward wave gain for the different mechanisms of signal beam amplification.
When a weak optical signal is injected in a photorefractive crystal illuminated with a strong pump beam, it experiences gain via a two-wave mixing process.(1) A problem common to these amplifiers is the presence of noise sources that corrupt the quality of the emerging amplified optical signal. We propose and experimentally demonstrate the first technique, to our knowledge, capable of very significantly reducing the optical noise while maintaining high gain coefficients. Consider two-wave mixing in a slowly rotating crystal. First, we estimate the influence of a crystal rotation (angular velocity Ω around the point O) on the noise intensity in the output plane (Fig. 1a). A noise source located around point A radiates a complex wavefront whose component along the direction of the injected signal is represented by a plane wave of intensity IN (A is a crystal imperfection or interface). It is essential to note that the noise sources are bounded to the crystal and will consequently move with it. This is the basis for the process of discrimination between the noise gratings and the injected signal grating. In the Ox coordinate bounded to the rotating crystal, the interference pattern responsible for the formation of a noise grating around the point A is given by: IN(x,t) = I0 [1 + mN cos KN(t)x], where KN(t) ~ 2π(θ + Ωt)/λ is the time-dependent grating wave vector (we have assumed that the angles inside the crystal are small), I0 is the total incident intensity (I0 ~ IP0), θ is the angle between the beams inside the crystal, λ = λ0/n is the optical wavelength in the crystal with refractive index n, and mN is the fringe modulation.
While the interaction of optical beams in photorefractive crystals can often be accurately described in terms of 1-D plane-wave approximation, 2-D models are sometimes more suitable, as suggested by recent work.1 Here we discuss some aspects of photorefractive interaction of finite size optical beams. We have solved the system of partial differential equations governing two- and four-wave mixing numerically by using iterative procedures. Simulations of beam amplification in two-beam coupling show strong beam deformation even without any spatial information imposed on them. Spatially nonuniform energy transfer is responsible for this effect. The pump beam loses energy during propagation and at the end of its passage through the beam intersection region (which was completely inside the crystal) it is strongly depleted and cannot contribute significantly to beam amplification. As the pump beam crosses through the probe, it amplifies most strongly that side of the probe that it meets first. By the time the pump has reached the far side of the probe, it is strongly depleted and less effective at probe amplification. In the case of phase conjugation through four-wave mixing, we found that the conjugate beam is strongly deformed only when the coupling constant is negative (corresponding to deamplification of the probe input beam). For positive coupling constants the output conjugate beam is a good replica of the input probe beam.