Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physica C Superconductivity

Fabrication of low noise high-Tc bicrystal junction rf SQUID

Fei Xie, J.C. Wang, Dongfeng He, Ruijuan Nie, Tao Yang, P. Ma, L.Y. Liu, Yuan Dai, S.G. Wang, S.Z. Wang

Published Nov 1, 2000• 0 citations
Publisher
DOI
10.1016/s0921-4534(00)01485-4

Related papers

YBCO thin film rf-SQUID using bicrystal junction

Neeraj Khare

Physica C Superconductivity•Feb 1, 1999•2 citations

MM wave Josephson generation in High-Tc bicrystal junction arrays

K. Y. Constantinian, A.D. Mashtakov, G. A. Ovsyannikov +5 more

•Jan 1, 1999•0 citations

Resonant frequency of high Tc rf-SQUID resonator

Akira Sakai

The Japan Society of Applied Physics•Jul 4, 2013•0 citations

Design and fabrication of the High-tc radiofrequencyamplifier with the microstrip input coil based on bicrystal dc SQUID

Michael A. Tarasov, Oleg V. Snigirev, Alexei Kalabukhov +2 more

•Jan 1, 2000•1 citation

High Performance DC Superconducting Quantum Interference Device Utilizing a Bicrystal Junction with a 30° Misorientation Angle

Tadashi Minotani, Satoru Kawakami, Takanobu KISS +2 more

A high T c dc superconducting quantum interference device (SQUID) was fabricated using a bicrystal junction with a misorientation angle of θ=30°. The junction with a width of 2 µ m exhibited high resistance R s=10 Ω and critical current I 0=25 µ A at T=77 K. This gives a I 0 R s as high as 250 µ V. These values indicate that the bicrystal junction has great potential for the development of high performance SQUIDs. The SQUID fabricated with a 30° junction exhibited voltage modulation depths as high as ΔV=85 µ V, 40 µ V and 20 µ V at T=77 K for the inductance values of L s=60 pH, 100 pH and 160 pH, respectively. These are the highest values reported so far. Preliminary noise measurement showed that the flux noise of the SQUID is less than 8 µΦ0/ Hz1/2 for the white noise region, and less than 70 µΦ0/ Hz1/2 at f=1 Hz when the 60 pH-SQUID is dc biased and operated with a conventional Flux Locked Loop (FLL) circuit.

Japanese Journal of Applied Physics•Aug 1, 1997•30 citations

Fabrication and Evaluation of RF SQUID on Bicrystalline Substrates

Guan Tianfang, Shimonaka Masayuki, Kong Xiang-Yan +3 more

IEICE Technical Report; IEICE Tech. Rep.•Jan 13, 2010•0 citations
A high T c dc superconducting quantum interference device (SQUID) was fabricated using a bicrystal junction with a misorientation angle of θ=30°. The junction with a width of 2 µ m exhibited high resistance R s=10 Ω and critical current I 0=25 µ A at T=77 K. This gives a I 0 R s as high as 250 µ V. These values indicate that the bicrystal junction has great potential for the development of high performance SQUIDs. The SQUID fabricated with a 30° junction exhibited voltage modulation depths as high as ΔV=85 µ V, 40 µ V and 20 µ V at T=77 K for the inductance values of L s=60 pH, 100 pH and 160 pH, respectively. These are the highest values reported so far. Preliminary noise measurement showed that the flux noise of the SQUID is less than 8 µΦ0/ Hz1/2 for the white noise region, and less than 70 µΦ0/ Hz1/2 at f=1 Hz when the 60 pH-SQUID is dc biased and operated with a conventional Flux Locked Loop (FLL) circuit.