Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Behavior of edge-grown low-capacitance superconducting tunnel junctions

G. Dousselin, Jorge Rosenblatt

Published Jan 1, 1980• 7 citations
Publisher

Abstract

By growing the oxide barrier on the edge of a thin film rather than on its flat surface, we have succeeded in obtaining small-area tunnel junctions. The fabrication process suitable for integration of many elements in small circuits is described. Supercurrent response to magnetic and microwave fields unambiguously characterize the Josephson behavior of these junctions.

DOI
10.1063/1.327298

Related papers

Fabrication of ultrasmall Nb-AlOx-Nb Josephson tunnel junctions

John M. Martinis, Ronald H. Ono

We describe a fabrication process to make Nb-AlOx-Nb edge junctions with areas as small as 0.0022 μm2 and with current densities from 10 to 24 000 A/cm2. The junction conductance was low for voltages below the superconducting energy gap which indicates good quality tunnel barriers. Coulomb gap measurements obtained when the junctions were in the normal state were used to find the junction capacitance. Junction capacitance as small as 0.18 fF has been measured.

Applied Physics Letters•Aug 6, 1990•34 citations

Fabrication and dc characteristics of small-area tantalum and niobium superconducting tunnel junctions

Dean W. Face, D. E. Prober

We discuss the fabrication and dc electrical characteristics of small-area (1–6 μm2) superconducting tunnel junctions with Ta or Nb base electrodes and Pb or Pb0.9Bi0.1 counterelectrodes. These junctions have very small subgap leakage currents, a ‘‘sharp’’ current rise at the sum-gap voltage, and show strong quantum effects when used as microwave mixers. The use of a low-energy (∼150 eV) ion cleaning process and a novel step-defined fabrication process that eliminates photoresist processing after base electrode deposition are discussed. Tunnel barriers formed by dc glow discharge oxidation were the most successful. Tunnel barrier formation by thermal oxidation and ion-beam oxidation is also discussed. An oxidized Ta overlayer (∼7 nm thick) was found to improve the characteristics of Nb-based junctions. The electrical characteristics of junctions with different electrode and barrier materials are presented and discussed in terms of the physical mechanisms that lead to excess subgap current and to a width of the current rise at the sum-gap voltage.

Journal of Applied Physics•Oct 15, 1987•13 citations

Nb/Nb oxide/Pb-alloy Josephson tunnel junctions

Stanley I. Raider, R.E. Drake

A procedure is described for fabricating thin film Nb/Nb oxide/Pb-alloy Josephson tunnel junctions that satisfies the principal requirements for integrated circuit design and fabrication. A deposited Nb film, evaporated from an e-gun heated source, was patterned by chemical etching to form a base electrode. A junction was completed by plasma etching and plasma oxidizing the Nb junction area to form a tunnel barrier and by depositing a Pb alloy counterelectrode. Josephson tunnel junctions with Nb/Nb oxide/Pb-Au-In structures were prepared with low excess subgap currents in the current-voltage (I-V) curve and with reproducible and stable I-V characteristics. Variations in junction current density from run-run were ± 15%. Seven 3-junction interferomeeters out of a population of 50,000 were shorted (99.99% yield) for causes not immediately attributable to photoresist-related defects. No changes in Josephson current were detected after thermal cycling 17,000 interferometers 1,800 × between room temperature and 4.2°K, after storing them for 2 years at 5°C, or after annealing 5,000 interferometers for 4.5 hours at 70°C.

IEEE Transactions on Magnetics•Jan 1, 1981•41 citations

SUPERCONDUCTING QUANTUM CIRCUITS

Johannes Majer

This thesis describes a number of experiments with superconducting cir- cuits containing small Josephson junctions. The circuits are made out of aluminum islands which are interconnected with a very thin insulating alu- minum oxide layer. The connections form a Josephson junction. The current trough the junction is related to the superconducting phase difference across the junction and described by the well-known Josephson relation. The char- acteristic energy scale for this effect is the Josephson energy, which is a measure for the strength of the coupling of the islands. Due to the parallel plate geometry of the junction a capacitance is formed. This capacitance leads to a charging effect. The characteristic energy scale for this effect is given by the charging energy. With the shadow evaporation technique it is possible to make the Josephson junction area very small and the two characteristic energy scales of the same order of magnitude. Charge and phase are conju- gate variables. Therefore a circuit containing such small Josephson junctions exhibits quantum effects. The microfabrication technique used in this the- sis allows fabrication of solid circuits with controlled quantum mechanical behavior.

WORLD SCIENTIFIC eBooks•Jul 21, 2019•25 citations

Superconducting tunnel junction structures designed for qubit realizations

Detlef Born, Th. Wagner, Wolfram Krech +2 more

In view of future macroscopic quantum experiments, we have fabricated prototypes of charge qubits (with tunable Josephson coupling and capacitive gate) provided with capacitively coupled readout single-electron transistor electrometers. The devices are prepared by electron beam direct-writing in conjunction with material deposition by sputtering. All leads are made of Al, and the AlO/sub x/ tunnel barriers are generated by local thermal oxidizing of the surface of the base striplines. The island electrodes are made of Al or Nb in a subsequent deposition step. In the case of Nb it is suitable to protect the barriers by a thin sputtered Al film first. The small-area (100 nm/spl times/100 nm) tunnel junctions have capacitances in the order of a few 10/sup -16/ F; their resistances can be adjusted in a wide range from k/spl Omega/ to M/spl Omega/ with an on-chip spread of less than 10%. The (double) superconducting gap energy was determined to be about 0.4 meV for Al and 1.4 meV for Nb, respectively. Measuring the so-called Coulomb staircase, we have demonstrated the operation of both qubit boxes and sub-e electrometers.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•1 citation

Fabrication of experimental Josephson tunneling circuits

J. H. Greiner, S. Basavaiah, I. Ames

A multilevel thin-film process has been developed for fabricating experimental circuits containing Josephson tunneling gates, insulated crossings, superconducting contacts, and terminating resistors. The process utilizes a Nb film for the ground plane and Pb alloy films for overlying superconducting layers. Insulation is achieved through the use of vacuum-deposited SiO films and anodization of the Nb ground plane. An oxide formed by rf sputter-etching in an oxygen plasma is used for forming the tunneling barriers. Photoprocessing techniques are used for patterning. Through use of the process it has been possible to fabricate experimental memory and logic circuits which survive thermal cycling to 4.2 K and intervening storage at room temperature without significant changes in electrical characteristics.

Journal of Vacuum Science and Technology•Jan 1, 1974•67 citations
By growing the oxide barrier on the edge of a thin film rather than on its flat surface, we have succeeded in obtaining small-area tunnel junctions. The fabrication process suitable for integration of many elements in small circuits is described. Supercurrent response to magnetic and microwave fields unambiguously characterize the Josephson behavior of these junctions.
We discuss the fabrication and dc electrical characteristics of small-area (1–6 μm2) superconducting tunnel junctions with Ta or Nb base electrodes and Pb or Pb0.9Bi0.1 counterelectrodes. These junctions have very small subgap leakage currents, a ‘‘sharp’’ current rise at the sum-gap voltage, and show strong quantum effects when used as microwave mixers. The use of a low-energy (∼150 eV) ion cleaning process and a novel step-defined fabrication process that eliminates photoresist processing after base electrode deposition are discussed. Tunnel barriers formed by dc glow discharge oxidation were the most successful. Tunnel barrier formation by thermal oxidation and ion-beam oxidation is also discussed. An oxidized Ta overlayer (∼7 nm thick) was found to improve the characteristics of Nb-based junctions. The electrical characteristics of junctions with different electrode and barrier materials are presented and discussed in terms of the physical mechanisms that lead to excess subgap current and to a width of the current rise at the sum-gap voltage.
A procedure is described for fabricating thin film Nb/Nb oxide/Pb-alloy Josephson tunnel junctions that satisfies the principal requirements for integrated circuit design and fabrication. A deposited Nb film, evaporated from an e-gun heated source, was patterned by chemical etching to form a base electrode. A junction was completed by plasma etching and plasma oxidizing the Nb junction area to form a tunnel barrier and by depositing a Pb alloy counterelectrode. Josephson tunnel junctions with Nb/Nb oxide/Pb-Au-In structures were prepared with low excess subgap currents in the current-voltage (I-V) curve and with reproducible and stable I-V characteristics. Variations in junction current density from run-run were ± 15%. Seven 3-junction interferomeeters out of a population of 50,000 were shorted (99.99% yield) for causes not immediately attributable to photoresist-related defects. No changes in Josephson current were detected after thermal cycling 17,000 interferometers 1,800 × between room temperature and 4.2°K, after storing them for 2 years at 5°C, or after annealing 5,000 interferometers for 4.5 hours at 70°C.
This thesis describes a number of experiments with superconducting cir- cuits containing small Josephson junctions. The circuits are made out of aluminum islands which are interconnected with a very thin insulating alu- minum oxide layer. The connections form a Josephson junction. The current trough the junction is related to the superconducting phase difference across the junction and described by the well-known Josephson relation. The char- acteristic energy scale for this effect is the Josephson energy, which is a measure for the strength of the coupling of the islands. Due to the parallel plate geometry of the junction a capacitance is formed. This capacitance leads to a charging effect. The characteristic energy scale for this effect is given by the charging energy. With the shadow evaporation technique it is possible to make the Josephson junction area very small and the two characteristic energy scales of the same order of magnitude. Charge and phase are conju- gate variables. Therefore a circuit containing such small Josephson junctions exhibits quantum effects. The microfabrication technique used in this the- sis allows fabrication of solid circuits with controlled quantum mechanical behavior.
In view of future macroscopic quantum experiments, we have fabricated prototypes of charge qubits (with tunable Josephson coupling and capacitive gate) provided with capacitively coupled readout single-electron transistor electrometers. The devices are prepared by electron beam direct-writing in conjunction with material deposition by sputtering. All leads are made of Al, and the AlO/sub x/ tunnel barriers are generated by local thermal oxidizing of the surface of the base striplines. The island electrodes are made of Al or Nb in a subsequent deposition step. In the case of Nb it is suitable to protect the barriers by a thin sputtered Al film first. The small-area (100 nm/spl times/100 nm) tunnel junctions have capacitances in the order of a few 10/sup -16/ F; their resistances can be adjusted in a wide range from k/spl Omega/ to M/spl Omega/ with an on-chip spread of less than 10%. The (double) superconducting gap energy was determined to be about 0.4 meV for Al and 1.4 meV for Nb, respectively. Measuring the so-called Coulomb staircase, we have demonstrated the operation of both qubit boxes and sub-e electrometers.
A multilevel thin-film process has been developed for fabricating experimental circuits containing Josephson tunneling gates, insulated crossings, superconducting contacts, and terminating resistors. The process utilizes a Nb film for the ground plane and Pb alloy films for overlying superconducting layers. Insulation is achieved through the use of vacuum-deposited SiO films and anodization of the Nb ground plane. An oxide formed by rf sputter-etching in an oxygen plasma is used for forming the tunneling barriers. Photoprocessing techniques are used for patterning. Through use of the process it has been possible to fabricate experimental memory and logic circuits which survive thermal cycling to 4.2 K and intervening storage at room temperature without significant changes in electrical characteristics.