Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Letters

Temporal compression of cw diode-laser output into short pulses with cesium-vapor group-velocity dispersion

Kyunam Choi, J. Menders, David Ross, Eric J. Korevaar

Published Nov 15, 1993• 1 citation
Publisher

Abstract

Using a technique similar to chirped pulse compression, we have compressed the 50-mW cw output of a diode laser into pulses of greater than 500-mW peak power and less than 400-ps duration. By applying a small current modulation to the diode, we induced a small wavelength modulation in the vicinity of the 6s(1/2)-to-6p(3/2) cesium resonance transition at 852 nm. Group-velocity dispersion on propagation through a cesium vapor cell then led to pulse compression. We developed a simple model to make predictions of output pulse shapes by using different modulation waveforms.

DOI
10.1364/ol.18.001902

Related papers

Passive pulse train generation from a frequency modulated diode laser

J. Menders, Kyunam Choi, Eric J. Korevaar

By sweeping the frequency of a diode laser beam near the cesium resonance frequency, followed by propagation through a short length of cesium vapor, we obtained periodic peaks with peak-to-average ratios near 5 at pulse repetition rates up to a gigahertz. Light in the wings of a strong atomic absorption line of an alkali metal vapor encounters large group velocity dispersion. A frequency modulation in an off-resonance cw beam passing through the vapor consequently develops an amplitude modulation. For certain combinations of laser and vapor parameters, a sinusoidally frequency modulated beam can be made to develop peaks. We generated pulse trains in a frequency modulated single mode diode laser tuned to the cesium absorption line near 852 nm, which we observed by using a fast p-i-n photodiode and a sampling oscilloscope. The frequency of a diode laser was sinusoidally modulated with a sweep of about a gigahertz and a period of a few nansoseconds by introducing a small modulation into the laser pump current. We observed the formation of sharp peaks with a width of about one-tenth of the modulation period and a peak-to-background ratio of approximately 5.

Annual Meeting Optical Society of America•Jan 1, 1992•0 citations

The Diode Laser Manipulation Of Cesium Atoms (polarization, Stopping).

Richard N. Watts

The results of two experiments involving the rapid frequency modulation of diode lasers are presented. In the first experiment, a cesium beam of 10('14) atoms/sec is produced with more than 98% of the atoms in a single spin state. The beam is polarized by optically pumping it with a single diode laser whose frequency is switched between the 6s(F = 4)-6p(,3/2)(F = 5) and 6s(F = 3)-6p(,3/2)(F = 4) transitions at 100 kHz. To do this, the frequency response of a diode laser to changes in injection current was first determined and the injection current modified to force a jump of 9.2 GHz in 1.5 (mu)sec. The same laser is used to probe the atomic population distribution simultaneously. In the second experiment, two diode lasers, tuned to the 6s(F = 4)-6p(,3/2)(F = 5) and 6s(F = 3)-6p(,3/2)(F = 4) transitions, are used to cool and stop a beam of cesium atoms. The laser frequencies are swept to keep them in resonance with the slowing atoms. The same lasers are used to probe the resulting velocity distribution. More than 10('10) atoms/sec are slowed to a velocity of 0 (+OR-) 15 m/sec, corresponding to a temperature of 1(DEGREES)K. Both of these experiments demonstrate extremely simple and inexpensive ways to manipulate atomic cesium.

•Jan 1, 1986•0 citations

Efficient phase conjugation of a cw low-power laser diode in a short Cs vapor cell at 852 nm

Marcos Oriá, Daniel Bloch, M. Fichet +1 more

Up to 50% cw phase-conjugate reflectivity has been obtained with a 30-mW diode laser at 0.85 microm by means of resonant degenerate four-wave mixing on an optically thick, 1-mm-long Cs vapor cell. Self-oscillation of a Fabry-Perot cavity containing this Cs cell is demonstrated.

Optics Letters•Oct 1, 1989•34 citations

Cooling cesium atoms using diode lasers

Carl Wieman, R. N. Watts

We have cooled and stopped a beam of cesium atoms using frequency chirped diode lasers. In this technique, a moving atom absorbs and reemits many photons from a counter propagating laser that is frequency swept to keep it in resonance with an atomic transition. The resulting momentum transfer slows the atom. The basic approach is identical to that developed by Hall and co-workers, however, the use of diode lasers allows us to obtain the necessary frequency modulation simply by sweeping the laser injection current. We use two diode lasers tuned to each of the 6s hyperfine ground state levels to drive the 6s—6p3/2 transitions. Each laser is simultaneously swept over the Doppler profile of the 100°C thermal cesium beam to bring a substantial number to a stop. Using additional fast frequency modulation, the same lasers are used to probe the resulting velocity distribution. This technique allows us to bring ~106 atoms/cm3 to a temperature of 1 K. This method is an extremely simple and inexpensive way to produce cold atoms.

International Laser Science Conference•Jan 1, 1986•0 citations

Conversion of cw light into a train of subnanosecond pulses using frequency modulation and the dispersion of a near-resonant atomic vapor

John E. Bjorkholm, E. H. Turner, D. B. Pearson

Sinusoidally frequency-modulated cw laser light is converted into a train of repetitive short pulses by passing it through a nearly resonant atomic vapor. Using a 200-MHz modulation frequency and sodium vapor, pulses as short as 240 psec, having peak powers of 6.3 times the input power, have been obtained at 5890 Å. Calculation and experiment are in good agreement.

Applied Physics Letters•May 15, 1975•56 citations

Switching, amplifying, and chirping diode lasers with current pulses for high bandwidth quantum technologies

Gianni Buser

A series of simple and low-cost devices for switching, amplifying, and chirping diode lasers based on current modulation are presented. Direct modulation of diode laser currents is rarely sufficient to establish precise amplitude and phase control over light, as its effects on these parameters are not independent. These devices overcome this limitation by exploiting amplifier saturation and dramatically outperform commonly used external modulators in key figures of merit for quantum technological applications. Semiconductor optical amplifiers operated on either rubidium D line are recast as intensity switches and shown to achieve ON:OFF ratios >106 in as little as 50 ns. Current is switched to a 795 nm wavelength (Rb D1) tapered amplifier to produce optical pulses of few nanosecond duration and peak powers of 3 W at a similar extinction ratio. Fast rf pulses are applied directly to a laser diode to shift its emission frequency by up to 300 MHz in either direction and at a maximum chirp rate of 150 MHz ns-1. Finally, the latter components are combined, yielding a system that produces watt-level optical pulses with arbitrary frequency chirps in the given range and <2% residual intensity variation, all within 65 ns upon asynchronous demand. Such systems have broad application in atomic, molecular, and optical physics and are of particular interest to fast experiments simultaneously requiring high power and low noise, for example, quantum memory experiments with atomic vapors.

arXiv:2407.18788•Review of Scientific Instruments•Dec 1, 2024•0 citations
Using a technique similar to chirped pulse compression, we have compressed the 50-mW cw output of a diode laser into pulses of greater than 500-mW peak power and less than 400-ps duration. By applying a small current modulation to the diode, we induced a small wavelength modulation in the vicinity of the 6s(1/2)-to-6p(3/2) cesium resonance transition at 852 nm. Group-velocity dispersion on propagation through a cesium vapor cell then led to pulse compression. We developed a simple model to make predictions of output pulse shapes by using different modulation waveforms.
By sweeping the frequency of a diode laser beam near the cesium resonance frequency, followed by propagation through a short length of cesium vapor, we obtained periodic peaks with peak-to-average ratios near 5 at pulse repetition rates up to a gigahertz. Light in the wings of a strong atomic absorption line of an alkali metal vapor encounters large group velocity dispersion. A frequency modulation in an off-resonance cw beam passing through the vapor consequently develops an amplitude modulation. For certain combinations of laser and vapor parameters, a sinusoidally frequency modulated beam can be made to develop peaks. We generated pulse trains in a frequency modulated single mode diode laser tuned to the cesium absorption line near 852 nm, which we observed by using a fast p-i-n photodiode and a sampling oscilloscope. The frequency of a diode laser was sinusoidally modulated with a sweep of about a gigahertz and a period of a few nansoseconds by introducing a small modulation into the laser pump current. We observed the formation of sharp peaks with a width of about one-tenth of the modulation period and a peak-to-background ratio of approximately 5.
The results of two experiments involving the rapid frequency modulation of diode lasers are presented. In the first experiment, a cesium beam of 10('14) atoms/sec is produced with more than 98% of the atoms in a single spin state. The beam is polarized by optically pumping it with a single diode laser whose frequency is switched between the 6s(F = 4)-6p(,3/2)(F = 5) and 6s(F = 3)-6p(,3/2)(F = 4) transitions at 100 kHz. To do this, the frequency response of a diode laser to changes in injection current was first determined and the injection current modified to force a jump of 9.2 GHz in 1.5 (mu)sec. The same laser is used to probe the atomic population distribution simultaneously. In the second experiment, two diode lasers, tuned to the 6s(F = 4)-6p(,3/2)(F = 5) and 6s(F = 3)-6p(,3/2)(F = 4) transitions, are used to cool and stop a beam of cesium atoms. The laser frequencies are swept to keep them in resonance with the slowing atoms. The same lasers are used to probe the resulting velocity distribution. More than 10('10) atoms/sec are slowed to a velocity of 0 (+OR-) 15 m/sec, corresponding to a temperature of 1(DEGREES)K. Both of these experiments demonstrate extremely simple and inexpensive ways to manipulate atomic cesium.
We have cooled and stopped a beam of cesium atoms using frequency chirped diode lasers. In this technique, a moving atom absorbs and reemits many photons from a counter propagating laser that is frequency swept to keep it in resonance with an atomic transition. The resulting momentum transfer slows the atom. The basic approach is identical to that developed by Hall and co-workers, however, the use of diode lasers allows us to obtain the necessary frequency modulation simply by sweeping the laser injection current. We use two diode lasers tuned to each of the 6s hyperfine ground state levels to drive the 6s—6p3/2 transitions. Each laser is simultaneously swept over the Doppler profile of the 100°C thermal cesium beam to bring a substantial number to a stop. Using additional fast frequency modulation, the same lasers are used to probe the resulting velocity distribution. This technique allows us to bring ~106 atoms/cm3 to a temperature of 1 K. This method is an extremely simple and inexpensive way to produce cold atoms.
A series of simple and low-cost devices for switching, amplifying, and chirping diode lasers based on current modulation are presented. Direct modulation of diode laser currents is rarely sufficient to establish precise amplitude and phase control over light, as its effects on these parameters are not independent. These devices overcome this limitation by exploiting amplifier saturation and dramatically outperform commonly used external modulators in key figures of merit for quantum technological applications. Semiconductor optical amplifiers operated on either rubidium D line are recast as intensity switches and shown to achieve ON:OFF ratios >106 in as little as 50 ns. Current is switched to a 795 nm wavelength (Rb D1) tapered amplifier to produce optical pulses of few nanosecond duration and peak powers of 3 W at a similar extinction ratio. Fast rf pulses are applied directly to a laser diode to shift its emission frequency by up to 300 MHz in either direction and at a maximum chirp rate of 150 MHz ns-1. Finally, the latter components are combined, yielding a system that produces watt-level optical pulses with arbitrary frequency chirps in the given range and <2% residual intensity variation, all within 65 ns upon asynchronous demand. Such systems have broad application in atomic, molecular, and optical physics and are of particular interest to fast experiments simultaneously requiring high power and low noise, for example, quantum memory experiments with atomic vapors.