Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

High-temperature superconducting Josephson mixers from deliberate grain boundaries in Tl2CaBa2Cu2O8

Lincoln C. Bourne, Albert Humirang Cardona, Tim W. James, John S. Fleming, Roger J. Forse, Robert B. Hammond, Jin Pyo Hong, T. W. Kim, Harold R. Fetterman

Published Jul 1, 1991• 2 citations
Publisher

Abstract

Deliberate grain boundaries have been fabricated in epitaxial films of Tl2CaBa2Cu2O8 by growing the films on substrates with localized surface damage and on substrates with surface steps produced with an anisotropic etching process. Bowtie antennas were fabricated to couple millimeter wave radiation into the weak link junctions, which were used as the nonlinear elements. Heterodyne mixing of signals at 55 GHz and 94 GHz was observed in the integrated antenna/detector structures at temperatures below 101 K in the Tl-based films. In addition, observations were made at 55 GHz, using these structures as subharmonic mixers. We have designed an integrated microwave package to measure the noise and conversion efficiency of the grain-boundary junctions at frequencies between 9 GHz and 20 GHz.

DOI
10.1117/12.45610

Related papers

Millimeter-wave detection by GBJJ using high-T/sub c/ superconducting YBaCuO films

S. Kita, H. Tanabe, Takeshi Kobayashi

Millimeter-wave detection in the heterodyne mixing mode has been carried out using the high-T/sub c/ superconducting GBJJ (grain boundary Josephson junction). The GBJJ was fabricated from high T/sub c/ superconducting Y-Ba-Cu-O films, prepared on YSZ and SrTiO/sub 3/ substrates using an RF sputtering technique. The junction was patterned by chemical wet etching with phosphoric acid solution. The authors carried out experiments in the heterodyne mixing mode for a signal of 35 GHz with local oscillation at 34.97 GHz. The detected IF (intermediate frequency) output power was obtained at a bias voltage lying midway between the zeroth and first Shapiro steps. A mixer conversion efficiency of -15 dB was obtained with a dynamic range of about 20 dB at 35 GHz. This result strongly implies that high-T/sub c/ superconducting GBJJ works well as a detector at millimeter-wave frequencies.>

IEEE Transactions on Magnetics•Mar 1, 1989•16 citations

YBCO microwave grain boundary mixer using a SrTiO/sub 3/ bicrystal substrate

R. Seed, Paul C. Dorsey, Hoton How +2 more

A microwave mixer was patterned on a microstrip transmission line of superconducting YBCO (YBa/sub 2/Cu/sub 3/O/sub 7-x/). The YBCO film was epitaxially laser deposited on a SrTiO/sub 3/ bicrystal substrate. A weak link was constructed by patterning a microbridge in the microstrip at the bicrystal boundary. Microwave signals at 9.000 GHz and 9.941 GHz were applied at the input of the microstrip line. An output intermediate frequency signal was observed at 941 MHz and was detected as the transmitted signal. The microbridge junction, which behaved as a resistively shunted Josephson junction (RSJ), was current biased slightly above the critical current I/sub c/. The mixer conversion loss was measured at the input and output ports of the device package. The mixing efficiency was determined at the device junction. This efficiency was compared with the calculated efficiency determined by numerical solution of the Josephson equation for the weak link junction.>

IEEE Transactions on Magnetics•Nov 1, 1993•4 citations

Millimeter Wave Mixing Properties of EuBa 2Cu 3O 7-δ Bicrystal Grain Boundary Junction Arrays

Koji Tsuru, Kazunori Miyahara, Minoru Suzuki

We report the millimeter wave mixing properties of high-T c superconductor Josephson junction arrays using a waveguide-to-microstrip converter in the 100 GHz frequency range. The junction arrays consist of 3 weak links fabricated from EuBa2Cu3O7-δ thin films grown on an MgO bicrystal substrate. In these junction arrays, Shapiro steps are observed in the presence of 100 GHz irradiation at intervals of 3 times the fundamental step voltage. Millimeter wave mixing with an input local oscillator frequency of 99.142 GHz and an input signal frequency of 99.880 GHz is detected as the IF output at 738 MHz. The IF output power peaks at voltages corresponding to those of the dynamic resistance dV/ dI. A mixing conversion efficiency of -24.1 dB is obtained for a 3-junction array.

Japanese Journal of Applied Physics•Dec 1, 1996•1 citation

Noise temperature measurement of YBCO Josephson mixers in millimeter and submillimeter waves

Hisashi Shimakage, Yoshinori Uzawa, Masayoshi Tonouchi +1 more

We have investigated YBCO step-edge Josephson junctions as millimeter and submillimeter wave mixers. These mixers were integrated with an Au thin-film log-periodic antenna designed for broadband coupling of the radiation. We estimated the noise temperature of the mixer using conventional hot/cold blackbody irradiation techniques in the 100- and 300-GHz bands. We found that the Au thin-film antenna yielded about 5 dB higher coupling efficiency than that of YBCO thin film antenna, and the noise temperature decreased from 2,800 K to 1,800 K. The best receiver noise temperature, 1,200 K, was achieved in the 300-GHz band through improvement in impedance matching.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•26 citations

Optimization of a 115 GHz waveguide mixer based on an HTS Josephson junction

Oliver Harnack, Marian Darula, Jens Scherbel +4 more

A waveguide mixer based on a Josephson junction made from a high-temperature superconductor (HTS) has been analysed at frequencies of 90 GHz and 115 GHz. The mixer consisted of a single-grain-boundary bicrystal junction which was integrated with a bow-tie antenna and a microstrip filter structure fabricated on an MgO substrate. Two different designs of mixer block were tested. Using the first design the best noise performance was measured at a local oscillator (LO) frequency of about 90 GHz. At the projected LO frequency of 115 GHz significant deterioration of performance was observed. A computer simulation of the mixer chip and substrate channel structure was performed using the 3D simulation program HFSS. Sufficient RF signal rejection by the filter structure was confirmed at 90 GHz. After a simulation cycle at 115 GHz the substrate channel in the mixer block was modified. Using this second design we measured a double-sideband mixer noise temperature of 1090 K at 10 K operating temperature which is the best performance of an HTS Josephson mixer to date obtained at this frequency and temperature.

Superconductor Science and Technology•Nov 1, 1999•25 citations

Planar superconducting YBCO microwave mixer employing an engineered grain boundary weak link junction

R. Seed, Paul C. Dorsey, Hoton How +2 more

A microstrip transmission line was patterned from a superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ film which was laser deposited on a SrTiO/sub 3/ bicrystal substrate. A microbridge in the microstrip was then patterned at the bicrystal interface to fabricate a superconducting grain boundary junction. Microwave mixing was observed with an input local oscillator frequency of 9.000 GHz, and an input signal frequency of 9.941 GHz. The output signal at 941 MHz was detected as a transmitted signal. The junction was current biased slightly above the critical current I/sub c/. The measured conversion loss was compared to the calculated value based upon a numerical solution of the equation for a superconducting weak link junction.>

IEEE Transactions on Applied Superconductivity•Jan 1, 1994•6 citations
Deliberate grain boundaries have been fabricated in epitaxial films of Tl2CaBa2Cu2O8 by growing the films on substrates with localized surface damage and on substrates with surface steps produced with an anisotropic etching process. Bowtie antennas were fabricated to couple millimeter wave radiation into the weak link junctions, which were used as the nonlinear elements. Heterodyne mixing of signals at 55 GHz and 94 GHz was observed in the integrated antenna/detector structures at temperatures below 101 K in the Tl-based films. In addition, observations were made at 55 GHz, using these structures as subharmonic mixers. We have designed an integrated microwave package to measure the noise and conversion efficiency of the grain-boundary junctions at frequencies between 9 GHz and 20 GHz.
Millimeter-wave detection in the heterodyne mixing mode has been carried out using the high-T/sub c/ superconducting GBJJ (grain boundary Josephson junction). The GBJJ was fabricated from high T/sub c/ superconducting Y-Ba-Cu-O films, prepared on YSZ and SrTiO/sub 3/ substrates using an RF sputtering technique. The junction was patterned by chemical wet etching with phosphoric acid solution. The authors carried out experiments in the heterodyne mixing mode for a signal of 35 GHz with local oscillation at 34.97 GHz. The detected IF (intermediate frequency) output power was obtained at a bias voltage lying midway between the zeroth and first Shapiro steps. A mixer conversion efficiency of -15 dB was obtained with a dynamic range of about 20 dB at 35 GHz. This result strongly implies that high-T/sub c/ superconducting GBJJ works well as a detector at millimeter-wave frequencies.>
A microwave mixer was patterned on a microstrip transmission line of superconducting YBCO (YBa/sub 2/Cu/sub 3/O/sub 7-x/). The YBCO film was epitaxially laser deposited on a SrTiO/sub 3/ bicrystal substrate. A weak link was constructed by patterning a microbridge in the microstrip at the bicrystal boundary. Microwave signals at 9.000 GHz and 9.941 GHz were applied at the input of the microstrip line. An output intermediate frequency signal was observed at 941 MHz and was detected as the transmitted signal. The microbridge junction, which behaved as a resistively shunted Josephson junction (RSJ), was current biased slightly above the critical current I/sub c/. The mixer conversion loss was measured at the input and output ports of the device package. The mixing efficiency was determined at the device junction. This efficiency was compared with the calculated efficiency determined by numerical solution of the Josephson equation for the weak link junction.>
We report the millimeter wave mixing properties of high-T c superconductor Josephson junction arrays using a waveguide-to-microstrip converter in the 100 GHz frequency range. The junction arrays consist of 3 weak links fabricated from EuBa2Cu3O7-δ thin films grown on an MgO bicrystal substrate. In these junction arrays, Shapiro steps are observed in the presence of 100 GHz irradiation at intervals of 3 times the fundamental step voltage. Millimeter wave mixing with an input local oscillator frequency of 99.142 GHz and an input signal frequency of 99.880 GHz is detected as the IF output at 738 MHz. The IF output power peaks at voltages corresponding to those of the dynamic resistance dV/ dI. A mixing conversion efficiency of -24.1 dB is obtained for a 3-junction array.
We have investigated YBCO step-edge Josephson junctions as millimeter and submillimeter wave mixers. These mixers were integrated with an Au thin-film log-periodic antenna designed for broadband coupling of the radiation. We estimated the noise temperature of the mixer using conventional hot/cold blackbody irradiation techniques in the 100- and 300-GHz bands. We found that the Au thin-film antenna yielded about 5 dB higher coupling efficiency than that of YBCO thin film antenna, and the noise temperature decreased from 2,800 K to 1,800 K. The best receiver noise temperature, 1,200 K, was achieved in the 300-GHz band through improvement in impedance matching.
A waveguide mixer based on a Josephson junction made from a high-temperature superconductor (HTS) has been analysed at frequencies of 90 GHz and 115 GHz. The mixer consisted of a single-grain-boundary bicrystal junction which was integrated with a bow-tie antenna and a microstrip filter structure fabricated on an MgO substrate. Two different designs of mixer block were tested. Using the first design the best noise performance was measured at a local oscillator (LO) frequency of about 90 GHz. At the projected LO frequency of 115 GHz significant deterioration of performance was observed. A computer simulation of the mixer chip and substrate channel structure was performed using the 3D simulation program HFSS. Sufficient RF signal rejection by the filter structure was confirmed at 90 GHz. After a simulation cycle at 115 GHz the substrate channel in the mixer block was modified. Using this second design we measured a double-sideband mixer noise temperature of 1090 K at 10 K operating temperature which is the best performance of an HTS Josephson mixer to date obtained at this frequency and temperature.
A microstrip transmission line was patterned from a superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ film which was laser deposited on a SrTiO/sub 3/ bicrystal substrate. A microbridge in the microstrip was then patterned at the bicrystal interface to fabricate a superconducting grain boundary junction. Microwave mixing was observed with an input local oscillator frequency of 9.000 GHz, and an input signal frequency of 9.941 GHz. The output signal at 941 MHz was detected as a transmitted signal. The junction was current biased slightly above the critical current I/sub c/. The measured conversion loss was compared to the calculated value based upon a numerical solution of the equation for a superconducting weak link junction.>