Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Investigation of planar switches for large format CMB polarization instruments

Paul Grimes, G. Yassin, L. S. Kuzmin, Philip D. Mauskopf, Ernst Otto, Michael E. Jones, Chris E. North

Published Jun 14, 2006• 6 citations
Publisher

Abstract

Several technologies are now being considered for modulating the polarization in various B-mode instruments, including rotating quasioptical half-wave plates in front of the focal plane array, rotating waveguide half-wave plates and Faraday rotators. It is not at all clear that any of these techniques is feasible without heavy penalty in cost or performance. A potentially much more efficient method is to use a pseudo-correlation polarimeter in conjunction with a planar circuit phase switch. We investigate three different devices for use as mm-wave switches, SIS tunnel junctions, capacitively coupled superconducting nanostrips and RF MEMS. The SIS tunnel junction switches operate by switching between two different bias voltages, while the nanostrip switch operates by changing the impedance of a resonant circuit by driving the nanostrip from the superconducting to normal state. In each case the RF signal sees two substantially different complex impedance states, hence could be switched from one transmission line branch to another. In MEMS this is achieved by mechanical movement of one plate of a parallel plate capacitor system. Although RF MEMS have been reported at high microwave and low mm-wave frequencies, in this work we have investigated cryogenic MEMS for operation at high mm-wave frequencies (225 GHz) using superconducting transmission lines. We present and compare designs and simulations of the performance of phase switches based on all three switching technologies, as well as preliminary experimental results for each of the switches. Finally we also present designs of phase shift circuits that translates the on/off switching into phase modulation.

DOI
10.1117/12.671151

Related papers

MM wave quasioptical SIS mixers

Qing Hu, C. A. Mears, P. L. Richards +1 more

The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>

IEEE Transactions on Magnetics•Mar 1, 1989•32 citations

Superconducting RF tuning circuits for low-noise submillimeter wave SIS receivers

Pascal Febvre, William R. McGrath, B. Bumble +4 more

Heterodyne receivers using SIS (Superconductor-Insulator-Superconductor) junctions are the most sensitive receivers for radioastronomy in the millimeter wave and submillimeter wave frequency range. These instruments use superconducting RF tuning circuits to resonate out the high shunt capacitance of the SIS junction in order to provide a good impedance match with the microwave envionment at the frequency of operation. An accurate model to determine the electrical propeties of impedance matching circuits has been developed. An analysis of superconducting microstrip lines and radial stubs taking into account the fringing fields of the thick electrode, the step discontinuities, and the Mattis-Bardeen complex conductivity for the superconductor surface impedance is presented. This model is used to calculate the resonance frequencies of the matching circuit with the capacitively-'shunted SIS junction. Good agreement is found between calculated and experimentally measured resonance frequencies at 550-600 GHz.

European Microwave Conference (EuMC)•Oct 1, 1994•1 citation

Superconducting IF biasing circuit for low-noise cryogenic applications

Dimitar Dochev, Raquel Rodriguez Monje, Vessen Vassilev +1 more

A planar superconducting circuit designed for use in low-noise cryogenic applications is presented. The circuit is a bias-T combined with a 4–8 GHz impedance matching circuitry, which employs entirely planar design with a novel layout. The proposed and tested circuitry is intended to be used with a SIS mixer and incorporates a double section transformer based on microstrip line technology with a total impedance transformation of 5:1 within the frequency band. One of the transformer sections employs a three-line coupled line, which also serves as a DC block capacitor. The microstrip lines were manufactured using superconducting Nb metallization, which provides a conduction loss-free solution at the operation temperature of 4 K. S-parameter measurements at 4 K temperature were performed and found to be in a good agreement with the simulations. The device measured return loss is better than −10 dB within the frequency band. Furthermore, the circuit was tested as a part of 385 – 500 GHz double sideband heterodyne SIS receiver demonstrating a flat noise temperature response of 80 – 90 K over the entire IF band of 4 – 8 GHz.

Journal of Physics Conference Series•Jun 1, 2010•2 citations

Superconducting Microwave Resonator Arrays for Submillimeter/Far-infrared Imaging

Omid Noroozian

Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.

•Jun 12, 2012•11 citations

A superconducting millimetre switch with multiple nano-bridges

Boon-Kok Tan, G. Yassin, L. S. Kuzmin +3 more

In this paper, we describe the design of a planar superconducting on/off switch comprising a high normal resistance nano-bridge deposited across a slotline transmission line. We present preliminary experimental results measured at 220 GHz range, and we discuss in detail the various parameters that affect the performance of the planar on/off switch, including the optimum thickness required for the nano-bridge to achieve high dynamic range and low transmission loss. The analysis is done by combining the accurate superconducting surface impedance description with rigorous electromagnetic simulations, and comparing the simulated results with the measured performance of a previously fabricated on/off switch fed by a backto- back unilateral finline taper. Finally, we propose an improved method to further increase the dynamic range of the switch, by introducing a multi-bridge design to tune out the residual inductance of the nano-bridges.

•Jan 1, 2014•4 citations

Quasi-optical Josephson direct detectors for millimeter wave spectrum analysis

Michael A. Tarasov, G.V. Prokopenko, G. A. Ovsyannikov +5 more

A quasioptical Josephson detector with resistively shunted superconducting tunnel junctions of superconductor-insulator-superconductor (SIS) type and different integrated matching circuits for mm waveband region has been designed, fabricated and experimentally studied. A special quasioptical cryogenic probe has been designed and fabricated for measurements of microwave response of such integrated receiving structures. For low-frequency matching a cold transformer has been used at the output port. Many efforts have been made for reducing the external noise influence on Josephson junction IV curve. Quasioptical beamguide has been optimized and adjusted using Bi bolometers evaporated instead of Josephson junctions in the center of planar antenna. Beampatterns of several types of planar antennas, including self-complementary and non-complementary logarithmic spiral and log-periodic antennas, have been measured using the same technique.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Aug 19, 1994•0 citations
Several technologies are now being considered for modulating the polarization in various B-mode instruments, including rotating quasioptical half-wave plates in front of the focal plane array, rotating waveguide half-wave plates and Faraday rotators. It is not at all clear that any of these techniques is feasible without heavy penalty in cost or performance. A potentially much more efficient method is to use a pseudo-correlation polarimeter in conjunction with a planar circuit phase switch. We investigate three different devices for use as mm-wave switches, SIS tunnel junctions, capacitively coupled superconducting nanostrips and RF MEMS. The SIS tunnel junction switches operate by switching between two different bias voltages, while the nanostrip switch operates by changing the impedance of a resonant circuit by driving the nanostrip from the superconducting to normal state. In each case the RF signal sees two substantially different complex impedance states, hence could be switched from one transmission line branch to another. In MEMS this is achieved by mechanical movement of one plate of a parallel plate capacitor system. Although RF MEMS have been reported at high microwave and low mm-wave frequencies, in this work we have investigated cryogenic MEMS for operation at high mm-wave frequencies (225 GHz) using superconducting transmission lines. We present and compare designs and simulations of the performance of phase switches based on all three switching technologies, as well as preliminary experimental results for each of the switches. Finally we also present designs of phase shift circuits that translates the on/off switching into phase modulation.
The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>
Heterodyne receivers using SIS (Superconductor-Insulator-Superconductor) junctions are the most sensitive receivers for radioastronomy in the millimeter wave and submillimeter wave frequency range. These instruments use superconducting RF tuning circuits to resonate out the high shunt capacitance of the SIS junction in order to provide a good impedance match with the microwave envionment at the frequency of operation. An accurate model to determine the electrical propeties of impedance matching circuits has been developed. An analysis of superconducting microstrip lines and radial stubs taking into account the fringing fields of the thick electrode, the step discontinuities, and the Mattis-Bardeen complex conductivity for the superconductor surface impedance is presented. This model is used to calculate the resonance frequencies of the matching circuit with the capacitively-'shunted SIS junction. Good agreement is found between calculated and experimentally measured resonance frequencies at 550-600 GHz.
A planar superconducting circuit designed for use in low-noise cryogenic applications is presented. The circuit is a bias-T combined with a 4–8 GHz impedance matching circuitry, which employs entirely planar design with a novel layout. The proposed and tested circuitry is intended to be used with a SIS mixer and incorporates a double section transformer based on microstrip line technology with a total impedance transformation of 5:1 within the frequency band. One of the transformer sections employs a three-line coupled line, which also serves as a DC block capacitor. The microstrip lines were manufactured using superconducting Nb metallization, which provides a conduction loss-free solution at the operation temperature of 4 K. S-parameter measurements at 4 K temperature were performed and found to be in a good agreement with the simulations. The device measured return loss is better than −10 dB within the frequency band. Furthermore, the circuit was tested as a part of 385 – 500 GHz double sideband heterodyne SIS receiver demonstrating a flat noise temperature response of 80 – 90 K over the entire IF band of 4 – 8 GHz.
Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.
In this paper, we describe the design of a planar superconducting on/off switch comprising a high normal resistance nano-bridge deposited across a slotline transmission line. We present preliminary experimental results measured at 220 GHz range, and we discuss in detail the various parameters that affect the performance of the planar on/off switch, including the optimum thickness required for the nano-bridge to achieve high dynamic range and low transmission loss. The analysis is done by combining the accurate superconducting surface impedance description with rigorous electromagnetic simulations, and comparing the simulated results with the measured performance of a previously fabricated on/off switch fed by a backto- back unilateral finline taper. Finally, we propose an improved method to further increase the dynamic range of the switch, by introducing a multi-bridge design to tune out the residual inductance of the nano-bridges.
A quasioptical Josephson detector with resistively shunted superconducting tunnel junctions of superconductor-insulator-superconductor (SIS) type and different integrated matching circuits for mm waveband region has been designed, fabricated and experimentally studied. A special quasioptical cryogenic probe has been designed and fabricated for measurements of microwave response of such integrated receiving structures. For low-frequency matching a cold transformer has been used at the output port. Many efforts have been made for reducing the external noise influence on Josephson junction IV curve. Quasioptical beamguide has been optimized and adjusted using Bi bolometers evaporated instead of Josephson junctions in the center of planar antenna. Beampatterns of several types of planar antennas, including self-complementary and non-complementary logarithmic spiral and log-periodic antennas, have been measured using the same technique.